How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Wayne Your Own Question
Wayne
Wayne, Journeyman
Category: Medium and Heavy Trucks
Satisfied Customers: 9817
Experience:  worked on, Gmc, Macks, Freight liner,Mercedes Benz,,Ford, sterling
6825259
Type Your Medium and Heavy Trucks Question Here...
Wayne is online now
A new question is answered every 9 seconds

I have a '94 Topkick C-6000 with hydraulic brake problems.

Customer Question

I have a '94 Topkick C-6000 with hydraulic brake problems. Warning lights on park brake & Aux. brake been on and now brake system "locked up". Read online how to check codes on black box. Codes are: 1, 2, 3, 13, 14, & 50. Looking for problems indicated for these numbers.
Either you can translate code or direct me to manuals.
Gary
Submitted: 1 year ago.
Category: Medium and Heavy Trucks
Expert:  Wayne replied 1 year ago.

Hi I'm Wayne

I will help you with this

see if this helps you

code - code definition
12- diagnostic mode
13- 02 sensor or circuit
14- coolant sensor or circuit/ high temp indicated
15- coolant sensor or circuit/ low temp indicated
16- system voltage out of range
19- crankshaft position sensor or circuit
21- throttle position sensor or circuit- voltage high
22- throttle position sensor or circuit- voltage low
23- mixture control (m/c) solenoid or circuit (carbureted models)
23- manifold air temperature (mat) sensor or circuit (1990 and earlier models)
23- intake air temperature (iat) sensor circuit (fuel-injected models)
24- vehicle speed sensor (vss) or circuit 25- manifold air temperature (mat) sensor or circuit - high temperature indicated (1990 and earlier models) 25- intake air temperature (iat) sensor or circuit - high temperature indicated (1991 and later models) 26- quad driver module circuit 27- quad driver module circuit 28- quad driver module circuit 29- quad driver module circuit 31- park/neutral position (pnp) switch circuit 32- baro sensor or circuit (carbureted models) 32- egr circuit (fuel-injected models) 33- manifold absolute pressure (map sensor signal voltage high 33- mass air flow (maf) sensor or circuit - excessive airflow indicated 34- manifold absolute pressure (map) sensor signal voltage low 34- mass air flow (maf) sensor signal - low airflow indicated 35- idle speed control (isc) switch or circuit (shorted) (carbureted models) 35- idle air control (iac) valve/ circuit 38- brake switch circuit 39- torque converter clutch (tcc) circuit 41- no distributor signals to ecm, or faulty ignition module ( carbed models) 41- cylinders select error- mem-cal or ecm problem ( fuel-injected models 41- cam sensor circuit (3.8 engine) 42- bypass or electronic spark timing (est) circuit 43- low voltage at ecm terminal l (carbureted models) 43- knock sensor circuit 44- oxygen sensor or circuit - lean exhaust detected 45- oxygen sensor or circuit - rich exhaust detected 46- power steering pressure switch circuit 48- misfire diagnosis 51- prom, mem-cal or ecm problem 52- calpak or ecm problem 53- egr fault (carbureted models only) 53- system over-voltage (ecm over 17.7 volts) 54- mixture control (m/c) solenoid or circuit (carbureted models) 54- fuel pump circuit (1986 and later models) 55- oxygen sensor circuit or ecm 55- fuel lean monitor (2.2l engine) 61- oxygen sensor signal faulty (possible contaminated sensor) 62- transaxle gear switch signal circuits 63- manifold absolute pressure (map) sensor voltage high (low vacuum detected) 64- manifold absolute pressure (map) sensor voltage low (high vacuum detected) 66- pressure sensor or circuit air conditioning

Hope this helped you

Customer: replied 1 year ago.
Thank you ... Account question : How do I sign up for monthly plans. Been trying to find how to go back to listings of monthly options
Expert:  Wayne replied 1 year ago.

Hi

You can contact customer***@******.***

or

***@******.***

Please remember to rate my answer if this helped you

Expert:  Wayne replied 1 year ago.

Hi

I'm just following up with you

did my answer help you

let me know ,Please

Wayne

Expert:  Wayne replied 1 year ago.

Hi

Just following up with you

did my answer help you

Let me know ,Please