Nissan

Nissan repair questions? Ask a mechanic for answers ASAP

Ask an Expert,
Get an Answer ASAP!

This answer was rated:

I am getting a p1610 error code. The engine starts fine. I…

I am getting a p1610...
I am getting a p1610 error code. The engine starts fine. I clear the code and a few trips later it returns. Any ideas?
Show More
Show Less
Ask Your Own Nissan Question
Answered in 4 minutes by:
10/26/2017
Clifton B.
Clifton B., ASE Master Auto Tech
Category: Nissan
Satisfied Customers: 4,833
Experience: ASE Master Certified Tech, Nissan Master Certified Tech, 12 yrs. experience in auto repair.
Verified

hi my name is ***** ***** I can help

Ask Your Own Nissan Question

is this code causing the service engine soon light to come on ??

Ask Your Own Nissan Question
Customer reply replied 8 months ago
it does but also A/F sensor error code is read by my handheld
Customer reply replied 8 months ago
P0101 AF sensor code error as well

the p1610 code is not a problem as long as the engine start , if you have this code and there is an real time problem the engine will not start so this most be cause by an internal conflict inside the bcm , you should try a hard rest to see if the code will go away . that is disconnect both battery cables and hold them touching away from the battery for one minute

Ask Your Own Nissan Question

the p0101 is the code that I would worry about fixing

Ask Your Own Nissan Question
Customer reply replied 8 months ago
I must also add that when I clear the codes with my handheld, the problem goes away for days, weeks or even months before the SERVICE ENGINE SOON indicator comes on

is that for the po101 or both

Ask Your Own Nissan Question

and is there any starting problems at any time and or engine running rough ??

Ask Your Own Nissan Question

r u there

Ask Your Own Nissan Question
Customer reply replied 8 months ago
Both codes are gone until the SERVICE ENGINE SOON comes on. Then they are there sometimes with p1211 TCS fault code. I clear the codes and it can go a long or short time before happening again

have you clean the mas air flow sensor yet

Ask Your Own Nissan Question
Customer reply replied 8 months ago
Engine runs fine with SES light on or off. Starts fine like new
Customer reply replied 8 months ago
I have cleaned and replaced the mass AF sensor. Including the wiring connector pins

would not worry about the 1610 c0de as long as the car start , the 1211 can be set because of the 0101

Clifton B.
Clifton B., ASE Master Auto Tech
Category: Nissan
Satisfied Customers: 4,833
Experience: ASE Master Certified Tech, Nissan Master Certified Tech, 12 yrs. experience in auto repair.
Verified
Clifton B. and 87 other Nissan Specialists are ready to help you
Ask your own question now

t​his is the sensor in the air box correct ??? the one you replace

Ask Your Own Nissan Question
Customer reply replied 8 months ago
I should also say the vehicle passes smog tests. Thank you for the NATS diagram. That was most enlightening. I consider this closed and than you very much

your welcome .

Ask Your Own Nissan Question
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a nissan mechanicLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask Clifton B. Your Own Question
Clifton B.
Clifton B.
Clifton B., ASE Master Auto Tech
Category: Nissan
Satisfied Customers: 4,833
4,833 Satisfied Customers
Experience: ASE Master Certified Tech, Nissan Master Certified Tech, 12 yrs. experience in auto repair.

Clifton B. is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

I was in trouble with an electrical issue with my brand new Nissan. I frantically went online trying to find help and luckily I found your site. I reached a NISSAN tech named RIP. He was absolutely tremendous and helped me work through the issue. What a pro!

cjazLexington, KY

I would (and have) recommend your site to others I was quite satisfied with the quality of the information received, the professional with whom I interacted, and the quick response time. Thanks, and be sure that I'll be back whenever I need a question answered in a hurry.

Stephanie PElm City, NC

used your service this weekend with "Trecers" help. thank you ,thank you, thank you. replaced an A/C fan motor. Local Auto Zone had part. $15.00 "tracer" fee and $40.00 for parts, I saved several hundreds of dollers at a shop. i will recommend you and use you in the future.

David L.Richmond, TX

9 dollars, 2 hours of my time, and I drove away. Your diagnosis was right on the mark. Thank you so much.

PhilMarysville, CA

Lurch. Thank you very much. I had real doubts about this website but your promptness of response, quick followup and to the point answer with picture was incredible.

CharlesWalnut Creek, CA

As a single woman, I really appreciate an excellent and affordable opinion.
Thank you Geordie, I will not hesitate to contact justanswer in the future!

SueCharleston, WV

Another great insight to what may be the problem. I will have my mechanic take a look at it tomorrow. Thanks again, Frank...you do indeed know your stuff.

JimCastleberry, FL

< Previous | Next >

Meet the Experts:

Chris(aka-Moose)

Chris(aka-Moose)

Nissan Technician

747 satisfied customers

16 years of experience

Tim Mohr

Tim Mohr

ASE MASTER TECH

602 satisfied customers

30 YRS EXPERIENCE, FOREIGN AND DOMESTIC, GAS AND DEISEL

Marty

Marty

ASE Certified Technician

161 satisfied customers

ASE & Bosch master tech. 30 years experience.

Mike V.

Mike V.

Nissan Technician

9,482 satisfied customers

Nissan factory trained and Certified Subaru Technician.

Ron

Ron

ASE Certified Technician

589 satisfied customers

34 years of automotive Repair

Anthony

Anthony

ASE Certified Technician

332 satisfied customers

ASE Master Automobile Technician with over 18 years exp. in this field.

Richard

Richard

ASE Certified Technician

92 satisfied customers

Nissan Tech ASE certified technician

< Previous | Next >

Related Nissan Questions
01 Maxima 3.0 engine. Keeps coming up with p0403 code. Won't
01 Maxima 3.0 engine. Keeps coming up with p0403 code. Won't rev past 2800 rpm. This car does not have an EGR valve … read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
I have a infinity i35 that will not fire, have never
i have a infinity i35 that will not fire, have never incountered this before with this car it has 150,000 mi, have a code reader and pulled codes p1610, p1612, and p1167. … read more
roy
roy
Associate Degree
3 satisfied customers
I have a 2013 Nissan versa pure drive sl, with 100k, I got
hi I have a 2013 Nissan versa pure drive sl, with 100k, I got check engine light and battery was weak I replaced battery checked the code it was u0100, cleared code and trying to drive vehicle it is s… read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
I HAD A NEW KEY CUT & PROGRAMED BY A LOCKSMITH, THE KEY
I HAD A NEW KEY CUT & PROGRAMED BY A LOCKSMITH, THE KEY WORKED THEN THE NEXT DAY WOULD NOT. NOW THE ONLY CODE I GET IS P1610 LOCK MODE ?? CAN NOT CLEAR … read more
Clifton B.
Clifton B.
ASE Master Auto Tech
4,833 satisfied customers
Got a 2005 navara, disconnected the battery yesterday to do
hi got a 2005 navara, disconnected the battery yesterday to do some welding and now it wont start. pulled codes p1610 & p1614 … read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
We just bought a 05 Nissan Xterra and tried an unprogramed
We just bought a 05 Nissan Xterra and tried an unprogramed key on it. Now it is messed up. We had no idea this would happen. What did we mess up and how do we fix it?… read more
Jake
Jake
309 satisfied customers
Pathfinder: , I have a 2003 pathfinder with 3.5. the
Hello, I have a 2003 pathfinder with 3.5. the truck will not fire. I have several codes p1610 p1612 p1614 u1000 u1001 it turns over fine but will not start. the security red light is flashing? what is… read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
I got a flashing air bag error signal on screen o my 2005
I got a flashing air bag error signal on screen o my 2005 Nissan Quest . A mechanic looked at the error codes. It had: CI727 battery not delivering enough power, main computer board error, control mod… read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
I have a 03 nissan altima that does not start alredy changed
i have a 03 nissan altima that does not start alredy changed the crank and cam sensor no security liten at all… read more
rpmdiag
rpmdiag
High school
7,755 satisfied customers
Pulsar: I have a code 1610 lock mode, and the car won't start.
I have a code 1610 lock mode, and the car won't start. I have changed the ECU, key and key reader twice. I can't program the key and it comes up as failed… read more
indy-tech
indy-tech
Shop owner, technician
Vocational, Technical or Trade Scho
11 satisfied customers
2003 maxima: se..wouldnt start..it wont start even with a jump
I have a 2003 maxima 3.5 se - At first I was having problems of it not starting - it was turning but wouldn't start - I'd get a jump and it would start. Then it would happen again and after a day or t… read more
Ryan
Ryan
Master Infiniti Tech
Associate Degree
4 satisfied customers
2001 Nissan Pathfinder: mechanics..dealership..nats reset module
p1610 NATS Lock out mode on 2001 Nissan Pathfinder I have the p1610 NATS issue on pathfinder 2001, but mechanics at the dealership do not have the NATS reset module in their scan, can it be downloaded… read more
Ryan
Ryan
Master Infiniti Tech
Associate Degree
4 satisfied customers
1996 Altima: 000 miles..It started to sputter and then stall..30 min
I have a 1996 Altima with 177,000 miles on it. It started to sputter and then stall out when I had it running 30 min. or so. I could get the car started until the engine cooled down. I changed the plu… read more
Rick
Rick
Master Technician (Team Leader)
Vocational, Technical or Trade Scho
350 satisfied customers
2001 Nissan Pathfinder: tach surges..Local mechanic..fault code
Howdy, 2001 Nissan Pathfinder with 145K miles showed "Service Engine Soon" light with small tach surges. Local mechanic can't get computer so show a fault code. Any ideas?… read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
2004 Nissan frontier XE: 4cyl..Check engine light..unhook
2004 Nissan frontier XE 4cyl, 5 sp, 69,000mi. Check engine light (vss code) returns after reset. I tried to install an aftermarkert cruise control and I believe I arked (didn't unhook the battery) the… read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
What a code p1615 NATS malfunction means or how to fix it.Can you
can you please explain what a code p1615 NATS malfunction means or how to fix it.Can you also tell me where its located on the motor? Thanks… read more
HondaPlatinum
HondaPlatinum
High School or GED
148 satisfied customers
I have a 2005 Nissan Altima SE that just had its crankshaft
I have a 2005 Nissan Altima SE that just had its crankshaft position sensor replaced. The speed sensor code aslo displayed, but I needed to know which one I should replace. I was told the speedometer … read more
FixUrNissan
FixUrNissan
Shop Forman / Lead Tech / Parent
Vocational, Technical or Trade Scho
1 satisfied customers
350Z: following trouble codes..drive train..other electrical problems
Please add details I have read the following trouble codes P1610 P1612 U1001 and something about drive train??? I recently have had other electrical problems is there an inherent problem with the elec… read more
Infiniti Nissan Specialist
Infiniti Nissan Specialist
Master Technician
Vocational, Technical or Trade Scho
915 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x