GMC

GMC Troubleshooting Questions? Ask a Mechanic for Answers

Ask an Expert,
Get an Answer ASAP!

GMC

GMC Sonoma Pickup: How do you remove the hydraulic clutch line

Customer Question
How do you remove the...
How do you remove the hydraulic clutch line for the reservoir on a 2001 gmc sonoma 2.2L engine
Submitted: 2 years ago.Category: GMC
Show More
Show Less
Ask Your Own GMC Question
Answered in 11 minutes by:
5/1/2015
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
Gary
Gary, ASE Certified Technician
Category: GMC
Satisfied Customers: 17,262
Experience: GCM master tech over 25 years
Verified
do you mean the line from the clutch master to the slave cylinder ? or the line into the bottom of the clutch master cylinder ?
Ask Your Own GMC Question
Customer reply replied 2 years ago
The line from the reservoir bottom I Can get the line out from the tranny.but the line to the reservoir is tough to get to
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
there is a small roll pin holding the line into the bottom of the clutch master cylinderusually tapping it out with a roll pin punch will remove it but there is not much room to do so in the truckthe best bet is to remove the clutch master with the line still connected then on a bench or in a vise tap out the pin to release the line out of the bottom of the clutch master cylinder
Ask Your Own GMC Question
Customer reply replied 2 years ago
How do you remove the clutch master cylinder
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
Remove the master cylinder rod from the clutch pedal.Turn the master cylinder 45 degrees counterclockwise to unlock the master cylinder.Disconnect the wiring harness from the clutch master cylinder start switch.Remove the clips securing the clutch line to the dash panel and heat shield.Remove the clutch master cylinder from the dash panel
Ask Your Own GMC Question
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
dont forget to rate us here at Justanswer !
Ask Your Own GMC Question
Customer reply replied 2 years ago
Thank you take care
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
anytimelet me know how it goes
Ask Your Own GMC Question
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
anytimelet me know how it goes
Ask Your Own GMC Question
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
anytimelet me know how it goes
Ask Your Own GMC Question
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
anytimelet me know how it goes
Ask Your Own GMC Question
GMC Mechanic: Gary, ASE Certified Technician replied 2 years ago
dont forget to rate us here at Justanswer !
Ask Your Own GMC Question
Ask Gary Your Own Question
Gary
Gary
Gary, ASE Certified Technician
Category: GMC
Satisfied Customers: 17,262
17,262 Satisfied Customers
Experience: GCM master tech over 25 years

Gary is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Gm Tech (Cam)

Gm Tech (Cam)

GMC Mechanic

1,696 satisfied customers

GM Grand Master Technician 2007. 14 year experience.

Gary

Gary

ASE Certified Technician

17,262 satisfied customers

GCM master tech over 25 years

Dave Nova

Dave Nova

GMC Technician

929 satisfied customers

ASE Master Certification. GM World Class Certification

Chris (aka-Moose)

Chris (aka-Moose)

GMC Technician

563 satisfied customers

16 years of experience

Ron Z.

Ron Z.

- GMC Tech -

255 satisfied customers

18+yrs experience. State Inspector & GMC Diagnostics/Repair

George H.

George H.

ASE MasterTechnician

225 satisfied customers

15+ Years ASE Master Technician with Level 1 Certification

Don - Mo Lurch

Don - Mo Lurch

ASE Certified Technician

216 satisfied customers

GM, GMC, Chevrolet Cert., Heavy Line Mech, Race Shop Owner, Mobile Electronics

< Previous | Next >

Related GMC Questions
06 envoy cranks but no start engine light is on and stays on
06 envoy cranks but no start engine light is on and stays on solid no security lights and fuel pump is on when key is turned to start cranclk speed … read more
AMEDEE
AMEDEE
AUTOMOTIVE TECHNICIAN
Vocational, Technical or Trade Scho
9,105 satisfied customers
06 envoy cranck no start no security light engine light
06 envoy cranck no start no security light engine light stays on solid ran great started right up this am but after it started as I was pulling my arm back to release key my sleeve got caught on key a… read more
Gunvir Singh
Gunvir Singh
1,702 satisfied customers
I have a 2006 gmc sierra with 5.3 engine is it normal for
I have a 2006 gmc sierra with 5.3 engine is it normal for the coolant fans to kick on when temp is over 210 with a.c. off … read more
Eric
Eric
Retired
N/A
14,436 satisfied customers
I have a 2007 GMC acadia the check engine light came on i
I have a 2007 GMC acadia the check engine light came on i scanned it and it gave me the codes p0016 p0017 i changed the crank shaft sensor 1 were is the second one located i cant find it… read more
Dan
Dan
Automotive Technician
Vocational, Technical or Trade Scho
25 satisfied customers
My check engine light flashing car losing speed. It stayed
it stayed on at first replaced water pump an heater hoses. … read more
baddad1
baddad1
technician
High School or GED
5 satisfied customers
2010 gmc Arcadia engine codes p2090 p0008 p0301 p2090 p0010
2010 gmc Arcadia engine codes p2090 p0008 p0301 p2090 p0010 p2088 p2094 p0443 p0445 they also said there might be a wiring that is shorting out . What is the issue? … read more
Gary
Gary
ASE Certified Technician
17,262 satisfied customers
Truck will not remote start and check engine light on.
Truck will not remote start and check engine light on. Advance Diagoned: Getting code P0674 GP cyl 4 issue, U0101 TCCM no comm, and code C0550 … read more
Pete
Pete
Independent Auto Technician
Vocational, Technical or Trade Scho
138 satisfied customers
Engine turns over but wont start. Trouble codes as follows
ok trouble codes as follows PO 301, PO 69E , PO 25A , PO 606...WHERE DO I START? … read more
Chad Farhat
Chad Farhat
Owner
Associate Degree
4,000 satisfied customers
My stepvan utilimaster gas engine Gmc Workhorse is cranking
My stepvan utilimaster gas engine Gmc Workhorse is cranking but not starting. Seems like the ECM isn't getting power. … read more
roy
roy
Associate Degree
3 satisfied customers
I'm having engine surging problems too. ~160k, Automatic.
I've cleaned and reassembled the Mass Air flow sensor, made sure there were not leaks in the pipe … read more
ricardo hohl
ricardo hohl
automotive instructor
Associate Degree
1,818 satisfied customers
With the engine running an turn the headlight switch on the
with the engine running an turn the headlight switch on the engine goes into reduced power mode. If you pull the dimmer the engine dies. … read more
roy
roy
Associate Degree
3 satisfied customers
Creplacet the engine and the instrument cluster does not
creplacet the engine and the instrument cluster does not operate at all now … read more
AMEDEE
AMEDEE
AUTOMOTIVE TECHNICIAN
Vocational, Technical or Trade Scho
9,105 satisfied customers
Traction control light on reduced engine power, No i was
No i was just driving home and power reduced and engine and traction control light came on just happened ten minutes ago no stores open … read more
eauto
eauto
self employed
High School or GED
74 satisfied customers
On the 2012 gmc sierra 1500 the engine harness ends with the
on the 2012 gmc sierra 1500 the engine harness ends with the ecm/pcm, fuse block, throttle control module transmission module what are other two connection ends for… read more
Marvin the Mechanic
Marvin the Mechanic
82 satisfied customers
Engine suddenly stopped when driving and will not even turn
Engine suddenly stopped when driving and will not even turn over … read more
Jerry Newton
Jerry Newton
Vocational, Technical or Trade Scho
2,066 satisfied customers
Check engine light is on, onstar tells me it is an air
check engine light is on, onstar tells me it is an air filter, yet engine is now sluggish and wont stay on … read more
baddad1
baddad1
technician
High School or GED
5 satisfied customers
Aveo 2009: replaced engine. Engine starts but shuts off with
Aveo 2009: replaced engine. Engine starts but shuts off with in 2 or 3 seconds. Any suggestions … read more
Jerry Newton
Jerry Newton
Vocational, Technical or Trade Scho
2,066 satisfied customers
The reduced engine power symbol is on but with no arrow.
The reduced engine power symbol is on but with no arrow. Have not experienced any change in engine performance since I noticed it today. What does this usually indicate? … read more
Dan
Dan
Automotive Technician
Vocational, Technical or Trade Scho
25 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x