Medium and Heavy Trucks

Have truck repair questions? Ask an Expert

Ask an Expert,
Get an Answer ASAP!

This answer was rated:

I hav a 2008 Freighliner MT55 chasis. 6.7 cumin diesel. I…

Hi there I hav a...
Hi there I hav a 2008 Freighliner MT55 chasis. 6.7 cumin diesel. I replacing the front brake rotors I removed the hug with wheel bearing. Now I'm installing I hav to tigh the 2 nut. There's 2 washer between the 2 nuts. I need the torque specific
Show More
Show Less
Ask Your Own Medium and Heavy Trucks Question
Answered in 4 hours by:
8/20/2017
go-west..
go-west.., Technician
Category: Medium and Heavy Trucks
Satisfied Customers: 1,266
Experience: Technican with 20 years experience focused on engines and electrical.
Verified
Good morning
Inner nut spin the hub while turning nut,torque nut to 100 ft lbs, then back off,then tighten to 20 ftlbs, verify 1 to 5 thou end play.. assemble the rest, torque outer nut ( jam nut) to 150 ftlbs bend the lock ring over and your good to go.
Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 11 months ago
Ty. How about the wheel setup nut
You meen the one that goes beside the bearing? (inner)?
Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 11 months ago
I mean the wheel lug nut torque
What socket size are you using?
Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 11 months ago
33mm
450 ft lbs
go-west..
go-west.., Technician
Category: Medium and Heavy Trucks
Satisfied Customers: 1,266
Experience: Technican with 20 years experience focused on engines and electrical.
Verified
go-west.. and 87 other Medium and Heavy Trucks Specialists are ready to help you
Ask your own question now
Customer reply replied 11 months ago
Ty
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a technicianLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask go-west.. Your Own Question
go-west..
go-west..
go-west.., Technician
Category: Medium and Heavy Trucks
Satisfied Customers: 1,266
1,266 Satisfied Customers
Experience: Technican with 20 years experience focused on engines and electrical.

go-west.. is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Daniel Wilson

Daniel Wilson

2,775 satisfied customers

Owner at DJ Wilson

Cat Man

Cat Man

Cat Engine Expert

4,493 satisfied customers

I am ASE Master Truck Certified.

Wayne

Wayne

Journeyman

2,869 satisfied customers

worked on, Gmc, Macks, Freight liner,Mercedes Benz,,Ford, sterling

Jeremy

Jeremy

Certified Truck/Bus Technician

2,235 satisfied customers

ASE Med/HD Truck Technician, NATEF Diesel Engines and Electrical/Electronics Technician, EPA 608/609 HVAC Certified, Steering/Suspension and ABS/Brakes Technician

cumminsdr

cumminsdr

Mechanic

1,337 satisfied customers

All types of Cummins applications

Curtis B.

Curtis B.

Technician

961 satisfied customers

Technician turned service manager on multiple lines of trucks and engines, used in industry.

dieseldan55

dieseldan55

Contractor

74 satisfied customers

Road Service mechanic for Volvo Construction.

< Previous | Next >

Related Medium and Heavy Trucks Questions
Volvo VNL 780. 2017 truck. I need complete step by step
Volvo VNL 780 . 2017 truck . I need complete step by step instruction om cgangibg tge axle seal. Need procedure for bearing tirque and steps pertaining to this truck.Vin # 4V4NC9EJ9HN968264… read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
2,869 satisfied customers
2005 International 4400 7.6 L 466 L6 International DT466
2005 International 4400 7.6 L 466 CID L6 International DT466 Diesel Complete instructions / procedure to install New brake shoes and axle seal passenger side rear of the vehicle… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
I hav a 2011 Isuzu NPR diesel 3.0lt. VIN. JALB4W173B7402017.
Hi there. I hav a 2011 Isuzu NPR diesel 3.0lt. VIN. JALB4W173B7402017. I'm replacing the front brakes pads and rotor. I removed the front wheel bearing hoisin to get the rotor out. Now I'm putting eve… read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
2,869 satisfied customers
I just finished rebuild cat c13 lee10760. The pulley on the
I just finished rebuild cat c13 lee10760 . The pulley on the damper not aligned with fan pulley . What going on ? … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
2009 international prostar no fan on with ac. Vin #
2009 international prostar no fan on with ac. Vin # 2HSCUAPR89C092581. Truck does not turn fan on when a.c. high side pressure rises . Even if it goes to 400. I checked with diamond logic and it sees … read more
Jeremy
Jeremy
Certified Truck/Bus Technician
Associate Degree
2,235 satisfied customers
2002 T2000 KW what is the correct torque for wheel bearing
2002 T2000 KW what is the correct torque for wheel bearing spindle nut in the steer axle the inner nut against bearing and jam nut next to it… read more
Jeremy
Jeremy
Certified Truck/Bus Technician
Associate Degree
2,235 satisfied customers
I need specific instructions on replacing an engine air
I need specific instructions on replacing an engine air brake compressor on a 2008, 6.7 liter Paccar diesel. Is it necessary to put the engine on TDC before removing compressor, if so how do I find TD… read more
cumminsdr
cumminsdr
Mechanic
High School or GED
1,337 satisfied customers
I'm working on a 2001 freightliner with a 8.3litre cummins.
Hi, I'm working on a 2001 freightliner with a 8.3litre cummins. Engine serial number 46102611.The engine runs rough at start up and stalls sometimes, it seems to be putting diesel fuel into the oil pa… read more
cumminsdr
cumminsdr
Mechanic
High School or GED
1,337 satisfied customers
I have a 2008 Freightliner with a ISC 330 Cummins that I
I have a 2008 Freightliner with a ISC 330 Cummins that I want to change the high pressure fuel pump on. is there a timing issue where it has to be on #1 before I remove the old pump and what is the to… read more
cumminsdr
cumminsdr
Mechanic
High School or GED
1,337 satisfied customers
2002 International 4700 7.3L Diesel What are the tightening
2002 International 4700 7.3L Diesel What are the tightening / torque specifications for the front and rear wheel lug nuts?… read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
2,869 satisfied customers
What can allow a tandem wheel on the 4th axle of a semi
what can allow a tandem wheel on the 4th axle of a semi trailer to come free of its attachment?… read more
Jeremy
Jeremy
Certified Truck/Bus Technician
Associate Degree
2,235 satisfied customers
. I just rebuild 09 Detroit ddec 6 but now it starts
I just rebuild 09 Detroit ddec 6 but now it starts injectors working. will not rev up good, takes long time to reach 1500rpm parked can you help?… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
111mk, 1989 international S'1954 with DT466 and Eaton 8LL. The
1989 international S'1954 with DT466 and Eaton 8LL. The truck lurches when you take off from a stop fully loaded. It is a straight truck as well. We just redid the rear motor mounts about 6mo ago. We … read more
John Vieira
John Vieira
Heavy Duty Diesel Mechanic
63 satisfied customers
I need torque specs for cam gear, idler gear connecting rods,
I need torque specs for cam gear, idler gear connecting rods, main bearings fuel pump, vibration damper and cylinder head on 3304 cat SN# *****… read more
catmastertech
catmastertech
Field service technician
Vocational, Technical or Trade Scho
1,287 satisfied customers
I am replacing the camshaft on my 98 series 60 detroit
I am replacing the camshaft on my 98 series 60 detroit engine serial 06R0357227 truck VIN WK950268, I am unable to get any instructions on proper procedure..My guy is a Cat mech and not familar with d… read more
DirectInjection
DirectInjection
Field Service
Diplom
56 satisfied customers
I have a peterbilt 330. Im doing brakes, wheel seals, and
I have a peterbilt 330. I'm doing brakes, wheel seals, and bearings all around. I'm wondering what the torque setup is on the hub nuts when I go back together for both front and rear axle. Thanks for … read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
2,869 satisfied customers
What are the main causes of the front or rear crankshaft seals
What are the main causes of the front or rear crankshaft seals to leak on Detroit Diesel 60 Series?… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,775 satisfied customers
What is the correct torque setting for front hub after
what is the correct torque setting for front hub nut after replacing brake disc on a daf cf 85… read more
Eurotruck72
Eurotruck72
Garage owner
120 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x