Medium and Heavy Trucks

Have truck repair questions? Ask an Expert

Connect one-on-one with {0} who will answer your question

This answer was rated:

Have 2 fault codes on 09 fl volvo first one is ppid 270

Hi Dan have 2 fault...
Hi Dan have 2 fault codes on 09 fl volvo first one is ppid 270 second one is psid 46 thanks
Show More
Show Less
Ask Your Own Medium and Heavy Trucks Question
Answered in 5 hours by:
2/15/2018
Technician: Daniel Wilson,
 replied 4 years ago
Daniel Wilson
Category: Medium and Heavy Trucks
Satisfied Customers: 14,855
Experience: Owner at DJ Wilson
Verified

Good morning, I will look those up for you. What model is this? D12, D13, etc?

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 4 years ago
Not sure what model dan it's small volvo 18 tonne lorry
Technician: Daniel Wilson,
 replied 4 years ago

ECM SPN 3226, Aftertreatment Outlet NOx – MID 128 PPID 270/ PSID 90

The individual FMI numbers associated with this fault are listed below:
FMI Description: Fault Condition: Possible
Symptoms:
Possible Cause
FMI 2 • Data erratic,
intermittent or
incorrect
• Inlet NOx sensor
error (plausibility)
• Mismatch
between sensors
• MIL illuminated • Engine out NOx high
• Faulty NOx sensor
• Aftertreatment Diesel Exhaust Fluid
(DEF) quality
FMI 3 • Voltage above
normal or shorted
to high source
• Short Circuit, NOx
signal
• MIL illuminated • Faulty wiring between NOx sensor and
NOx sensor ECU
• Faulty NOx sensor
FMI 5 • Current below
normal or open
circuit
• Open Circuit, NOx
signal
• MIL illuminated • Faulty wiring between NOx sensor and
NOx sensor ECU
• Faulty NOx sensor
54

FMI 9 • Abnormal update
rate
• Missing signal
from NOx sensor
• MIL illuminated
• Yellow Check lamp
illuminated
• Loss of communication from NOx
sensor ECU and Engine Control
Module (ECM)
FMI 11 • Root cause not
known
• NOx sensor
measures near
zero for long time
with high load
• MIL illuminated • Faulty NOx sensor
FMI 12 • Bad intelligent
device or
component
• NOx-sensor signal
corrupt (incorrect
value)
• MIL illuminated • Faulty NOx sensor
FMI 13 • Out of calibration • NOx-sensor
activation
(incorrect value)
• MIL illuminated • Faulty NOx sensor
FMI 14 • Special instructions • Missing signal
from sensor due to
battery voltage
• MIL illuminated • Voltage to NOx sensor is too high or
too low
• Faulty harness to sensor
FMI 31 • Condition exists • Inlet NOx sensor
error
• Mismatch
between sensors
• MIL illuminated • Engine out NOx high
• Faulty NOx sensor
• Aftertreatment Diesel Exhaust Fluid

See if you can get the FMI number after the fault. It will narrow down whether open circuit, short, etc.

Ask Your Own Medium and Heavy Trucks Question
Technician: Daniel Wilson,
 replied 4 years ago

ECM SPN 5246, Aftertreatment SCR Operator Inducement Severity – MID
128 PSID 46

FMI 0 • Data valid but above
normal operational
range - Most severe
level
• Severe SCR
system fault
detected –
Warning fault
• Severe engine
derate
• N/A
FMI 15 • Data valid but above
normal operating
range - Least severe
level
• Moderate SCR
system fault
detected –
Warning fault
• Moderate engine
derate
• N/A
FMI 16 • Data valid but above
normal operating
range - Moderately
severe level
• SCR system
fault detected –
Warning fault
• Engine derate • N/A

The last one is an informational fault as listed resulting from the NOX fault. correct the NOX fault and run a successful regen to reset the system. sometimes the software itself needs to be reset in the ECM if a regen wont reset it.

Please take a moment to rate as that is how the site credits my time helping on the site or let me know if you need more help. 5 star and bonuses are always greatly appreciated.

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 4 years ago
Sorry for delay dan will be tomorow before I can get other codes thanks
Technician: Daniel Wilson,
 replied 4 years ago

No worries. We can follow up as needed.

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 4 years ago
Hi Dan sorry took so link them faults are fmi 13 and fmi*****to clear the faults without diagnostic as it's gone into engine derate my laptop won't connect to it
Technician: Daniel Wilson,
 replied 4 years ago
The Faults cannot be cleared until the repairs are made. Only inactive faults can be cleared. If repairs have been made but the faults won't reset after a successful regeneration, you will need the Volvo diagnostic software to reset the ECM software.In some cases it needs to be reflashed and updated to the latest version and updates
Ask Your Own Medium and Heavy Trucks Question
Technician: Daniel Wilson,
 replied 4 years ago

Hi, Did you get this resolved? Please take a moment to rate as that is how the site credits my time helping on the site or let me know if you need more help. 5 star and bonuses are always greatly appreciated.

Daniel Wilson
Category: Medium and Heavy Trucks
Satisfied Customers: 14,855
Experience: Owner at DJ Wilson
Verified
Daniel Wilson and 87 other Medium and Heavy Trucks Specialists are ready to help you
Ask your own question now
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a technicianLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask Daniel Wilson Your Own Question
Daniel Wilson
Daniel Wilson
Daniel Wilson
Category: Medium and Heavy Trucks
Satisfied Customers: 14,855
14,855 Satisfied Customers
Experience: Owner at DJ Wilson

Daniel Wilson is online now

Related Medium and Heavy Trucks Questions
IT A BIG RIG. Its a 2012 Volvo 780. 1,234,567 miles d13
IT A BIG RIG JA: What's the make, model, and year of your car? Customer: its a 2012 Volvo 780 JA: What's the approximate mileage on your 2012 Volvo 780? Customer: 1,234,567 miles d13 engine JA: Is the… read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
Mack CXU 613 MID 128 PPID 270 FMI 12. How I could be sure
Hi! Mack CXU 613 MID 128 PPID 270 FMI 12. How I could be sure it's inlet or outlet NOX? Thanks! … read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
5,115 satisfied customers
For mcmilan only i have 2013 volvo isx15 with message "ecu
for mike mcmilan only i have 2013 volvo isx15 with message "ecu maintanance" can you help with that message not sure what it is… read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
My truck just brake down now and I need assistance from
My truck just brake down now and I need assistance from technician please … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
2016 VNL 780 D13 Recently replaced egr cooler, egr delta p
2016 VNL 780 D13 Recently replaced egr cooler, egr delta p sensor, and def injector. Extremely Poor fuel economyGetting SPN 5357 FMI 17 SPN 3216 FMI 12 SPN 3226 FMI 20… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
14,855 satisfied customers
Truck keep on shutting off. We have a fault code mid 128
Truck keep on shutting off JA: Sometimes things that you think will be really complicated end up being easy to fix. The Heavy Truck Mechanic I'm going to connect you with knows all the tricks and shor… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
14,855 satisfied customers
I have an active abs code 255 on a 08 Peterbilt serial
Hi I have an active abs code 255 on a 08 Peterbilt serial number 775712. It's a Bendix EC-60 system. There's no description or troubleshooting info on it, do you have any?… read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
SPN 3216. MID 128 348. WE INSTALLED A NOX SENSOR. STILL HAVE
SPN 3216. MID 128 348. WE INSTALLED A NOX SENSOR. STILL HAVE A CHECK ENGINE LIGHT ...2 CODES … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
I have a 2012 volvo D13. I have a 2012 volvo D13. I was
i was trying my mechanic fix a leak but nothing happenes this is what my truck is doing: my volvo is automatic when i put it in N (neutral) you can hear when you give gas to the truck … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
2010 mack chu 613 PSID 46 FMI 0 and PPID 270 FMI 9. 2010
2010 mack chu 613 PSID 46 FMI 0 and PPID 270 FMI 9 … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
I have a 2007 Volvo VNL VIN:4V4NC9GH47N396951 with a no
i have a 2007 Volvo VNL VIN:4V4NC9GH47N396951 with a no start condition. engine turns over, but no start. oil level is full, engine harness connectors are clean and free off damaged pins, same on the … read more
Mike Mcmillan
Mike Mcmillan
Triage Tech/Shop Foreman
Associates
591 satisfied customers
Could you help me with some volvo fault codes mid 136 psid
Hi Daniel could you help me with some volvo fault codes mid 136 psid 23 Mid 136 sid 3 Mid 130 psid 204… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
14,855 satisfied customers
I have code SPN 5246 FMI 0 on my Volvo D13H 2011 256k miles.
Second opinion] I have code SPN 5246 FMI 0 on my Volvo D13H 2011 256k miles. It says DEF tank low Derate to 5 mph, but my DEF tank is full. I can't clear this code and Tech Tool isn't much help in my … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
14,855 satisfied customers
I have a 2009 freightliner Columbia vin #1fuja6ck69lam6313
I have a 2009 freightliner Columbia vin #1fuja6ck69lam6313 It is not going into gear it an automatic transmission and is reading an code ECU 130 … read more
spankyjr1
spankyjr1
Retired
Vocational, Technical or Trade Scho
420 satisfied customers
2009 mack pinnacle chu613. Started up like any other day, it
2009 mack pinnacle chu613. Started up like any other day, it ran for about 2 minutes and die. It cranks but won't start. I tried little ether it runs but won't stay running.… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
14,855 satisfied customers
Mid 216 psid 201 fmi 9.....one low beam headlight is out and
Hi Dan, Mid 216 psid 201 fmi 9.....one low beam headlight is out and all the parking/running lights are out...please help.… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
14,855 satisfied customers
I have a 2012 Mack in the shop now with misc DEF codes in it
I have a 2012 Mack in the shop now with misc DEF codes in it sre you familiar with the system… read more
Geoff
Geoff
BS
12 satisfied customers
I have a 2010 mack cxu 613 with codes MID 128 PPID 326 FMI
I have a 2010 mack cxu 613 with codes MID 128 PPID 326 FMI 11 also had another code MID 128 PPID 270 FMI 5 stop engine light is on and dpf regen light is flashing. We already had the DPF cleaned and w… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
14,855 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Daniel Wilson

Daniel Wilson

14,855 satisfied customers

Owner at DJ Wilson

Cat Man

Cat Man

Cat Engine Expert

5,353 satisfied customers

I am ASE Master Truck Certified.

Wayne

Wayne

Journeyman

5,115 satisfied customers

worked on, Gmc, Macks, Freight liner,Mercedes Benz,,Ford, sterling

Jeremy

Jeremy

Certified Truck/Bus Technician

2,756 satisfied customers

ASE Med/HD Truck Technician, NATEF Diesel Engines and Electrical/Electronics Technician, Network Engineer specializing in CAN faults, Aftertertreatment, and vehicle communications

Curtis B.

Curtis B.

Technician

1,947 satisfied customers

Technician turned service manager on multiple lines of trucks and engines, used in industry.

cumminsdr

cumminsdr

Mechanic

1,886 satisfied customers

All types of Cummins applications

Chris (aka-Moose)

Chris (aka-Moose)

Technician

641 satisfied customers

24 years of experience diagnosing & repairing

< Previous | Next >

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x