Medium and Heavy Trucks

Have truck repair questions? Ask an Expert

Ask an Expert,
Get an Answer ASAP!

2008 dt466 I have a no start condition.I have fuel pressure.

Customer Question
2008 dt466 I...

2008 dt466 I have a no start condition.I have fuel pressure. I have 485-500 psi icp. I have 0 in the desired icp. I am confused on that

Mechanic's Assistant: What's the make/model/year of your truck? Engine type?

2008 IH dt466

Mechanic's Assistant: Are you fixing your truck yourself? What have you tried so far?

The question I need an answer to is why I dont have a desired icp on my scanner. Is this a bad ECM

Submitted: 1 year ago.Category: Medium and Heavy Trucks
Show More
Show Less
Ask Your Own Medium and Heavy Trucks Question
Answered in 20 minutes by:
3/21/2017
Technician: Alex Olsen,
 replied 1 year ago
Alex Olsen
Category: Medium and Heavy Trucks
Satisfied Customers: 236
Experience: Lead technican at Astleford international trucks
Verified

hi im alex, could i get the lat 8 of your vin# *****

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 1 year ago
8j689092
Customer reply replied 1 year ago
OK, I have fuel pressure 60 psi. I have 480-500 psi of icp. No start. MY snap scanner shows 0 in the desired icp block. I have never seen that and I think that is why I have a no start but what is causing that
Customer reply replied 1 year ago
are you there
Technician: Alex Olsen,
 replied 1 year ago

hmm will it run on ether?

Ask Your Own Medium and Heavy Trucks Question
Technician: Alex Olsen,
 replied 1 year ago

its starts and stays running on ether?, does it see RPM?

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 1 year ago
it w run on ether and the scanner sees rpm while cranking
Customer reply replied 1 year ago
if I hook a separate harness to the ipr and put 12 volts to it, the icp will go to 5000 very quickly. which leeds me to believe that the pump is ok
Technician: Alex Olsen,
 replied 1 year ago

ok good yeah i would say the pump is good, so it stays running after you start it on ether?

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 1 year ago
no only till the ether runs out
Technician: Alex Olsen,
 replied 1 year ago

ok, and no codes, usually when the ecm desires no icp it dosen't think it is cranking

Ask Your Own Medium and Heavy Trucks Question
Technician: Alex Olsen,
 replied 1 year ago

make sure the cam sensor and crank sensor are connected and pins are clean

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 1 year ago
crank sensor is working because it is reading RPMs. not sure how to check cam sensor, but no cam sensor codes
Technician: Alex Olsen,
 replied 1 year ago

yep reads rpm off crank, un plug the cam sensor and see if it sets a code

Ask Your Own Medium and Heavy Trucks Question
Customer reply replied 1 year ago
cam sensor is good
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a technicianLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask Daniel Wilson Your Own Question
Daniel Wilson
Daniel Wilson
Daniel Wilson
Category: Medium and Heavy Trucks
Satisfied Customers: 2,825
2,825 Satisfied Customers
Experience: Owner at DJ Wilson

Daniel Wilson is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Daniel Wilson

Daniel Wilson

2,825 satisfied customers

Owner at DJ Wilson

Cat Man

Cat Man

Cat Engine Expert

4,530 satisfied customers

I am ASE Master Truck Certified.

Wayne

Wayne

Journeyman

2,892 satisfied customers

worked on, Gmc, Macks, Freight liner,Mercedes Benz,,Ford, sterling

Jeremy

Jeremy

Certified Truck/Bus Technician

2,243 satisfied customers

ASE Med/HD Truck Technician, NATEF Diesel Engines and Electrical/Electronics Technician, EPA 608/609 HVAC Certified, Steering/Suspension and ABS/Brakes Technician

cumminsdr

cumminsdr

Mechanic

1,351 satisfied customers

All types of Cummins applications

Curtis B.

Curtis B.

Technician

991 satisfied customers

Technician turned service manager on multiple lines of trucks and engines, used in industry.

dieseldan55

dieseldan55

Contractor

74 satisfied customers

Road Service mechanic for Volvo Construction.

< Previous | Next >

Related Medium and Heavy Trucks Questions
I HAVE A IH 3200 BUS WITH 466E 2006 YEAR ,LOSS OF POWER AND
I HAVE A IH 3200 BUS WITH 466E 2006 YEAR ,LOSS OF POWER AND MISS ON #1 CYLINDER REPLACED ALL INJECTORS AND VALVE COVER GASKET,AND PUCKS AND HIGN OIL PRESSURE SENSOR ON OIL RAIL.NO CODES ANY MORE.… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,825 satisfied customers
Matt with MYO Express here. I am having an issue with the
Hello Dan. Matt with MYO Express here. I am having an issue with the same DT466 you helped me with on August 30th. The truck can only be started using ether, or pull started. Once running, the truck w… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,825 satisfied customers
I have a 2007 international with a dt466 and it won't start.
I have a 2007 international with a dt466 and it won't start. I've checked fuel pressure and injection control pressure they are good. What else to check?… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,825 satisfied customers
I have a 2006 International bus VT365. It shut down while
I have a 2006 International bus VT365. It shut down while driving and it wont start. I found that it didn't have low oil pressure. I checked the oil level and found that it was very low. I added oil a… read more
Jeremy
Jeremy
Certified Truck/Bus Technician
Associate Degree
2,243 satisfied customers
I have a 2001 International DT466 Vin#********. The engine
Hi I have a 2001 International DT466 Vin#********. The engine stalls intermittely and I started right back but now is not starting. it is not even cranking and when I connected the scanner I found tha… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,825 satisfied customers
I have a 2000 F650 with a 7.2L cat. No start condition. No
I have a 2000 F650 with a 7.2L cat. No start condition. No fault code, cranking rpm 215, icp is 145psi while cranking, starts and runs on wd40, icp goes up to 1300psi. Engine oil level is good and eng… read more
Cat Man
Cat Man
Cat Engine Expert
Vocational, Technical or Trade Scho
4,530 satisfied customers
Dt466 died on the road won't restart check engine came on
dt466 died on the road won't restart check engine came on for a second replaced ipr still no start will run on either but won't continue to run… read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
2,892 satisfied customers
I have a 2006 international 4300 DT466 engine vin 1htmmaam67h358764.
I have a 2006 international 4300 DT466 engine vin 1htmmaam67h358764. It has rough idle after warm up. Checked icp it is very irratic mostly ranges from 620-700 but it will drop to low 500s at idle.No … read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
I have a 2003 International 4300 DT466. getting code
Hello I have a 2003 International 4300 DT466. getting code 333 under hard acceleration. Have changed oil and filter, all new injectors and IPR valve with new pigtail. Using ServiceMaxx software with N… read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
I have a 02 International 4300 dt466 had to replace front and
I have a 02 International 4300 dt466 had to replace front and rear timing cover, So disassembled the front and had to remove cam unable to pull gear off of camshaft so I pulled head and then puu1lled … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,825 satisfied customers
2004 international 4400 with dt466. Runs rough and white smokes.
2004 international 4400 with dt466. Runs rough and white smokes. Fuel pressure shows 60psi at idle. Icu pressure actual and desired match. It will fail all cylinders on a cylinder contribution test. I… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,825 satisfied customers
I have a 2005 international 4300 with dt466. Problem with stalling
I have a 2005 international 4300 with dt466. Problem with stalling while driving. shuts down and starts back up again. Finally stalled an won't start again.… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
2,825 satisfied customers
My truck died. Scanner said oil pressure switch. Replaced it
My truck died. Scanner said oil pressure switch. Replaced it no run scanner said icp. Have not replaced that. Checked fuel pressure 60 psi. Oil 60 psi. high pressure pump is next I don't know what pre… read more
Jeremy
Jeremy
Certified Truck/Bus Technician
Associate Degree
2,243 satisfied customers
have a 97 dt466 wont start gauges cycle 60psi fuel 875 psi
have a 97 dt466 wont start gauges cycle 60psi fuel 875 psi on icp while cranking engine makes no dif with icp unplugged never mind I figured it out bad relay… read more
Expert
Expert
international 4300: 2006 International DT466 EGR engine has
2006 International DT466 EGR engine has crank no start. ICP pressure jumps around from 60/280 to sometimes 720 but no start. Has fuel pressure at 55 PSI. No high pressure oil leaks. Resealed oil rail … read more
Andy3221
Andy3221
truck /coach technician
Vocational, Technical or Trade Scho
222 satisfied customers
02 DT466 WHAT IS THE MIN PRESSURE TO START WHILE CRANKING OVER
02 DT466 WHAT IS THE MIN PRESSURE TO START WHILE CRANKING OVER ON THE HEUI PUMP AND MECHANICAL FUEL PUMP… read more
Cat Man
Cat Man
Cat Engine Expert
Vocational, Technical or Trade Scho
4,530 satisfied customers
i hav 03 dt466 that has intermidet low power while driving
i hav 03 dt466 that has intermidet low power while driving when there is a power low icp drops to about 1200 psi could it be icp ipr or high pressure oil pump. thanks for any help!… read more
Cat Man
Cat Man
Cat Engine Expert
Vocational, Technical or Trade Scho
4,530 satisfied customers
I am working on a 2005 IH 4300 w/DT466 , also having similar
I am working on a 2005 IH 4300 w/DT466 , also having similar problems. The truck started off w/ problem of stalling sometimes when hot. No codes & starts back up. I replaced cam sensor , worked ok for… read more
diesel-tech
diesel-tech
Owner of landrys truck repair llc
130 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x