How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Gaztech Your Own Question
Gaztech
Gaztech, HVAC Technician
Category: HVAC
Satisfied Customers: 475
Experience:  Owner at Gaztech
92290868
Type Your HVAC Question Here...
Gaztech is online now
A new question is answered every 9 seconds

My furnace is blowing cold air. The red light is blinking

Customer Question

My furnace is blowing cold air. The red light is blinking 6times
JA: Did you double-check the thermostat's settings? And what about the filters?
Customer: Replaced filter and checked thermostat
JA: Do you plan on doing the work yourself?
Customer: If possible
JA: Anything else we should know to help you best?
Customer: Just what the code of 6 blinks means
Submitted: 9 months ago.
Category: HVAC
Expert:  Gaztech replied 9 months ago.

What is the exact make and model on furnace,

model is usually found inside top compartment on a sticker right or lft side inner panel

Customer: replied 9 months ago.
Model number is ***** fan was running constantly... Thermostat wont shut it off, i replaced thermostat... Same thing..had to shut it down at switch on side of furnace... Still blinking 6 times
Customer: replied 9 months ago.
Blowing cold air.. burner not kicking on
Expert:  Gaztech replied 9 months ago.

Te furnace blower is running constantly because it is in lockout mode,

and..

you have to go and read the error code trough the small window of bottom panel.

count the amount of led flash between pauses

Customer: replied 9 months ago.
6 blinks
Expert:  Gaztech replied 9 months ago.

Count flash code again , 6 is non existant

Expert:  Gaztech replied 9 months ago.

Flame sensor probably needs to be cleaned, it is located within the burners, it looks like this picture

Customer: replied 9 months ago.
Checked flashes 4 times. Each time 6 blinks
Customer: replied 9 months ago.
I will look and see are there two of them
Expert:  Gaztech replied 9 months ago.

Found the error code, says flame rollout switch has sensed flame coming back out

• Check flue and air inlet piping for blockage, proper length, elbows, and termination.

• Check rollout limit switch, the red reset buttom is poped out, press it back in but check for flue blockage.

here is a picture of what it looks like

Expert:  Gaztech replied 9 months ago.

it is around the burners

Expert:  Gaztech replied 9 months ago.

Hello????

Customer: replied 9 months ago.
Cleaning flame sensor then willnput bqck and look for other thing. Is thst in lower panel
Expert:  Gaztech replied 9 months ago.
Expert:  Gaztech replied 9 months ago.

push in red button in the middle of switch shown in pictur, there is up to 3 switches like this around the burners

Customer: replied 9 months ago.
Iservice guy showed up said induction motor notnworking he spun it and got it working.
Customer: replied 9 months ago.
But took alot ofspinning
Expert:  Gaztech replied 9 months ago.

NOTE: I can only get paid for assisting you if you RATE ANSWER the 5 star rating at top of page after you are satisfied with answer.

Happy all is good

Best regards

Luke

Expert:  Gaztech replied 9 months ago.

Thanks

Customer: replied 9 months ago.
Kicked off again now blinking three times ??
Expert:  Gaztech replied 9 months ago.

Hello,,,

Expert:  Gaztech replied 9 months ago.

there is something wrong with your system and it was not detected with your last service call, you need to resolve this with a full service maybe with a second visit, or a different service tech.

Expert:  Gaztech replied 9 months ago.

I see that the question is still open , do you need more help?