GMC

GMC troubleshooting questions? Ask a mechanic for answers

Ask an Expert,
Get an Answer ASAP!

2014 SIERRA IN AN ACCIDENT,WE ARE A COLLISION SHOP. REPLACED…

Customer Question
2014 SIERRA IN AN...

2014 SIERRA IN AN ACCIDENT,WE ARE A COLLISION SHOP.

Mechanic's Assistant: Are you fixing your Sierra yourself? What have you tried so far?

REPLACED THE STEERING ANGLE SENSOR BECAUSE OF CODE C0170.NOW WE HAVE C0170,U0428,C0544

Mechanic's Assistant: Which particular sensor are you asking about? And have any trouble codes been triggered?

REPLACED STEERING ANGLE SENSOR CODES C0170,C0544,U0428

Submitted: 1 month ago.Category: GMC
Show More
Show Less
Ask Your Own GMC Question
Customer reply replied 1 month ago
steering angle sensor has been replaced and put back together and diagnostic scan tool clears codes until the steering wheel is turned all the way to the left and then the codes appear again.They do not appear when we turn wheel to the right.
Answered in 9 minutes by:
3/12/2018
GMC Mechanic: Gary, GM Technician replied 1 month ago
Gary
Gary, GM Technician
Category: GMC
Satisfied Customers: 1,645
Experience: Senior Technician
Verified

Hello! My name is Gary.
Welcome to JustAnswer.
I'm reviewing your question now, and will post back with a reply shortly.

Ask Your Own GMC Question
GMC Mechanic: Gary, GM Technician replied 1 month ago

The SAS needs to be programmed after replacement.

The wheel alignment should be checked and adjusted first.

Gary

Ask Your Own GMC Question
Customer reply replied 1 month ago
can you explain more,we have a scan tool and it clears them and then they reappear when wheel is turned to left
Customer reply replied 1 month ago
no call
Customer reply replied 1 month ago
hello?
Customer reply replied 1 month ago
programmed by a dealer or a shop scan tool?
GMC Mechanic: Gary, GM Technician replied 1 month ago

Generally only a dealer scan tool can do this programming setup.

Do you have a dealer nearby?

Gary

Ask Your Own GMC Question
GMC Mechanic: Gary, GM Technician replied 1 month ago

Do you need any further help?

I hope my advice has been of assistance to you.

Gary

Ask Your Own GMC Question
Was this answer helpful?
Ask Gary Your Own Question
Gary
Gary
Gary, GM Technician
Category: GMC
Satisfied Customers: 1,645
1,645 Satisfied Customers
Experience: Senior Technician

Gary is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Gm Tech (Cam)

Gm Tech (Cam)

GMC Mechanic

1,696 satisfied customers

GM Grand Master Technician 2007. 14 year experience.

Gary

Gary

ASE Certified Technician

1,557 satisfied customers

GCM master tech over 25 years

Dave Nova

Dave Nova

GMC Technician

929 satisfied customers

ASE Master Certification. GM World Class Certification

Chris (aka-Moose)

Chris (aka-Moose)

GMC Technician

583 satisfied customers

16 years of experience

Ron Z.

Ron Z.

- GMC Tech -

259 satisfied customers

18+yrs experience. State Inspector & GMC Diagnostics/Repair

George H.

George H.

ASE MasterTechnician

227 satisfied customers

15+ Years ASE Master Technician with Level 1 Certification

Don - Mo Lurch

Don - Mo Lurch

ASE Certified Technician

218 satisfied customers

GM, GMC, Chevrolet Cert., Heavy Line Mech, Race Shop Owner, Mobile Electronics

< Previous | Next >

Related GMC Questions
Are you really there. Are you a real person? I put thw wrong
i put the wrong oil filter on my car i think the threds are wrong … read more
David Craig
David Craig
OWNER/MECHANIC
Associates
5,064 satisfied customers
I have a 2010 and the temp gauge stopped working and the
I have a 2010 and the temp gauge stopped working and the dash is saying engine hot A/C off … read more
Ron Z.
Ron Z.
- GMC Tech -
Vocational, Technical or Trade Scho
259 satisfied customers
I have tried the fuse ECM1 nd it works I just still no power
I have tried the fuse ECM1 nd it works I just still no power from the pump when cranking nd nothing from the injectors inmy 94 gmc g2500 vandura… read more
tim37857
tim37857
Mechanic
High School or GED
71 satisfied customers
I would like to know why rubber housing on vacuum actuator
hello,I would like to know why rubber housing on vacuum actuator keeps tearing , 2003 gmc Sonoma 4.3 automatic trans. thank you … read more
camerontech
camerontech
20 year experience diagnostic technician
class a
638 satisfied customers
I have taken my 2004 Yukon to a local shop. Big mistake.
I have taken my 2004 Yukon to a local shop. Big mistake. They worked on heat system (Directional doors) and say it works good. I strongly disagree. They also were to replace the Audio (Bose radio/6 CD… read more
roy
roy
Associate Degree
3 satisfied customers
I recently replaced the starter in my 89 gmc 1500. It would
i recently replaced the starter in my 89 gmc 1500. It would spin the flywheel and sometimes start. If it didnt start on first or secone try it would not spin flywheel any more. Had battery tested and … read more
eric remington
eric remington
FORMER SHOP OWNER/TECHNICIAN/INSPECTOR
associates degree
480 satisfied customers
2011 GMC 3500HD 6.6 LML DURAMAX (Stock, no mods). Code P0420
2011 GMC 3500HD 6.6 LML DURAMAX (Stock, no mods).Code P0420 - Catalyst System Efficiency below Threshold Bank 1. Code P2463 - Particulate Filter restriction - soot accumulation. Upon starting DIC Msg … read more
Eric
Eric
Retired
N/A
14,436 satisfied customers
2001 yukon Denali 6.0. Power steering shaft pulley shaft
2001 yukon Denali 6.0. Power steering shaft pulley shaft broke. Replaced pump, still no power steering. Put a second pump on, still no power steering. Fluid doesn't move in reservoir. What's my next s… read more
Dan
Dan
Automotive Technician
Vocational, Technical or Trade Scho
25 satisfied customers
I HAVE 2004 SILVERADO 2500HD WITH 6.0L GAS WHEN I TURN MY
HELLO I HAVE 2004 SILVERADO 2500HD WITH 6.0L GAS WHEN I TURN MY KEY TO THE ON POSITION THE ONLY LIGHT I GET IN THE CLUSTER IS THE ENGINE LIGHT MY SECURITY LIGHT NEVER TURNS ON OR AIR BAG ABS NOTHING A… read more
Gm Tech (Cam)
Gm Tech (Cam)
GMC Mechanic
Vocational, Technical or Trade Scho
1,696 satisfied customers
I have a 2009 GMC 2500 HD 6.6 turbo would only run for about
I have a 2009 GMC 2500 HD 6.6 turbo would only run for about 4 sec. I replaced the filter,housing and water sensor after priming it started and then run for about 20 sec. then died. Any suggestions? T… read more
Gm Tech (Cam)
Gm Tech (Cam)
GMC Mechanic
Vocational, Technical or Trade Scho
1,696 satisfied customers
GMC wont start Relay is working. 170000. 97 jimmy. I am
have not checked out fuel pump yet . I hear somethimg when I turn the key but not sure if it is the pump… read more
Mechanic01
Mechanic01
2,385 satisfied customers
My 07 camry has no power and won't start. good battery,
my 07 camry has no power and won't start. good battery, cleaned grounds in the vicinity where you would find the battery. replaced ignition switch. good starter. there is power to door locks but not t… read more
Dan
Dan
Dealership Technician
Associate Degree
2,009 satisfied customers
The RPM gauge works occasionally. I notice when it's not
The RPM gauge works occasionally. I notice when it's not working so is the air con and engine runs rough. … read more
Gm Tech (Cam)
Gm Tech (Cam)
GMC Mechanic
Vocational, Technical or Trade Scho
1,696 satisfied customers
All my power windows work except right front, replaced
All my power windows work except right front, replaced switch still no go … read more
Don - Mo Lurch
Don - Mo Lurch
ASE Certified Technician
Vocational, Technical or Trade Scho
218 satisfied customers
I have a 5.7 g2500 vandura I have added a new pump new carb
hello I have a 5.7 g2500 vandura I have added a new pump new carb I have checked the fuse ok I put in a new pump relay new oil sensor I have tried hot wiring the pump it comes on so it does work I don… read more
Gary
Gary
ASE Certified Technician
Vocational, Technical or Trade Scho
1,557 satisfied customers
I hava 94 gmc g2500 vandura my fuel pump is nd so is my carb
I hava 94 gmc g2500 vandura my fuel pump is nd so is my carb but is not pumping nor does my carbs injectors I have changed the pump fuse nd the pump rely plus the oil sensor… read more
tim37857
tim37857
Mechanic
High School or GED
71 satisfied customers
My 2010 GMC is pulling the codes P0872, P0877, and P0989.
Hi, my 2010 GMC is pulling the codes P0872, P0877, and P0989. … read more
Gm Tech (Cam)
Gm Tech (Cam)
GMC Mechanic
Vocational, Technical or Trade Scho
1,696 satisfied customers
I have got a hummer h2 with a supercharger n I recently
Second opinion] hi I have got a hummer h2 with a supercharger n I recently drove it and it is not selecting the gear when put into drive (D) but when I try to select any other gears they do get select… read more
Todd Audette
Todd Audette
Automotive Technician
Vocational, Technical or Trade School
357 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x