How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask eauto Your Own Question
eauto
eauto, The Car Guy
Category: Hyundai
Satisfied Customers: 16109
Experience:  ase certified, imac, macs, bridhestone certified
6149662
Type Your Hyundai Question Here...
eauto is online now
A new question is answered every 9 seconds

Can you help me, I have a Hyundai Tucson 2005, I have this

Customer Question

Hi Sir Can you help me
JA: What is the model/year of your Hyundai?
Customer: I have a Hyundai Tucson 2005
JA: Are you fixing your Tucson yourself? What have you tried so far?
Customer: I have this code p0885
JA: Just to clarify, what's the exact code? And have you tried to reset it?
Customer: P0885
JA: Anything else you want the mechanic to know before I connect you?
Customer: NO
Submitted: 8 months ago.
Category: Hyundai
Expert:  Jerry replied 8 months ago.

Hello and welcome. My name is ***** ***** you for visiting the site, I am reviewing your question and will reply shortly, thanks.

Customer: replied 8 months ago.
My email is***@******.***
Expert:  Jerry replied 8 months ago.

Thank you but you have to accept the offer.

Customer: replied 8 months ago.
No, I don't want it.
Customer: replied 8 months ago.
I just need a solution for this code P0885,
Hyundai Tucson 2005 v6 2.7l
Expert:  eauto replied 8 months ago.

have you changed the relay?

Customer: replied 8 months ago.
NO
Expert:  eauto replied 8 months ago.

thats the first step

Customer: replied 8 months ago.
I don't change it.
Expert:  eauto replied 8 months ago.

can you?

Expert:  eauto replied 8 months ago.

GENERAL DESCRIPTION
The HIVEC Automatic Transmission supplies the power to the solenoid valves by way of a control relay. When the TCM sets the relay to ON, the relay operates and the battery power is supplied to all the solenoid valves. When the TCM sets the relay to OFF, all solenoid valve power is shut off and the transmission is held in the 3rd gear position. (Fail Safe Mode)

DTC DESCRIPTION
The TCM checks the A/T control relay signal by monitoring the control signal. If, after the ignition key is turned on, an unexpected voltage value, which is quite a bit lower than battery voltage is detected, the TCM sets this code.

Customer: replied 8 months ago.
I am waiting for a response ,help me please.
Expert:  eauto replied 8 months ago.

change the at control relay................... thats the answer

Customer: replied 8 months ago.
Changing the relay is not resolved my problem. Cause l had to change the crankshaft sensor l put a new one. Engine is crancking but do not start.
Customer: replied 8 months ago.
But the scan tool doesn't detect any code. It displays no DTC.
Expert:  eauto replied 8 months ago.

so it does not run? why would you not say that from the start?

Customer: replied 8 months ago.
it does not run.
Expert:  eauto replied 8 months ago.

so why tell me after the fact....you tell half the story and expect the correct answer.... does it have spark ? compression? injector pulse? fuel pressure?

Customer: replied 8 months ago.
Expert:  eauto replied 8 months ago.

so if it has all of the above it will run....

Customer: replied 8 months ago.
But it does not run.
Expert:  eauto replied 8 months ago.

how many psi of fuel pressure? and what is the compression?

Customer: replied 8 months ago.
I will get back to you tomorrow, l don't know all what you ask me.
Expert:  eauto replied 8 months ago.

well you answered yes ...these are the questions i need answers to ...in order to solve your issue...

Customer: replied 8 months ago.
Psi fuel pression and compression are good.
Customer: replied 8 months ago.
After changing the AT Control relay there's still no power in the solenoid.
Expert:  sprinkles08 replied 8 months ago.

Hello and welcome to JustAnswer!

Do you still need help?

Customer: replied 8 months ago.
Expert:  sprinkles08 replied 8 months ago.

Have you checked for spark?
What were the fuel pressure and compression readings?

Customer: replied 8 months ago.
Fuel pressure and compression are good, but l don't have spark
Expert:  sprinkles08 replied 8 months ago.

What fault codes are setting in the engine controller?

Customer: replied 8 months ago.
P0885 the first time l scan it, but after changing the AT control relay l don't have any code.
Expert:  sprinkles08 replied 8 months ago.

If it doesn't have spark there is little chance that no fault codes are setting. Give the starter a solid ten seconds of cranking without letting up and then check for codes again.

Customer: replied 8 months ago.
Ok
Expert:  sprinkles08 replied 8 months ago.

Let me know what you find and we can go from there.

Customer: replied 8 months ago.
Scan tooll still display no DTC.
Expert:  sprinkles08 replied 8 months ago.

It's an actual scan tool?

Customer: replied 8 months ago.
It's an ordinary one, not complicated.
Expert:  sprinkles08 replied 8 months ago.

What is the brand and model of what you're using?

Customer: replied 8 months ago.
I don't see any brand name on it. It's a OBD II tool.
Expert:  sprinkles08 replied 8 months ago.

But is it a generic OBDII code reader or an actual scan tool? A scan tool is a multi thousand dollar tool that will allow for the monitoring of data and perform actuator tests.

Customer: replied 8 months ago.
Expert:  sprinkles08 replied 8 months ago.

Do you have a compression gauge?

Customer: replied 8 months ago.
No
Expert:  sprinkles08 replied 8 months ago.

Have you checked fuses? If fuses are good and you don't see a visual wiring issue you're going to need testing equipment to be able to diagnose the problem.

Customer: replied 8 months ago.
Fuses are good
Customer: replied 8 months ago.
There is any wiring issue
Expert:  sprinkles08 replied 8 months ago.

Unless you'd like to start replacing likely parts you're going to need to need the ability to do testing to proceed.

Customer: replied 8 months ago.
Ok
Expert:  sprinkles08 replied 8 months ago.

Let me know if you need any more help.

Customer: replied 8 months ago.
No problem, l will write you tomorrow.
Expert:  sprinkles08 replied 8 months ago.

Great!

Expert:  eauto replied 8 months ago.
Please remember to only rate my service when you are satisfied. IF you feel the need to rate "Poor Service" or "Bad Service", please stop and reply to me via the REPLY TO EXPERT button with the issue you have. I will be happy to continue further and do everything I can to provide you with the service you seek.
I am not paid unless I get a rating of 3 to 5 Stars/Smiley Faces. As always I'm happy to provide my time/service & resources so If I have helped you with your question, please give me an appropriate rating so that I get credit for helping you. Thank you and good luck with your vehicle!