How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask roybelding Your Own Question
roybelding
roybelding, Shop Foreman Freightliner trucks
Category: Medium and Heavy Trucks
Satisfied Customers: 6191
Experience:  Shop Froeman for Freightliner Trucks
3506196
Type Your Medium and Heavy Trucks Question Here...
roybelding is online now
A new question is answered every 9 seconds

2011cordoba frightliner de rate code EEC 061 spn004354 line

Customer Question

2011cordoba frightliner de rate code EEC 061 spn004354 line heat 1 05 can you tell me what this code is refering to and can I fix this proble myself thank you Darry
Submitted: 1 year ago.
Category: Medium and Heavy Trucks
Expert:  roybelding replied 1 year ago.

good evening my name is ***** ***** I will assist

it sounds like you may have a knock sensor that is not working. I will post the flow chart for you to follow.

Roy

SPN 4364/FMI 1 - EPA10

Selective Catalyst Reduction NOx Conversion Very Low

SPN 4364/FMI 1

DescriptionThis fault code sets when the Aftertreatment Control Module (ACM) detects that the NOx conversion is lower than a calibrated threshold

Monitored ParameterSelective Catalyst Reduction (SCR) Inlet NOx sensor, SCR outlet NOx sensor

Typical Enabling ConditionsDiesel Exhaust Fluid (DEF) dosing enabled, 1000 - 1500 rpm, 15 - 100% load, SCR inlet temperature sensor less than 650°C (1200°F), ambient temperature greater than 0°C (32°F), coolant temperature greater than 70°C (158°F), non-regeneration conditions present

Monitor SequenceNone

Execution FrequencyContinuous when enabling conditions met

Typical Duration30 Minutes

Dash LampsMIL

Engine ReactionDerate 25%

VerificationParked Regeneration

Show/Hide Checkboxes

NOTE: SPN 3361/FMI 5 will set when the DEF dosing valve electrical connector is disconnected. The fault code can be cleared using DiagnosticLink after the DEF dosing valve electrical connector is reconnected.

ENGINE EXHAUST

To avoid injury from inhaling engine exhaust, always operate the engine in a well-ventilated area. Engine exhaust is toxic.

HOT EXHAUST

During parked regeneration the exhaust gases will be extremely HOT and could cause a fire if directed at combustible materials. The vehicle must be parked outside.

PERSONAL INJURY

To avoid injury before starting and running the engine, ensure the vehicle is parked on a level surface, parking brake is set, and the wheels are blocked.

ENGINE EXHAUST

To avoid injury from inhaling engine exhaust, always operate the engine in a well-ventilated area. Engine exhaust is toxic.

PERSONAL INJURY

To avoid injury before starting and running the engine, ensure the vehicle is parked on a level surface, parking brake is set, and the wheels are blocked.

  1. Connect DiagnosticLink® .
  2. Turn the ignition ON (key ON, engine OFF).
  3. Was another emission component-related fault code repaired prior to this step?
    1. Yes; perform a parked regeneration and recheck for the fault code. If the fault code returns, Go to step 4.
    2. No; Go to step 4.
  4. Check for other fault codes. Are there any air management system fault codes present for the Intake Throttle Valve (ITV), Intake Manifold Pressure (IMP), Intake Air Temperature (IAT), turbocharger, etc.?
    1. Yes; diagnose the other fault codes first.
    2. No; Go to step 5.
  5. Are there any Exhaust Gas Recirculation (EGR) system fault codes present?
    1. Yes; diagnose the other fault codes first.
    2. No; Go to step 6.
  6. Are there any other NOx sensor fault codes present?
    1. Yes; diagnose the other fault codes first.
    2. No; Go to step 7.
  7. Are there any fault codes for the DEF metering unit, DEF pump, or DEF air valve present?
    1. Yes; diagnose the other fault codes first.
    2. No;Go to step 8.
  8. Are there any ACM temperature or pressure fault codes present?
    1. Yes; diagnose the other fault codes first.
    2. No; Go to step 9.
  9. Turn the ignition OFF.
  10. Use DEF test strip A0005850202 to check for diesel fuel or oil contamination of the DEF fluid. Refer to section "Checking Diesel Exhaust Fluid Quality" . Do the test strips or visual inspection indicate that the DEF is contaminated?
    1. Yes; for diesel fuel or oil contamination, refer to 13 TS-17 and refer to appropriate Original Equipment Manufacturer (OEM) literature for DEF tank cleaning/flushing procedures. Refill the DEF tank with new DEF. Verify repair.
    2. No; Go to step 11.
  11. Using a refractometer from the DEF Test Kit W060589001900, measure the DEF percentage. Refer to section "Checking Diesel Exhaust Fluid Quality" . Is DEF percentage between 28% and 36%?
    1. Yes; Go to step 12.
    2. No; flush the DEF system. Refer to section "Flushing of the Diesel Exhaust Fluid System" . Verify repair.
  12. Turn the ignition ON (key ON, engine OFF).
  13. Compare the DEF pressure sensor reading to the barometric pressure sensor reading. Are the readings within 29.6 kPa (4.3 psi) of each other?
    1. Yes; Go to step 14.
    2. No; replace the DEF pressure sensor. Refer to section "Removal of the Diesel Exhaust Fluid Pressure Sensor" . Verify repair.
  14. Perform the DEF quantity service routine. Refer to section "Diesel Exhaust Fluid Quantity Test - EPA10" . Go to step 15.
  15. Monitor the amount of DEF dispensed into the DEF-safe container included in DEF test kit W060589001900. Is the amount of DEF dispensed between 102 and 138 mL (3.7 and 4.5 oz.)?
    1. Yes; Go to step 16.
    2. No; flush the DEF metering unit. Verify repair.
  16. Disconnect the DEF dosing valve electrical connector.
  17. Start the engine.
  18. Run the EPA10 Perform Performance Check - Low Temperature ATD procedure to check the NOx sensors. Refer to section "EPA10 Perform Performance Check - Low Temperature ATD" . Are the Inlet NOx sensor and outlet NOx sensor readings within 50 Parts Per Million (PPM) of each other?
    1. Yes; Go to step 20.
    2. No; replace the outlet NOx sensor. Go to step 19.
  19. Run the EPA10 Perform Performance Check - Low Temperature ATD procedure to validate the NOx sensors are reading correctly. Refer to section "EPA10 Perform Performance Check - Low Temperature ATD" . Are the inlet NOx sensor and outlet NOx sensor readings within 50 Parts Per Million (PPM) of each other?
    1. Yes; Go to step 20.
    2. No; replace the inlet NOx sensor. Go to step 20.
  20. Reconnect the DEF dosing valve electrical connector.
  21. Start the engine and perform a parked regeneration while monitoring the NOx efficiency. Is the NOx efficiency above 70%?
    1. Yes; clear codes and release the vehicle.
    2. No; Go to step 22.
  22. Review the last seven minutes of the parked regeneration log file; was the SCR inlet temperature more than 38°C (68.4°F) lower than SCR outlet temperature?
    1. Yes; Go to step 23.
    2. No; replace the ATD. For a One-box system, replace the DOC/SCR module. For a Two-box system, replace the SCR module. Complete the ATD check list to identify cause of failure.Refer to section "ATD Checklist - EPA07/EPA10/GHG14" .
  23. Perform a low temperature Aftertreatment Device (ATD) check using DiagnosticLink to check for a drifted temperature sensor. Refer to section "EPA10 Perform Performance Check - Low Temperature ATD" . Are the SCR inlet and SCR outlet temperatures within 25°C (45°F) during the last five minutes of this test?
    1. Yes; replace the ATD. For a One-box system, replace the DOC/SCR module. For a Two-box system, replace the SCR module. Complete the ATD check list to identify cause of failure. Refer to section "ATD Checklist - EPA07/EPA10/GHG14" .
    2. No; replace the drifted SCR temperature sensor and verify repair.
Customer: replied 1 year ago.
I think I probably need to take to a shop. Thanks
Expert:  roybelding replied 1 year ago.

if you dont have the software for following the flow chart then yes, it would be best to let soeone look at it that knows the system

Roy

Expert:  roybelding replied 1 year ago.

how are you making out????

please dont forget to rate me as it is the only way I get paid for my efforts

Roy