How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Mark Your Own Question
Mark, ASE Certified Technician
Category: GM
Satisfied Customers: 847
Experience:  34+ yrs Dealership Exp. - Fully State & ASE Certified - GM Master & GM World Class Tech
Type Your GM Question Here...
Mark is online now
A new question is answered every 9 seconds

2005 GMC Yukon the service ride control lights are on What can I do

Customer Question

I have a 2005 GMC Yukon the service ride control lights are on What can I do
Submitted: 6 years ago.
Category: GM
Expert:  Mark replied 6 years ago.
Greetings and welcome to Just Answer. My name is Mark.

Below is a description of your electronic suspension. It has it's own computer module which stores trouble codes to lead you to diagnostics for repair. If you can access a scanner that is capable of reading "chassis" trouble codes, I can help you with diagnostics AND repair.

Auto-Zone will read codes for free.

Electronic Suspension Control Description and Operation

The electronic suspension control (ESC) system is bi-state real time damping system. The ESC module controls the suspension damper solenoids and suspension position sensors, along with parts of the automatic level control (ALC) system, if 1500 series.


The ESC system consists of the following:

The ESC module
The compressor/leveling module, if 1500 series
- The air pressure sensor, if 1500 series
- The exhaust solenoid, if 1500 series
The compressor motor relay, if 1500 series
The steering handwheel speed/position sensor
The suspension damper solenoids
The suspension position sensors

Electronic Suspension Control (ESC) Module

The objective of the ESC module is to provide ride and handling results that are superior to a passive damper system, both on and off road at all load conditions. The ESC module monitors body-to-wheel height, vehicle speed, handwheel position/speed, lift/dive status and a driver tow/haul input switch status in real time and instantly selects a "normal" or "firm" mode. This is done for each of the front and rear shock absorbers in order to adjust the vehicle for specific road and driving conditions.


The ESC module will also use the rear body-to-wheel displacements and vehicle speed inputs to keep the rear trim height of the vehicle at its desired level. The ESC module will stay awake for approximately ten minutes after ignition off on 1500 series equipped with Automatic Level Control.


Ignition cycle counting is used by the ESC module to detect faults in the system. The objective is to eliminate false/intermittent codes while maintaining an acceptable level of system performance. The operation of the ignition cycle counting requires that a fault condition be present for four consecutive ignition cycles before it will set the fault code and display the "SERVICE RIDE CONTROL" message.


If a fault code is present (without a fault being current), the system will go into one or more degraded modes without displaying a message. Resetting the ignition cycle counter is done by clearing codes with a scan tool. Clearing codes will override ignition cycle counting for one ignition cycle. Therefore, a fault condition will set the fault code immediately if it occurs on the first ignition cycle after the codes are cleared.

Position Sensors

The ESC module provides a common regulated voltage of approximately 5 volts to all 4 of the body-to-wheel suspension position sensors and to the air pressure sensor. The ESC module receives vehicle speed sensor (VSS) discrete output from the PCM. The suspension position sensors provide an analog signal voltage between 0.5 and 4.5 volts to the ESC module. This signal voltage represents the wheel's position relative to the body. The ESC module provides a 5 volt reference and a low reference to the suspension position sensors.

Shock Absorbers

The damper consists of an in-piston two position solenoid with a 1.5-3.3 ohm coil. The response time of the damper is less than 40 ms. The damper is using movement of oil through an orifice for the damping effect.

The suspension damper solenoid is driven ON and OFF by the ESC module. To activate the solenoid, it is initially subjected to full battery voltage for a short period of time. Once the solenoid is pulled-in, the supply voltage is pulse width modulated (PWM). The amount the suspension damper solenoid is activated is based on inputs from the driver Tow/Haul switch, road inputs, position sensor inputs and the powertrain control module (PCM). The ESC module provides a common ground for all 4 of the suspension damper solenoids.

Vehicle Speed

The ESC module receives a vehicle speed input. It is obtained over the CLASS 2 serial communication buss. Vehicle speed is used to determine the amount of damper control necessary.

Warning Message

The SERVICE RIDE CONTROL message is displayed in the IPC message center, depending on the fault that has been encountered. The warning message will be continued to be displayed, until the fault has been corrected.

Customer: replied 6 years ago.
getting the code check today will get back to you
Expert:  Mark replied 6 years ago.
Okay great.

I will be more than happy to see what we can figure out.

Thanks !
Mark and 4 other GM Specialists are ready to help you
Customer: replied 6 years ago.
the code is for a yoke rake sensor is this something I can doo myself
Expert:  Mark replied 6 years ago.
I am sorry but there is no such thing as a "Yoke Rake Sensor".

I have typed in everything I can think of and the search results through GM come up empty. I typed in different spellings and tried to narrow the search with different words. Nothing is coming up.

It would really help if I had a trouble-code number.

When you had your trouble-codes read, did you get a number or did they just give you a description of the failure?