Facing TV Problems? Ask a TV Technician.

Ask an Expert, Get an Answer ASAP!

Zenith Projection TV Questions

Zenith Projection TV‘s offer a high resolution display with a widescreen effect as well as Surround Sound System. They also allow their viewers to customize the settings according to their preferences so that they can enjoy an enhanced quality of TV viewing. You can also tune in to a lot of your favorite stations effortlessly due to its high performance signal receiver. However with any other electronic, Zenith projection TV can malfunction or not work correctly. Often when this happens, questions may rise that needs answered on how to troubleshoot or fix the problems. Below are frequently asked questions on issues relating to Zenith Projection TV sets that have been answered by the Experts.

If a Zenith Projection TV has good audio but the picture is not there and turning it off and restarting helps the TV to work for a few days then the issues happen again, what could be the problem and how can it be fixed?

In many cases like this, the problem could be a bad power cord due to faulty capacitors. If this is the case, the best course of action would be to contact an Expert to service the television.

What could cause a Zenith Projection TV to shut off forty seconds after it’s turned on, and the red light blinks followed by the temp light when it shuts off

In some cases the lamp inside of the TV can fail and could require a new lamp. Various electronic stores sell the replacement lamp. Usually, these lamps could run for three to five years on an average.

Is it possible to install a new lamp on a Zenith Projection TV without a technicians help?

Most of the time, a technician may not be needed if there is enough knowledge on how to replace the lamp. Many electronic stores sell the replacement lamp. A person could visit “Do it yourself” sites online for additional help.

What could cause the auto convergence on a Zenith Projection TV to not work properly, and the red, green, and blue tint seems to unaligned as well as the screen looks to be bent in the center, top and bottom?

It could be that the convergence circuit inside the Zenith projection unit has failed. However, this kind of a failure is not very unusual. These convergence IC chips tend to go bad and stop working after they have been used over a period of time. In most cases, it is the heat that causes these chips to go bad.

If a Zenith Projection TV has stopped working after a power surge what is the problem if the TV made a popping noise first?

In some cases, the power supply seems fail which causes the TV to not power. But, in some cases, it’s always better to check the fuse at first. A blown fuse could also cause such problems to arise. If the fuse has blown out, then it is likely to be a simple fix. You could unscrew and remove the entire back cover of your unit to have access to the fuse. You would find it on the board to which the power cord is plugged in. All you would have to do is install a new fuse of the same type and rating. You should be able to get that from any local hardware store. However, if this does not power up your TV, then it is probably the capacitor or the IC that have shorted, causing the popping sound to occur. In that case, there is no easy fix for this repair. You would need to replace or repair the faulty component. You can experience many different problems with your Zenith Projection TV sets. These problems could include issues like loose cable connections, poor audio/visual adjustments, magnetization problems and so on, which may disrupt your TV viewing experience. However, these problems could be fixed by mere troubleshooting. In case it doesn’t, then a professional’s help would be necessary. If you need clarification about your specific situation with respect to issues related to Zenith Projection TV sets, you may ask a TV Technician Expert to evaluate your case details and provide a technical insight.
Please type your question in the field below

3 verified TV Technicians are online now

TV Technicians on JustAnswer are verified through an extensive 8-step process including screening of licenses, certifications, education and/or employment. Learn more



Associate Degree

2875 positive reviews

TV & Communications Sys Repair

Graduate Certificate

2355 positive reviews


Vocational, Technical or Trade Scho

1424 positive reviews
See all TV Technicians
JustAnswer in the news:
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
Web sites like
...leave nothing to chance.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.