Ford

Have Ford questions? Ask a mechanic for answers ASAP

Ask an Expert,
Get an Answer ASAP!

I have a Ford 2004 F350 6.0 diesel, It is currently is crank…

Customer Question
I have a Ford 2004...
I have a Ford 2004 F350 6.0 diesel,
It is currently is crank no start.
Based on my scan gauge 2: I have the following.
Good oil pressure (900-1200 psi)
Good FICM voltage 48.5 volts
IPR 45% while cranking
But I have no FICM sync.
I also have an edge gauge:
I am getting code P2617 Crank Position signal (output circ/open)
I am getting code P0603 Internal Ctl Mod Kam error
I am getting code P2614 Camshaft Pos signal (output circ/open)
Can you help?
Submitted: 10 months ago.Category: Ford
Show More
Show Less
Ask Your Own Ford Question
Answered in 15 minutes by:
9/28/2017
Ford Mechanic: Pete, Auto Service Technician replied 10 months ago
Pete
Pete, Auto Service Technician
Category: Ford
Satisfied Customers: 33,346
Experience: Over 17 years diagnosing and repairing automobiles various makes and models with some training and certifications.
Verified

Hi my name is ***** ***** I will be happy to assist with this today.In some cases I may need more info to assist better.I apologize for any delay.

With the fault you have here as well as the codes set this will be either wiring at fault leading to or at the PCM needing repaired or replaced or an issue with the PCM itself internally.I would check the wiring at and leading to the PCM for any issues.Any issues found will need repaired.If this is checked and found o.k. I suspect it will need replaced and programmed.Here is the diagnosis for the P2617 code:

https://www.dropbox.com/s/zb9dgqmntr5itgs/c-09-28.gif?dl=0

https://www.dropbox.com/s/hj9vs13rmp55p1w/cr-09-28.gif?dl=0

Here is the info/diagnosis for the P0603 code

https://www.dropbox.com/s/mi1es73x01x7rj2/pc-09-28.gif?dl=0

These 2 diagnosis procedures above will help to pinpoint the wiring or pcm at fault.

If more help is needed, use the reply tab to continue our conversation. If no further assistance is needed, kindly rate my service,your 5 star rating is appreciated ( should be a link to click on here or above).You can rate at any time and we can continue to work on your question as this will not close out your question.Keep in mind in some cases it can be difficult to fully diagnose or help repair your vehicle without seeing it and I work on delivering the best possible answer from what I see to work with.

Thanks Pete

Ask Your Own Ford Question
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a ford mechanicLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask Pete Your Own Question
Pete
Pete
Pete, Auto Service Technician
Category: Ford
Satisfied Customers: 33,346
33,346 Satisfied Customers
Experience: Over 17 years diagnosing and repairing automobiles various makes and models with some training and certifications.

Pete is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

AlvinC answered a question about my Ford truck that only someone with an in-depth knowledge of his subject would have known what was going on.

Rich DUSA

Because of your expertise, you armed me with enough ammunition to win the battle with the dealer. They are installing a fuel filter and fuel pump at no charge to me.

MollyUSA

I needed help with my car on Saturday morning....got a response in 5 minutes, and it was the perfect solution. Thanks again to your service.

Jason V.Kirkland, WA

I do know, after going though this with JustAnswer, that I can somewhat trust my mechanic but I will always contact you prior to going there.

BRNew Jersey

I would (and have) recommend your site to others I was quite satisfied with the quality of the information received, the professional with whom I interacted, and the quick response time. Thanks, and be sure that I'll be back whenever I need a question answered in a hurry.

Stephanie PElm City, NC

used your service this weekend with "Trecers" help. thank you ,thank you, thank you. replaced an A/C fan motor. Local Auto Zone had part. $15.00 "tracer" fee and $40.00 for parts, I saved several hundreds of dollers at a shop. i will recommend you and use you in the future.

David L.Richmond, TX

9 dollars, 2 hours of my time, and I drove away. Your diagnosis was right on the mark. Thank you so much.

PhilMarysville, CA

< Previous | Next >

Meet the Experts:

Ron

Ron

ASE Certified Technician

25,182 satisfied customers

23 years with Ford specializing in drivability and electrical and AC. Ford certs and ASE Certs

Chris (aka- Moose)

Chris (aka- Moose)

Technician

29,223 satisfied customers

16 years experience

John Mc

John Mc

Ford Technician

5,495 satisfied customers

19 years Ford Lincoln Mercury experience

Chuck

Chuck

ASE Certified Technician

1,685 satisfied customers

33 Years Experience,Ford Senior Master,ASE Master,L1 Advanced Engine Performance

Cam

Cam

Journeyman Automotive Technician

10 satisfied customers

GM Grand Master Technician 2007. 14 years Automotive experience.

Mike V.

Mike V.

Auto Service Technician

1,591 satisfied customers

25 years experience on all makes and models, Licensed NYS Inspector.

Richard

Richard

ASE Certified Technician

1,524 satisfied customers

12 years at a Ford Lincoln/Mercury and Jaguar dealer as a technician and shop foreman.

< Previous | Next >

Related Ford Questions
Crank no start. I'm not getting FICM Sync on my torque pro
Hello. Crank no start. I'm not getting FICM Sync on my torque pro scan app. … read more
eric remington
eric remington
FORMER SHOP OWNER/TECHNICIAN/INSPECTOR
associates degree
1,026 satisfied customers
ford f250: 04 ford f250 6.0 died and wont start. had several
04 ford f250 6.0 died and wont start. had several codes including low icp pressure, crank sensor circuit range/performance, internal control module kam malfunction, injector circuit low cyl. 8.… read more
James
James
Bachelors degree automotive technology with minor in diesel
3,578 satisfied customers
F-250: 06 f250 6.0 crank no start ficm 48.5 syc 1 ipr 50% icp
06 f250 6.0 crank no start ficm 48.5 syc 1 ipr 50% icp 1538 during crank. No codes. All fluid levels good. No air bubbles in fuel filter base during crank.… read more
James
James
Bachelors degree automotive technology with minor in diesel
3,578 satisfied customers
I have a 05 ford 6.0 the truck will not start has new hpop
I have a 05 ford 6.0 the truck will not start has new hpop and fitting ipr and icp ficm test out 47 but not start saying ficm is sync but say cmp and ck pos sensor isnt int sync… read more
John Crouch
John Crouch
lead senior master tech
Vocational, Technical or Trade Scho
1,383 satisfied customers
f350 6.0: ok 2003 ford f350 6.0 still wont start checked icp
ok 2003 ford f350 6.0 still wont start checked icp fuel pressure changed starter batteries fuel filters oil filters checked voltages egr valve ac compressor all the other pulleys im out of ideas… read more
Diesel Doc
Diesel Doc
Diesel Technician/Shop Foreman
High School or GED
2,495 satisfied customers
Ford F350 Super Duty: Vehicle was towed in for no start. Died
Vehicle was towed in for no start. Died while driving. No cam signal on first revolution, get less than .5 AC voltage then flat lines. New cam sensor OHMs out at 800. Crank sensor signal and scope pat… read more
TIM MOHR
TIM MOHR
SHOP OWNER
Master's Degree
8,037 satisfied customers
f250: 6.0 diesel..ordinary injector change, cylinder 7. It sat..dtc
I am working on a 06 f250, 6.0 diesel. It was brought in with what thought was going to be an ordinary injector change, cylinder 7. It sat for 1 day and when I went to pull it in shop it would not sta… read more
Thomas
Thomas
Mechanic
High School or GED
1,053 satisfied customers
2006 f350: powerstroke diesel..cam sensor, and crank sensor
2006 f350 powerstroke diesel 6.0 throwing p2617,p2614,p0263 already changed cam sensor, and crank sensor still no start, can you help… read more
Saemery1
Saemery1
Ford Senior Master Dealership Technician
Associate Degree
1 satisfied customers
2003f350: nostartchangedfuelfilters, verified Lop,48voltsat ficm
2003 f350 6.0 no start changed fuel filters, verified Lop, 48volts at ficm still no start.… read more
david
david
Heavy Duty Repair Mechanic
Vocational, Technical or Trade Scho
495 satisfied customers
2007 Ford F-250: diesel engine..It is very hard to start when cold
I have a 2007 Ford F-250 Super Duty with the 6.0 diesel engine. It is very hard to start when cold. You have to crank and crank. Once started and warmed up it runs along fine at around 2000 rpms, but … read more
Diesel Doc
Diesel Doc
Diesel Technician/Shop Foreman
High School or GED
2,495 satisfied customers
f-250: with 48,000 miles..only dtc code..Circuit..crank
Hello, I have a 05 f-250 6.0 diesel with 48,000 miles. I am having a no-start issue. The only dtc code is a P2614 Camshaft Position Output Circuit/Open.The truck will crank and run off either. It soun… read more
Dieseljunky2
Dieseljunky2
Locomotive Mechanic
Ford Certified Technician
310 satisfied customers
Ford f-350: 2004 6.0 diesel and one morning i..restart
i have ford f-350 ,2004 6.0 diesel and one morning i started the truck and it ran for 5 minutes then died out . haven't been able to restart it . it cranks ok but it won't start. i replaced the front … read more
John Crouch
John Crouch
lead senior master tech
Vocational, Technical or Trade Scho
1,383 satisfied customers
2005 F350: a 6.0 and it will stall at idle..idles fine..high idle
I have a 2005 F350 with a 6.0 and it will stall at idle. It idles fine cold on high idle as soon as it comes off of high idle it will stall. sometimes even warmed up it will stay idling untill I step … read more
POWERSTROKE
POWERSTROKE
DIESEL MASTER TECH
Associate Degree
1,040 satisfied customers
2003 ford excursion: 140,000 miles..cranking..voltage..injectors
2003 ford excursion 6.0 diesel 140,000 miles, lost power over time, went dead and restarted after long cranking periods twice. After third time of dying..never started again. No trouble codes, did the… read more
RJ
RJ
Ford Tech
High School or GED
1,573 satisfied customers
2003 f350: cranks..wont start..wouldnt start..drained fuel filter
2003 f350 6.0 ltr diesel cranks but won't start. changed batteries, started and seemed to run fine.turned it off to hookup trailer and it wouldn't start again. drained fuel filter on frame… read more
fordman312009
fordman312009
Associate Degree
404 satisfied customers
super: awhile..charger..crankshaft position output cicuit open
my vehical starts first thing each morning, but if i drive for awhile and shut off it dose not start rightup. it takes at least half an hour to an hour before starting (after cooling down). I got a sc… read more
mcc1228
mcc1228
Licensed Automotive Technician
Vocational, Technical or Trade Scho
44 satisfied customers
2005 F-350: cam position circuit open..truck wont start replaced
Yesterday my 2005 F-350 6.0 threw a code for the cam position circuit open and the truck won't start replaced sensor and truck still won't start please help.… read more
Diesel Doc
Diesel Doc
Diesel Technician/Shop Foreman
High School or GED
2,495 satisfied customers
f 250: it wont start at all, it runs good..cam and crank senser codes
04 6.0 f 250 starts and runs for two seconds most of the time sometimes it wont start at all, it runs good when it does start, fuel psi is 50-60, inj psi is 1300, it had a cam and crank senser codes w… read more
Dennis
Dennis
Senior Master A Technician/Shop Foreman
Vocational, Technical or Trade Scho
758 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x