Medium and Heavy Trucks

Have truck repair questions? Ask an Expert

Ask an Expert,
Get an Answer ASAP!

2006 IHC 9400i showing a fault code 128F01 PID103_A and

Customer Question
2006 IHC 9400i showing...

2006 IHC 9400i showing a fault code 128F01 PID103_A and Cummins Tech Support says it is not their code

Mechanic's Assistant: What is the complete model and serial number of your machine?

9400i and SN 2HSCNAPR96C331144

Mechanic's Assistant: Are you fixing this yourself? What have you tried so far?

Mechanic checked codes and did not know whar to do

Mechanic's Assistant: Anything else you want the equipment mechanic to know before I connect you?

Speed sensor was recently reset and driver says truck runs good

Submitted: 4 months ago.Category: Medium and Heavy Trucks
Show More
Show Less
Ask Your Own Medium and Heavy Trucks Question
Answered in 7 minutes by:
3/12/2018
Technician: cumminsdr, Mechanic replied 4 months ago
cumminsdr
cumminsdr, Mechanic
Category: Medium and Heavy Trucks
Satisfied Customers: 3,850
Experience: All types of Cummins applications
Verified

Hello the fault is for the Turbo Speed sensor Or the other causes below The Turbo speed sensor is the primary issue that I have seen. Please take a moment to Rate/Accept my service.

This fault can come active any time the key is on and the ECM detects turbocharger speed greater than a calibration limit. This fault can be caused by malfunctions in the following components:

  • Turbocharger speed sensor
  • Engine harness
  • ECM power supply or grounds
  • Electronic vehicle accessories which emit excessive electromagnetic interference.

This fault becomes inactive any time the ECM detects a valid turbocharger speed.

If the fault occurs intermittently:

  • Look for causes of intermittent open circuit or short circuits in the turbocharger speed sensor circuit (including the speed sensor pigtail connector).
  • Look for sources of electronic noise such as poorly installed vehicle electronic components.
  • Make sure the vehicle chassis grounds are in good condition.
  • Make sure the ECM power supply and ground circuits are in good condition and that this power supply is not shared with other vehicle electronics.

CodesReasonEffect

Fault Code: 595
PID(P): P 103
SPN: 103
FMI: 01

Turbocharger Number 1 Speed High - warning level. High turbocharger speed has been detected.

Engine power derate. The ECM uses an estimated turbocharger speed.

Ask Your Own Medium and Heavy Trucks Question
Technician: cumminsdr, Mechanic replied 4 months ago

The turbocharger speed sensor is mounted in the center housing of the turbocharger.4032068 is the part number of the Turbo Speed sensor kit

Ask Your Own Medium and Heavy Trucks Question
Technician: cumminsdr, Mechanic replied 4 months ago

How did you make out?

Ask Your Own Medium and Heavy Trucks Question
Technician: cumminsdr, Mechanic replied 4 months ago

Hello Just following up. Please take a moment to Rate/Accept my service. Thank You

Ask Your Own Medium and Heavy Trucks Question
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a technicianLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask cumminsdr Your Own Question
cumminsdr
cumminsdr
cumminsdr, Mechanic
Category: Medium and Heavy Trucks
Satisfied Customers: 3,850
3,850 Satisfied Customers
Experience: All types of Cummins applications

cumminsdr is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Daniel Wilson

Daniel Wilson

2,775 satisfied customers

Owner at DJ Wilson

Cat Man

Cat Man

Cat Engine Expert

4,493 satisfied customers

I am ASE Master Truck Certified.

Wayne

Wayne

Journeyman

2,869 satisfied customers

worked on, Gmc, Macks, Freight liner,Mercedes Benz,,Ford, sterling

Jeremy

Jeremy

Certified Truck/Bus Technician

2,235 satisfied customers

ASE Med/HD Truck Technician, NATEF Diesel Engines and Electrical/Electronics Technician, EPA 608/609 HVAC Certified, Steering/Suspension and ABS/Brakes Technician

cumminsdr

cumminsdr

Mechanic

3,850 satisfied customers

All types of Cummins applications

Curtis B.

Curtis B.

Technician

961 satisfied customers

Technician turned service manager on multiple lines of trucks and engines, used in industry.

dieseldan55

dieseldan55

Contractor

74 satisfied customers

Road Service mechanic for Volvo Construction.

< Previous | Next >

Related Medium and Heavy Trucks Questions
I have a 2012 Ram 3599 with a cummins diesel. Check engine
Hi I have a 2012 Ram 3599 with a cummins diesel. Check engine light is steady on and shows error codes P2509, P013A, P2196 and P2BAC. ANy idea what would cause all four or those codes? … read more
Steven
Steven
Triage Tech/Shop Foreman
Associates
11 satisfied customers
Checking AC 2006 IH 9400i where is relay for compresser in
Checking AC 2006 IH 9400i where is relay for compresser in fuse box there is no location diagram … read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
Looses power uphill & heats up no codes. 2007 international
Looses power uphill & heats up no codes. JA: What's the make/model/year of your truck? Engine type? Customer: 2007 international 9400i 450 isx Cummins JA: Are you fixing your truck yourself? What have… read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
I have 2008 mitsubishi fuso 260 and the check engine light
I have 2008 mitsubishi fuso 260 and the check engine light come on amber first then went to red I stop the truck and tried the reg process, and the light will not go out. … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
2005 is stop engine light staring on no codes shown that
2005 is stop engine light staring on no codes shown that would cause this … read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
2,869 satisfied customers
I have a cummins engine QSB 6.7. When connecting with
When connecting with Cummins insite, it is giving me the following errors 3712 active (RED) … read more
FIX-IT
FIX-IT
Comercial transport technician
Vocational, Technical or Trade Scho
784 satisfied customers
2002 ihc w/dt530. check engine light comes on around 1500
2002 ihc w/dt530. check engine light comes on around 1500 rpm in high gear.(9 speed tranny) occasionally in 8th. when pulling, not even a heavy pull. no smoke or missing, it just powers down … read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
I have a 2005 International 9400i last 8 of VIN is 5c010795.
I have a 2005 International 9400i last 8 of VIN is 5c010795. Fault code on odometer readout is 136F 14 SID254_A. W … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
The pressure gauge is above the normal pressure fault code
The pressure gauge is above the normal pressure fault code shows 128:f02 … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
We have a 2006 9400i series International with an ISX
We have a 2006 9400i series International with an ISX Cummins. There is no throttle response until we get to 25 mph. Then it takes off and runs fine. We had a code of SID 230-4 FMI 4 for idle validati… read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
2,869 satisfied customers
I got a 2012 kenworth with a cummins isx engine. truck wont
i got a 2012 kenworth with a cummins isx engine. truck wont regen while driving and i did a parked regen will not stop or complete regen… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
2009 international prostar vin #2HSCUAPR89C092581AND 2010
2009 international prostar vin #2HSCUAPR89C092581AND 2010 international prostar vin#3HSCUAPROAN210710 cab swap. So what I have is these two truck one damage cab and one with bad motor. 2009 was bad mo… read more
Alex Olsen
Alex Olsen
auto/diesel/industrial
488 satisfied customers
2007 International 9400i with cummins ISX. Last week check
2007 International 9400i with cummins ISX. Last week check engine light kept coming on and off and truck would lose power and wont go above 55MPH. Today the truck wont go over 35MPH and is throwing th… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
2009 ihc 4300 truck clearance and dash lights stay on.Only
2009 ihc 4300 truck clearance and dash lights stay on. Only way to shut off is disconnect battery… read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
I have a Cummins ISM eng #35253921. I am getting a DTC 2639.
I have a Cummins ISM eng #35253921. I am getting a DTC 2639. Refers to the differential pressure being out of range. This truck has a freshly cleaned DPF, egr, and egr cooler. With the truck running o… read more
cumminsdr
cumminsdr
Mechanic
3,850 satisfied customers
Heavy Duty Truck 08 IH 584588 Miles VIN 2H5CEAHR78C680143 Cummins
Heavy Duty Truck 08 IH 584588 Miles VIN 2H5CEAHR78C680143 Cummins Engine - Mod ISM410 - Engine SN 35207517 Complaint - Loss of power & warning light is on. Using Cummins software - had codes 2638 & 19… read more
Geoff
Geoff
BS
8 satisfied customers
We have a 2010 Kenworth T660 with a Cummins ISX 450. It is
We have a 2010 Kenworth T660 with a Cummins ISX 450. It is a former Conway fleet truck. According to the Cummins techs when we plugged to the computer, the engine is running like a top, not a code to … read more
cumminsdr
cumminsdr
Mechanic
3,850 satisfied customers
222mk, 2007 International 4300 s/a truck- Servicemaxx-
2007 International 4300 s/a truck- Servicemaxx- I am trying to reprogram the computerto reset the tire revs, and lower cc that all works till I get ot the save part and then it needs a customer passwo… read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x