HVAC

Have HVAC questions? Ask an HVAC Expert for answers

Ask an Expert,
Get an Answer ASAP!

My furnace is having trouble staying on, and reads out with…

Customer Question
My furnace is having...

My furnace is having trouble staying on, and reads out with a couple error codes: E227, which says “Low pressure switch opened during trial for ignition repairs run mode”

Contractor's Assistant: How old is the appliance? Have you gotten error messages before?

I’ve tried to find 24-hour service, but have been having trouble

Contractor's Assistant: Do you plan on doing the work yourself?

Not unless there is something relatively simple to do

Contractor's Assistant: Anything else we should know to help you best?

No, I don’t think so

Submitted: 7 months ago.Category: HVAC
Show More
Show Less
Ask Your Own HVAC Question
Answered in 4 hours by:
12/14/2017
HVAC Technician: airheatman, HVAC Technician replied 7 months ago
airheatman
airheatman, HVAC Technician
Category: HVAC
Satisfied Customers: 9,174
Experience: Furnace, A/C and heat pump specialist.
Verified

About the only thing you can do without test equipment is make sure there is not water standing in the furnace drain hoses.

Ask Your Own HVAC Question
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a hvac technicianLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask airheatman Your Own Question
airheatman
airheatman
airheatman, HVAC Technician
Category: HVAC
Satisfied Customers: 9,174
9,174 Satisfied Customers
Experience: Furnace, A/C and heat pump specialist.

airheatman is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

You did one super job of explaining to me everything there is to know about this fridge. I'm looking forward to asking you questions in the future.

JimmyBagley, IA

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

< Previous | Next >

Meet the Experts:

Phil

Phil

Mechanical Engineer

7,426 satisfied customers

Retired HVAC/ Electrical & Boiler contractor. Industrial

Rick Mather

Rick Mather

HVAC Technician

3,133 satisfied customers

35 years experience, HVAC

Matthew

Matthew

HVAC Technician

2,014 satisfied customers

14 years experience in the HVAC field of service, installation, Manual J & D calculations

Brian HVAC Guy

Brian HVAC Guy

HVAC Technician

1,019 satisfied customers

I have been an HVAC/R mechanic/technician for 30+ years.

Kenton Guidry

Kenton Guidry

HVAC Technician

963 satisfied customers

12 years install/service experience.

Rick Ridley

Rick Ridley

UK Heating Engineer

871 satisfied customers

Retired But have had 30 years on the tools, Ex CORGI

Tom

Tom

HVAC Technician

770 satisfied customers

16+yrs HVAC/R service. Residential Commerical Industrial

< Previous | Next >

Related HVAC Questions
TEMPSTAR m#N9MSE0801716A...inducer motor starts..was
TEMPSTAR m#N9MSE0801716A...inducer motor starts..was lighting ignitor then firing and would immediately go out..replaced sensor and press switches...now ignitor will not glow....cked flue,f/a intake c… read more
Gaztech
Gaztech
Technician
Vocational, Technical or Trade School
1,942 satisfied customers
Furnace model G9T10014UPC13C burner will not ignite. Fan
Coleman furnace model G9T10014UPC13C burner will not ignite. Fan runs in continuous on setting thermostat but not in auto mode. Red light flashing on board. … read more
Gaztech
Gaztech
Technician
Vocational, Technical or Trade School
1,942 satisfied customers
How much does this cost? I have a furnace flashing 34 error
I have a bryant furnace flashing 34 error code-ignition failure, I am an hvac tech myself, not sure what is going on … read more
airheatman
airheatman
HVAC Technician
9,174 satisfied customers
No ac. found the thermostat screen was blank. Tried
no ac. found the thermostat screen was blank. Tried inserting batteries. The screen came on, but still no ac. checked voltge coming into the thermostat. no 24vdc there. went upstairs where the wire go… read more
Brian HVAC Guy
Brian HVAC Guy
HVAC Technician
High School
1,019 satisfied customers
York 90 no heat in auto mode doesn't turn on in on mode fan
Customer: york 90 no heat in auto mode doesn't turn on in on mode fan blows but no ignition … read more
airheatman
airheatman
HVAC Technician
9,174 satisfied customers
I have a EL296UHE - the furnace only comes on a minute at a
I have a EL296UHE - the furnace only comes on for about a minute at a time and then shuts off - it's dropped to 55 degrees in the house… read more
Tim H
Tim H
Lead building engineer
Vocational, Technical or Trade Scho
1,922 satisfied customers
HVAC question My furnace model # is C8MPT075f14A and the
HVAC question My furnace model # ***** ***** and the system blinking continuously. Any idea is it has any problem?… read more
Billy
Billy
Journeyman Service Technician
State Licensed Mechanical Contractor
9,330 satisfied customers
We have an older Bryant I 90 plus. We occasionally need to
We have an older Bryant I 90 plus. We occasionally need to replace the igniter and did that a couple of weeks ago. That resolved the problem for a while. The temperature is again not reaching the set … read more
HVAC Guru
HVAC Guru
Service Technician
Associate Degree
682 satisfied customers
What to do when heat stops on Lennoz and Honeywell furnace
I have a Lennox CX34-25B-6F-1 furnace and Honeywell VR9200 (those are the two model numbers I found. They heat has stopped. When I took the cover, I saw a red blinking light and looked. It recorded th… read more
V12Tech
V12Tech
252 satisfied customers
we have a Carrier 58mya080 furnace serial #0398a003a get codes
we have a Carrier 58mya080 furnace serial #0398a003a get codes 12 and 13. At call for heat, pre blower comes on for 90 seconds, no gas, no ignition, especially on damp days after heat not used for day… read more
Billy
Billy
Journeyman Service Technician
State Licensed Mechanical Contractor
9,330 satisfied customers
My Bryant furnace is not putting out warm air. I just went
My Bryant furnace is not putting out warm air. I just went and looked at the RED LED status light and it was blinking. After removing both panels and then replacing the top panel, the light remained o… read more
Billy
Billy
Journeyman Service Technician
State Licensed Mechanical Contractor
9,330 satisfied customers
I have a carrier model 58PAV135-20 furnace. It wont start
I have a carrier model 58PAV135-20 furnace. It won't start and the LED appears to be flashing a code (2 short flashes followed by 4 long flashes). Is there a place online that describes these codes?… read more
Billy
Billy
Journeyman Service Technician
State Licensed Mechanical Contractor
9,330 satisfied customers
Lennox SLP98UHV furnace pressure switch giving error codes.
I installed a new Lennox SLP98UHV furnace in our home. However, the air temperature in the basement was close to freezing. I should have warmed up the ambient air to between the recommended 16 C and 2… read more
Phil
Phil
Mechanical Engineer
Degree, Mech Engr Technology
7,426 satisfied customers
We have a Vizo Plus 24 Pre-Mix condensing combination boiler.
We have a Vizo Plus 24 Pre-Mix condensing combination boiler. We now have an F4 error flashing. The condensate trap has been checked, so has the gas pressure and everything fine. Any clues?… read more
Rick Ridley
Rick Ridley
UK Heating Engineer
30 years on the tools
871 satisfied customers
I have a York Diamond 90 P3U which for the past ywo weeks would
I have a York Diamond 90 P3U which for the past ywo weeks would cycle to heat, ignite, and then cut out. It would do this many times before actually returning to normal. No error codes at those times.… read more
TimVZ26
TimVZ26
Service Foreman
Vocational, Technical or Trade Scho
157 satisfied customers
I have a Carrier 58PAV111 furnace that tries to fire up but
I have a Carrier 58PAV111 furnace that tries to fire up but then stops and then I smell gas. I think the code it is flashing is 12. I tried shutting off the gas and the power to the furnace and left t… read more
Richard
Richard
District Technical Manager
Vocational, Technical or Trade Scho
1,416 satisfied customers
We have a Carrier Weathermaker 9200. Were currently having
We have a Carrier Weathermaker 9200. We're currently having a blizzard and our air intake valve got clogged. We cleaned it out, but the furnace smelled hot and had water underneath it. We turned it on… read more
Billy
Billy
Journeyman Service Technician
State Licensed Mechanical Contractor
9,330 satisfied customers
Hi there, I have a Carrier Weathermaker 8000. From 1994.
Hi there, I have a Carrier Weathermaker 8000. From 1994. My LED diagnostic light is blinking but I do not have an error code legend on my furnace, so I do not know what the flashes mean. Help!… read more
Billy
Billy
Journeyman Service Technician
State Licensed Mechanical Contractor
9,330 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x