Industrial Equipment
Connect one-on-one with a mechanic who will answer your question
Expert avatar
Curtis B., Technician
821 satisfied customers
Technican turned service manager on multiple lines of equipment used in industry.
Pearl avatarPearl Wilson, Assistant
Mechanic is Online Now

Have industrial equipment repair questions?

Verified mechanics are online around the clock and ready to answer your question online or by phone. 
Related Industrial Equipment questions
Jlg sizzor lift trouble working good just quit got 2 red
jlg sizzor lift trouble working good just quit got 2 red flashing lights on control board … read more
Jeremy
Jeremy
Technician
Associate Degree
18 satisfied customers
Upper controls on an am55 are purging pilot pressure when
Upper controls on an am55 are purging pilot pressure when deadman is squeezed or not .. until you do a function . which causes a delay on fist movment … read more
Jeremy
Jeremy
Technician
Associate Degree
18 satisfied customers
Yale deasl towmoter will not move forward or back type d
yale deasl towmoter will not move forward or back type d gdp080l gnube083 … read more
Curtis B.
Curtis B.
Technician
Associate Degree
821 satisfied customers
I have a jlg 600a that will not turn to the right from the
i have a jlg 600a that will not turn to the right from the basket. everthing else works. its a 2002. serial number(###) ###-####… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
961 satisfied customers
Wow is this real? I have a doosan g40 429042uhvd62. It's
It's starting fine and running for 10 seconds then shutting off. … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
961 satisfied customers
I am working on a JLG scissor lift 2630ES and the control
i am working on a JLG scissor lift 2630ES and the control box is constantly flashing the red battery light and the yellow light beside it with an exclamation point blinks 2 and then 5 times. … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
961 satisfied customers
We have a diesel generator Kubota model number d722-D2 -
We have a diesel generator Kubota model number d722-D2 - ES01 serial number 75309 7 after you start the generator about a half an hour later the lights start to flicker and then goes back up to normal… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
961 satisfied customers
Hallo. I need an AVR AN-5-203. DCA25-150. I've seen online
I've seen online that Alibaba has a replacement for the AVR I'm looking for.… read more
Curtis B.
Curtis B.
Technician
Associate Degree
821 satisfied customers
Our issue is an error code on a hyster h360hd. the code is
our issue is an error code on a hyster h360hd. the code is 4501 and we can't seem to locate it on our service manual … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
961 satisfied customers
Can not find stamped number on 305g Lincoln welder ., need
can not find stamped number on 305g Lincoln welder ., need it to order carburetor rebuild kit. … read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
225 satisfied customers
I have a 2011 C50SD serial #P455D-0040-9801 and it will only
I have a 2011 Clark C50SD serial #P455D-0040-9801 and it will only go forward. When in neutral it goes forward and when in reverse the unit stops. I'm hoping it could be electrical and not the transmi… read more
Curtis B.
Curtis B.
Technician
Associate Degree
821 satisfied customers
This is a ranger bucket truck. when i operate the boom from
This is a hi ranger bucket truck. when i operate the boom from the lower controls it works fine. However when I operate from the bucket I cannot go left. All other movment is ok from both bucket and l… read more
Jeremy
Jeremy
Technician
Associate Degree
18 satisfied customers
Snorkel lift UNO 41G, SN 972851. Drive started running
Snorkel lift UNO 41G, SN 972851. Drive started running (moving) slowly. Also noticed when pedal was stepped on to engage controls on platform, engine would act like it had a load on it but no controls… read more
Curtis B.
Curtis B.
Technician
Associate Degree
821 satisfied customers
My 2016 Volvo I-shift is jerking while in reverse don't want
My 2016 Volvo I-shift is jerking while in reverse don't want to go while in reverse. Like it's trying to jump out of gear … read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
961 satisfied customers
We have an Eagle Lift 47' manlift. We are having problems
We have an Eagle Lift 47' manlift. We are having problems with the top boom slowly leaking off. It doesn't do it everytime we use it just occasionally. … read more
Jeremy
Jeremy
Technician
Associate Degree
18 satisfied customers
I have a 655 E that stopped moving. I checked the fuse box
I have a 655 E that stopped moving. I checked the fuse box and I have a short. The fuse keeps popping. Im trying to figure out what that fuse feeds so i can trace the short. The hoe just stopped unexp… read more
Wayne
Wayne
Journeyman
Vocational, Technical or Trade Scho
225 satisfied customers
Have s60 genie lift with lrg425efi engine retrofit. fires
Have s60 genie lift with lrg425efi engine retrofit. fires briefly then shuts down with code 537 (throttle unable to open.) Happened before and replaced a burned capicator in ecm 1u1l 12a650 ca. worked… read more
Daniel Wilson
Daniel Wilson
Auto Mechanics 1&2/diesel mech
961 satisfied customers
We have a Demag 5K Powerlift hoist, Model EKP212H11L4/1 with
We have a Demag 5K Powerlift hoist, Model EKP212H11L4/1 with a worn cable drum and a non functioning brake. What could be the brake issue and are replacement parts available for an older model hoist a… read more
Jeremy
Jeremy
Technician
Associate Degree
18 satisfied customers

Convenient answers to your industrial equipment questions


The qualified Experts on JustAnswer regularly respond to industrial equipment questions like:


  • My Genie S-40 will not operate with foot pedals from the basket. Can you help?
  • Can you tell me the meaning of fault code 0100 on my TMZ 5030 T5002-222?
  • I need to change the Chev 3.0 flywheel on my 1985 Hyster S50E, but I can't separate the trans or bellhousing. Does it have to come out as a unit?
  • My T500j code flashes 9 times and the arm won’t raise up. What’s wrong?
  • I have a 3219 skyjack and all it will do is run the hydraulic pump. None of the other functions work. What's my problem?
To give you the best advice, the Expert will need some information. You should be ready to answer questions such as:


  • Are you fixing this yourself?
  • What have you tried so far?
  • What is the complete model and serial number of your machine?

With this information, you'll be ready to have a constructive session with the Expert.