Medium and Heavy Trucks

Have truck repair questions? Ask an Expert

Connect one-on-one with {0} who will answer your question

This answer was rated:

Have codes 625-14p, 613-14a, 612-14p. 2003 international…

Have codes 625-14p, 613-14a...

Have codes 625-14p, 613-14a, 612-14p

Mechanic's Assistant: What's the make/model/year of your truck? Engine type?

2003 international 7400 dt530

Mechanic's Assistant: Are you fixing your truck yourself? What have you tried so far?

Yes, I charged the ac system, replaced HVAC door actuator

Mechanic's Assistant: Anything else you want the truck mechanic to know before I connect you?

The switch for the fan is flashing

Show More
Show Less
Ask Your Own Medium and Heavy Trucks Question
Answered in 2 minutes by:
3/6/2019
Technician: Mike Mcmillan, Shop Foreman/Triage Tech replied 3 years ago
Mike Mcmillan
Mike Mcmillan, Shop Foreman/Triage Tech
Category: Medium and Heavy Trucks
Satisfied Customers: 6,765
Experience: Volvo/Mack Master Tech, Certified with Cummins, Eaton, GM, Hino, Detroit Diesel
Verified
Hello and thank you for using Just Answer. My name is***** will be assisting you with your issue. Please allow me a few minutes to get these faults looked up for you. Thank you
Ask Your Own Medium and Heavy Trucks Question
Technician: Mike Mcmillan, Shop Foreman/Triage Tech replied 3 years ago

Your 625-14 is for the switch pack, door pod. The dash switches are multiplexed to the body controller. The other faults are communication faults. I would remove the kick panel to the left of your foot when your sitting in the drives seat. There you will find the body control module. Check all the connectors for any signs of corrosion. If non is found the unit should be connected to the DLB program to see which switch pack or pod is not talking over the link. You can check for proper power and ground to the packs. It is the non=twisted wiring. Please let me know if you need anything else. Thank you

Ask Your Own Medium and Heavy Trucks Question
Technician: Mike Mcmillan, Shop Foreman/Triage Tech replied 3 years ago

Your 613 fault is for the control head hot cold control mix, Make sure you reset the system if you changed the actuator. The 612 is a switch out of range but I will need the rest of the fault numbers to get the exact switch

Mike Mcmillan
Mike Mcmillan, Shop Foreman/Triage Tech
Category: Medium and Heavy Trucks
Satisfied Customers: 6,765
Experience: Volvo/Mack Master Tech, Certified with Cummins, Eaton, GM, Hino, Detroit Diesel
Verified
Mike Mcmillan and 87 other Medium and Heavy Trucks Specialists are ready to help you
Ask your own question now
Customer reply replied 3 years ago
i have reset the system several times by disconnecting the ground. The compressor will run for a minute or so then cut off and the check ac light will turn on and the fan switch will start flashing.there are 2 613 codes they read as follows, 1 3
613-14p
1 4
613-14a
Technician: Mike Mcmillan, Shop Foreman/Triage Tech replied 3 years ago

Okay, thanks for the rest of the fault info, I am looking this up now

The info for this fault is here. You will need to make sure that all the actuators are working because once this fault comes active it will kick the ac out.

Ask Your Own Medium and Heavy Trucks Question
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a technicianLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask Mike Mcmillan Your Own Question
Mike Mcmillan
Mike Mcmillan
Mike Mcmillan, Shop Foreman/Triage Tech
Category: Medium and Heavy Trucks
Satisfied Customers: 6,765
6,765 Satisfied Customers
Experience: Volvo/Mack Master Tech, Certified with Cummins, Eaton, GM, Hino, Detroit Diesel

Mike Mcmillan is online now

Related Medium and Heavy Trucks Questions
2007 INTERNATIONAL 4300 WITH HYDRAULIC BRAKES. THE BRAKE
2007 INTERNATIONAL 4300 WITH HYDRAULIC BRAKES. THE BRAKE FLUID LIGHT COMES ON AND OFF ABS LIGHT STAYS ON AND BRAKE PRESSURE LIGHT STAYS ON BUT BRAKES WORKS FINE … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
I have a 2004 international 7600, A/C wont switch on and
i have a 2004 international 7600, A/C wont switch on and getting multiple codes SPN 613 14 1:3, spn 625 14 15:17, spn 612 14 29:1 … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
2003 international 7400. 613 14a 1:1 code and no a/c. Pulled
2003 international 7400 JA: What's the make/model/year of your truck? Engine type? Customer: 613 14a 1:1 code and no a/c JA: Are you fixing your truck yourself? What have you tried so far? Customer: p… read more
Mike Mcmillan
Mike Mcmillan
Shop Foreman/Triage Tech
Associates
6,765 satisfied customers
2004 4300 int code 613 fmi 14 special instructions #3
2004 4300 int code 613 fmi 14 special instructions #3 replaced all 3 actuators cant clear codes to fully charge Freon capacity … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
Check Ac light back on. Here are the active codes 5:240
Hey Andy. Check Ac light back on. Here are the active codes 5:240 639_14p 7:17 625_14a 15:81 625-14a 15:17 625-14a… read more
Andy
Andy
truck /coach technician
Vocational, Technical or Trade School
214 satisfied customers
NO POWER, ON 2004 INTERNATIONAL 4300 WITH A DT 466 ENGINE.
NO POWER , ON 2004 INTERNATIONAL 4300 WITH A DT 466 ENGINE … read more
Andy
Andy
truck /coach technician
Vocational, Technical or Trade School
214 satisfied customers
2005 Int. 8600 Cummins last 8 VIN 5J157681, Getting codes
Getting codes 15:65 625-14A, 1:1 613-14P and 150:9 2023-14P … read more
Alex Olsen
Alex Olsen
auto/diesel/industrial
790 satisfied customers
I'm looking for a list of diagnostic codes for a 2006 int.
Good morning, I'm looking for a list of diagnostic codes for a 2006 int. 4300 dt466e … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
I have a 07 international DT466. just replaced erg valve and
I have a 07 international DT466. just replaced erg valve and fuse but still has no power and no power to the egr valve… read more
Jeremy
Jeremy
Certified Truck/Bus Technician
Associate Degree
2,756 satisfied customers
I have a 2006 international dt466 that iv been working on
Hi, i have a 2006 international dt466 that iv been working on today and have a few codes that i found, and im not sure if one has to do with the fuel gauge. i just got the a/c working again due to bad… read more
Andy
Andy
truck /coach technician
Vocational, Technical or Trade School
214 satisfied customers
2004 international 4300 dt466. the fuel gauge went started going to 6 o'clock. checke
2004 international 4300 dt466. the fuel gauge went started going to 6 o'clock. checked the sensor and wiring. all is fine. replaced the gauge. now the gauge sweeps normally, then goes from E all the w… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
I have a International 4400 dt570 2006 cab chassie, VIN 1HTMRAZK06H332762 service
I have a International 4400 dt570 2006 cab chassie, VIN 1HTMRAZK06H332762 service a/c light is on the dash a/c not working, checked pressures there good no power at the compressor, with a/c switch on … read more
sevn103
sevn103
232 satisfied customers
222mk, I have the code 1 fault 7then just below 613_14p Compressor
I have the code 1 fault 7 then just below 613_14p Compressor in op wont stay in gauged. New comp. dryer, flush freon, oil, What sensor controls the compressor clutch? Is it all 3 it has two thermostat… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
2006 International 7600 - the blower motor control only blows
2006 International 7600 - the blower motor control only blows heat/air out the front vents of the dash. When you switch to defrost or floor, it will not change from blowing out the front vents of the … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
Hi. I hope you can help me here i have a 2003 international
Hi. I hope you can help me here i have a 2003 international 4200 vt365 with a check transmission light that comes on after starting engine. i pulled codes and found a 2023 14 150 2, 63914 241 254, 639… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
2007 International 7600....AC functions correctly for 15
2007 International 7600....AC functions correctly for 15 mins. then shutsdown with 613_14a code… read more
tkman55
tkman55
Shop manager Trailer Refrigeration shop
138 satisfied customers
HI SEVN103 IM WORKING ON 2004 INTERNATIONAL 4400 STRAIGHT JOB.
HI SEVN103 IM WORKING ON 2004 INTERNATIONAL 4400 STRAIGHT JOB. CHECK AC LIGHT ON NO COMPRESSOR CLUTCH ENGUAGEMENT. CHECK ALL FUSES IN CAB OK. SOMEONE HAD HOT WIRE ON CLUTCH COIL. STATIC PRESSURES ARE … read more
sevn103
sevn103
232 satisfied customers
Air conditioner on international 4700 with dt530 engine will
Air conditioner on international 4700 with dt530 engine will run for about 5 min ok the it quits and when the engine is turned off and restarted it will work again for about 5 min then quit what is th… read more
sevn103
sevn103
232 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Daniel Wilson

Daniel Wilson

6,062 satisfied customers

Owner at DJ Wilson

Cat Man

Cat Man

Cat Engine Expert

5,353 satisfied customers

I am ASE Master Truck Certified.

Wayne

Wayne

Journeyman

5,115 satisfied customers

worked on, Gmc, Macks, Freight liner,Mercedes Benz,,Ford, sterling

Jeremy

Jeremy

Certified Truck/Bus Technician

2,756 satisfied customers

ASE Med/HD Truck Technician, NATEF Diesel Engines and Electrical/Electronics Technician, Network Engineer specializing in CAN faults, Aftertertreatment, and vehicle communications

Curtis B.

Curtis B.

Technician

1,947 satisfied customers

Technician turned service manager on multiple lines of trucks and engines, used in industry.

cumminsdr

cumminsdr

Mechanic

1,886 satisfied customers

All types of Cummins applications

Chris (aka-Moose)

Chris (aka-Moose)

Technician

641 satisfied customers

24 years of experience diagnosing & repairing

< Previous | Next >

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x