Medium and Heavy Trucks

Have truck repair questions? Ask an Expert

Connect one-on-one with {0} who will answer your question

This answer was rated:

I have a 11-97 M11 engine # 34889443 engine, cracked block.

I have a 11-97...

I have a 11-97 M11 engine # 34889443 engine, cracked block. Lookin to swap complete. Located a 11-94 m11 eng # 34753763. Assume it's not a direct swap, but more worried about wiring harness then mounting.

Mechanic's Assistant: What is the complete model and serial number of your machine?

8100 international. Vin 1HSHCAHRXXH611613

Mechanic's Assistant: Anything else you want the equipment mechanic to know before I connect you?

Any other issues with swap

Show More
Show Less
Ask Your Own Medium and Heavy Trucks Question
Answered in 16 minutes by:
7/25/2018
Technician: cumminsdr, Mechanic replied 4 years ago
cumminsdr
cumminsdr, Mechanic
Category: Medium and Heavy Trucks
Satisfied Customers: 4,476
Experience: All types of Cummins applications
Verified

You are correct you cannot swap a celect Plus engine (34889443)with a celect engine (34753763). The electronics are not the same. You need to reblock the engine and build it correctly / find a celect plus engine or it will never work right. You are trying to go backwards with engines The flywheel housings would need to be replaced or swapped if it fits properly. A celect engine is the basic like 1 gen electronic engine and you have a celect plus with a bad block that is a newer electronic engine. Even the IH connectors and wiring will not work. Please take a moment to Rate/Accept my service

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 4 years ago
Found another that I think will work. Engine # 34860769. 5-97
Could u verify please, thanks
Technician: cumminsdr, Mechanic replied 4 years ago

34860769 is a celect plus engine you should have no problems swapping. May need to transfer engine mounts over and a few other items as needed. Should swap ecm's or take both to Cummins and transfer data/update to the swap and keep the old one for a spare. Please take a moment to Rate/Accept my service. Thank You

cumminsdr
cumminsdr, Mechanic
Category: Medium and Heavy Trucks
Satisfied Customers: 4,476
Experience: All types of Cummins applications
Verified
cumminsdr and 87 other Medium and Heavy Trucks Specialists are ready to help you
Ask your own question now
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a technicianLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask cumminsdr Your Own Question
cumminsdr
cumminsdr
cumminsdr, Mechanic
Category: Medium and Heavy Trucks
Satisfied Customers: 4,476
4,476 Satisfied Customers
Experience: All types of Cummins applications

cumminsdr is online now

Related Medium and Heavy Trucks Questions
Doing an engine swap in a 2008 International 4300 vin
Doing an engine swap in a 2008 International 4300 vin ***************** with an engine from a 2002 international 4300 1HTMAAM43H571464 would it work with the 08 wiring harness?… read more
Alex Olsen
Alex Olsen
auto/diesel/industrial
746 satisfied customers
I am installing Jacobs engine brakes on a 1995 International
i am installing Jacobs engine brakes on a 1995 International 8100 with a Cummins M11 Celect system. I am looking for the wire numbers in the dash the switches connect into. … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
I have 1 2003 International 7500 with a DT466 motor that is
I have 1 2003 International 7500 with a DT466 motor that is worn out and I also have an 2001 International 4900 with a good 530 engine. Can I iuse the 2001 engine in the 2003 truck … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
Can i swap a1998 m11 cummings engine, for a. I got m11
i got m11 serial #34859448 motor, can i swap for ISM year 2000 serial # 34989751 … read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
5,115 satisfied customers
I tried this earlier but you switched me to sign up. But I
I tried this earlier but you switched me to sign up. But I would like to know how much it costs to ask a mechanic a question … read more
Andy
Andy
truck /coach technician
Vocational, Technical or Trade School
214 satisfied customers
1997 kenworth t800 with Cummins m11. Bought truck found for
1997 kenworth t800 with Cummins m11. Bought truck found for unknown reason the owner swapped out the instrument levers on the right side … read more
cumminsdr
cumminsdr
Mechanic
High School or GED
4,476 satisfied customers
It will crank but not start I checked all the fuses. Its not
it will crank but not start I checked all the fuses … read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
5,115 satisfied customers
I have a 2000 international 8100. Ac compressor not turning
I have a 2000 international 8100. Ac compressor not turning on. … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
I need the elec. schematic for 1994 international 8100
I need the elec. schematic for 1994 international 8100 spcificly the starting diag with a cummins m11 in it … read more
Andy
Andy
truck /coach technician
Vocational, Technical or Trade School
214 satisfied customers
Truck runs well for different amounts of time then won't rev
truck runs well for different amounts of time then won't rev much over idle when trying to get off road starts lurching idles fine Has codes 190 engine speed data eratic and 251Power supply low … read more
Andy
Andy
truck /coach technician
Vocational, Technical or Trade School
214 satisfied customers
2007 FREIGHTliner century class. turns over but will not
2007 FREIGHTliner century class. turns over but will not start. vin number 1fujbbck07pu33562. have two fault codes on dash. one is (eng Controller NoRESP 128s254 07) and the other is ( Brake OPEN 136s… read more
Jeremy
Jeremy
Certified Truck/Bus Technician
Associate Degree
2,756 satisfied customers
I have a 1999 international 8100 the dash cluster is not
i have a 1999 international 8100 the dash cluster is not working there is no communication with a scan tool and the dash cluster is not working it sweeps but shows no info i hope its a ground or wirin… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
My name is ***** ***** Downard. I'm trying to find a wiring
My name is ***** ***** Downard. I'm trying to find a wiring schematic for a 1999 IH 8100 with Cummins M11 engine. I've pulled a Rockwell 10 speed transmission and replaced it with an Allison HD4560P. … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
M11 ***** ***** , truck sat months ,,, changed fuel
truck sat for 5 months ,,, changed fuel filter,chased fuel lines ,blew back in tanks ,pressured the tanks ,no restrictions , truck runs after filter refill and starting fluid, only at high rmp . will not run at an idle.......... is there a filter in the pump ?? or do you want money first ?? … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
Mr. Spanky I am working on a Cummins ISB 2000 year.
Hello Mr. Spanky I am working on a Cummins ISB 2000 year. serial no 46014547, it has the following fault codes ACTIVE Pid 94 fmi 0 water in fuel indicator (no water in filter) sid 237 fmi 11 start ena… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
6,062 satisfied customers
I have a 96 8100 international with m11 cummins and the speedo
I have a 96 8100 international with m11 cummins and the speedo and tach wont work. Just installed new circuit board from international still nothing. im showing engine speed and vehicle speed through … read more
Geoff
Geoff
BS
12 satisfied customers
Reference 1999 M11 select plus CumminsWhat is the voltage
Reference 1999 M11 select plus Cummins What is the voltage on the idle validation switch the throttle position centre… read more
FIX-IT
FIX-IT
Comercial transport technician
Vocational, Technical or Trade Scho
829 satisfied customers
The turbo on my 95 International with a Cummins M11 is beginning
The turbo on my 95 International with a Cummins M11 is beginning to weep a bit of oil around the hose going out to the intercooler. The turbo is a Cummins HX50 p/n(NNN) NNN-NNNNX. I found a new HX55 f… read more
cumminsdr
cumminsdr
Mechanic
High School or GED
4,476 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Daniel Wilson

Daniel Wilson

6,062 satisfied customers

Owner at DJ Wilson

Cat Man

Cat Man

Cat Engine Expert

5,353 satisfied customers

I am ASE Master Truck Certified.

Wayne

Wayne

Journeyman

5,115 satisfied customers

worked on, Gmc, Macks, Freight liner,Mercedes Benz,,Ford, sterling

Jeremy

Jeremy

Certified Truck/Bus Technician

2,756 satisfied customers

ASE Med/HD Truck Technician, NATEF Diesel Engines and Electrical/Electronics Technician, Network Engineer specializing in CAN faults, Aftertertreatment, and vehicle communications

Curtis B.

Curtis B.

Technician

1,947 satisfied customers

Technician turned service manager on multiple lines of trucks and engines, used in industry.

cumminsdr

cumminsdr

Mechanic

4,476 satisfied customers

All types of Cummins applications

Chris (aka-Moose)

Chris (aka-Moose)

Technician

641 satisfied customers

24 years of experience diagnosing & repairing

< Previous | Next >

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x