Small Engine

Small Engine Troubleshooting Problems? Ask a Mechanic Now.

Connect one-on-one with {0} who will answer your question

Related Small Engine Questions
I have a 17 kW generac whole house generator. Battery is
I have a 17 kW generac whole house generator. Battery is charged and fuse is good. No LED display. Blank. I am guessing a board issue? … read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
Do you work for hank. A few times. I need someone who knows
i need someone who knows centerion generac generators Centurion/generac generator model #004987. High idle and then shuts off. Found 25 ohm 5% 25w resistor burnt and not working. (owners manual pg 21 item R1) Replaced resistor and generator ran in use for about 14 hrs. Started it a couple times since then just to let it run a bit with no issues. Went to start it today and had the same symptoms. Same thing resistor burnt again. put another on and in about 1 min it starts smoking. I believe its a voltage regulator problem. What's your opinion?Detail Required: LOW; Urgency: LOW… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
Have a generac 0064591, 16k standby. The new evolution
have a generac(###) ###-#### 16k standby. The new evolution control was reading fix harness resistor. I did a reset, but it still is not putting out 12v on 194 during automatic startup. Maybe control … read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
I have a standby generator modeland need a control oh6680d
I have a standby generator model(###) ###-####and need a control ass oh6680d rev j c1308. where can I find this? … read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
My howl house Generac generator stoped working. I will have
I will have to get that info. I will get back to you. … read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
I have a Generac model sd25/16471, serial no. 0774976
I have a Generac model sd25/16471, serial no.(###) ###-####diesel. Engine runs fine and was producing electricity. It has stopped making electricity. I bought it used and never got a manual and don't have schematics. … read more
Wayne
Wayne
Grand Pa
Vocational, Technical or Trade Scho
4,438 satisfied customers
My General 20kW generator Model 58750 (about 6 years old)
My General 20kW generator Model 58750 (about 6 years old) apparently suffered a surge and all three 5 amp fuses blew. I replaced them and the display looks normal even when switched to automatic. When… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
My Generac 20Kw is not getting on Auto mode. Shows an error
My Generac 20Kw is not getting on Auto mode. Shows an error display 'Gen under voltage' what does this mean? Couple of months it came with an error 'low battery voltage' even though it is a new batter… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
I have a Generac modelstandby generator. The serial # isand
Hi, I have a Generac model(###) ###-####standby generator. The serial # *****(###) ###-####and the controller p/n is 0H6680B. I need a new controller and was curious whether a 0H6680D can be substitut… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
I have a Generac model number(###) ###-#### *****#6110459 and the computer
I have a Generac model number(###) ###-#### *****#6110459 and the computer will not keep its date and time. I have been told I need to replace the very expensive control panel. Could you tell me what … read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
I have an Onan 4.0 CCK Spec R that fried the 300C859 board.
I have an Onan 4.0 CCK Spec R that fried the 300C859 board. I got another one and installed it, placing all wires at the proper terminals. After starting the Genset, the very same resistor, R1, got ex… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
have a 17 kw generator with a automatic transfer switch when
have a 17 kw generator with a automatic transfer switch when utilty power is off generator starts but wont switch transfer switch no power at any time on 194… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
Have a 1990 mod. # XXXXX Works and runs fine. Someone
Have a 1990 mod. # XXXXX Works and runs fine. Someone previously installed a switch that powers the fuel pump. Would like to correct this and remove switch so it is wired correctly. I think if I could… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
I am trying to find the electronic schematics for a Generac
I am trying to find the electronic schematics for a Generac 7550 generator.model 01470. It has a 83970 Rev U control board which has a blown regulator chip. There are two chips on the board and I can … read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
My YTH2148 mower has had the common problem of blowing the
My YTH2148 mower has had the common problem of blowing the 20amp fuse when I start the blades. I have adjusted the pto clutch and it worked a few minutes then blew the fuse. I replaced the pto clutch … read more
Rick
Rick
Factory Authorized Trainer
Vocational, Technical or Trade Scho
4,218 satisfied customers
Generac Hondagenerator model 1069-0 series HP 2500 ff 230/115v
Generac Hondagenerator model 1069-0 series HP 2500 ff 230/115v 9.5/19 A No output voltage on either 230 or 115. Changed capacitor windings look good. Any suggestions as to problem and how to fix it.… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
We have a 1993 EZGO electric golf cart that has stopped running.
We have a 1993 EZGO electric golf cart that has stopped running. We were climbing a slight hill at low speed and heard a pop under the seat, the cart then stopped running. The solenoid is operating bu… read more
Curtis B.
Curtis B.
Technician
Associate Degree
18,036 satisfied customers
I have a onan 6.5k NH 3cr Gen and trying to get charging circit
I have a onan 6.5k NH 3cr Gen and trying to get charging circit to work right and of cours the person I got this from had someone repair it and changed the wiring I replace the r1 resistor from a 8 oh… read more
Hank F.
Hank F.
Technician
High School or GED
16,533 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

You did one super job of explaining to me everything there is to know about this fridge. I'm looking forward to asking you questions in the future.

JimmyBagley, IA

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

< Previous | Next >

Meet the Experts:

Curtis B.

Curtis B.

Technician

18,036 satisfied customers

have worked on and around most engine models for 35 yrs./Polaris ATV expert

Rick

Rick

Factory Authorized Trainer

4,218 satisfied customers

Outdoor Power Equipment technical trainer since 1990, covering eight states.

Vince O.

Vince O.

Small Engine Technician

3,047 satisfied customers

Over 30 years experience repairing lawn and garden equipment. Chainsaws, mowers,blowers and trimmers

Jon K.

Jon K.

Small Engine Diagnostic Expert

2,995 satisfied customers

Gold certified Stihl tech, Service Manager for a rental/repair shop.Certified in most small engines

James W

James W

Small Engine Troubleshooting Expert

2,987 satisfied customers

7 years as Mechanic & Parts Manager for Brother who has Owned Lawn & Garden Repair shop for 35 years

RUSS

RUSS

SERVICE TECHNICIAN

1,723 satisfied customers

28 YEAR SERVICE TECHNICIAN

CJBennett

CJBennett

Small Engine Technician

624 satisfied customers

Briggs and Stratton Master Service Tech, Kohler, Tecumseh, Kawasaki certified. 18 years exp.

< Previous | Next >

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x