Chrysler

Chrysler repair questions? Ask a mechanic for answers ASAP

Ask an Expert,
Get an Answer ASAP!

Chrysler Sebring Limited: put new timing set in 2004 2.7 idles…

Customer Question
put new timing set in...
put new timing set in 2004 2.7 idles fine but get close to 2000 rpm it falls on its face cam sensor and crank sensor codes come up replaced both
Submitted: 3 years ago.Category: Chrysler
Show More
Show Less
Ask Your Own Chrysler Question
Customer reply replied 3 years ago
12TH DIGIT IN VIN IS 2 SO IT SAYS TO USE DBEC TARGET WHEEL
Answered in 46 minutes by:
6/25/2015
Chrysler Mechanic: Chad, Lead Master Tech replied 3 years ago
Chad
Chad, Lead Master Tech
Category: Chrysler
Satisfied Customers: 1,114
Experience: Electrical master,Diesel Specialist,Lead tech/ shop foreman
Verified
Where Did you get the cam and crank scensors from?
Ask Your Own Chrysler Question
Customer reply replied 3 years ago
OREILLYS
Chrysler Mechanic: Chad, Lead Master Tech replied 3 years ago
When you put the timing set on, did you rotate the engine by hand two full revolutions to verify the chain was correct?If so, you need to get new sensors from a dealer. The aftermarket sensors never work correctly.
Ask Your Own Chrysler Question
Customer reply replied 3 years ago
yes I did and when I pulled codes it said cam and crank sensors weren't in correlation with each other or something to that effect
Customer reply replied 3 years ago
the crank turned while I was pulling the crank gear off but realigned the marks
Chrysler Mechanic: Chad, Lead Master Tech replied 3 years ago
That code usually means that the timing is off.Something went wrong while you was putting it back together.Either one of the chains for the cams are off, or the main chain is off.But one of the chains is definitely off.
Ask Your Own Chrysler Question
Was this answer helpful?

How JustAnswer works

step-image
Describe your issueThe assistant will guide you
step-image
Chat 1:1 with a chrysler mechanicLicensed Experts are available 24/7
step-image
100% satisfaction guaranteeGet all the answers you need
Ask Don - Mo Lurch Your Own Question
Don - Mo Lurch
Don - Mo Lurch
Don - Mo Lurch, Aftermarket & Factory Electronics
Category: Chrysler
Satisfied Customers: 542
542 Satisfied Customers
Experience: Cert. Chrysler Warnty, Heavy Line Mech, Mobile Electronics. Sales, Installation & Repair for 30 years

Don - Mo Lurch is online now

A new question is answered every 9 seconds

How JustAnswer works:

  • Ask an ExpertExperts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional AnswerVia email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction GuaranteeRate the answer you receive.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

I was skeptical at first but thought I'd give it a try. I was pleasantly surprised. Your site actually is a quality service that I would recommend to others in a heartbeat.

StanSayre, PA

I AM VERY GLAD THAT I TOOK A CHANCE ON YOUR PROBLEM SOLVING SKILLS. I WAS SUCCESSFUL IN REPLACING THE FUEL PUMP. MY TRUCK RUNS LIKE A CLOCK. IT RUNS LIKE THE DAY I BOUGHT IT. NO LUNGING FORWARD, THE TURBO REACTS THE SECOND I STOMP ON THE GAS, AND IT HAS A LOT MORE POWER AND EVEN SOUNDS BETTER TO ME. IT SAVED ABOUT $500.00 BY DOING THE WORK MYSELF. I GIVE YOU ALL THE CREDIT FOR YOUR DIAGNOSING THE PROBLEM, JUST FROM THE SYMPTONS I GAVE YOU OVER THE e MAIL. I WILL USE YOUR WEB SITE AGAIN AND REFER MY FRIENDS. THANKS SO MUCH FOR THE HELP.

TOM WHITTAKERUSA

Just a quick line to tell you how pleased I am to have my brakes working properly after all this time. Your answer was what I needed. I would certainly recommend you highly. God bless!

Rev. Jerry BaysingerHolts Summit, Mo

I recently asked a question about my 2005 dodge ram, and I just wanted to let my Expert know that he hit the nail squarely on the head with his answer. I wanted to thank him again.

GregPittsburgh, PA

Just a quick line to tell you how pleased I am to have my brakes working properly after all this time. Your answer was what I needed. I would certainly recommend you highly. God bless!

JerryHolts Summit, MO

Thank you so much for your answer. My initial estimate was $325; I got it done for $100 - part and labor.

Lynn B.Ormond Beach, FL

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

< Previous | Next >

Meet the Experts:

Don - Mo Lurch

Don - Mo Lurch

Aftermarket & Factory Electronics

542 satisfied customers

Cert. Chrysler Warnty, Heavy Line Mech, Mobile Electronics. Sales, Installation & Repair for 30 years

Chris (aka - Moose)

Chris (aka - Moose)

Technician

568 satisfied customers

16 years of experience

Paul M ASE Master

Paul M ASE Master

ASE Master Tech

118 satisfied customers

ASE Master Tech 20+ Years

Ivan

Ivan

ASE Certified Master Technician

56 satisfied customers

ASE Master Tech w/ 20+ years in the field. Self employed for 9 years. Member of AUTOLAB radio show.

Amedee

Amedee

Chrysler Technician

956 satisfied customers

ASE certified Technician advanced level specialist. Wisconsin certified emissions state inspector

Jerry

Jerry

Master Mechanic

696 satisfied customers

ASE Master tech. 30+ years mechanic, shop forman, service manager

Ron

Ron

ASE Certified Technician

419 satisfied customers

#@ years in the Automotive repair field.

< Previous | Next >

Related Chrysler Questions
Chrysler Pt loser: K I have a 2002 ot cruiser and it's not
K I have a 2002 ot cruiser and it's not starting! Checked timing on CS and crank, ok" put new crank sensor and cam sensor, and new rebuilt ECM ! And new cool! Nothing I do is changing the fact that it… read more
sprinkles08
sprinkles08
Technician
High School or GED
11 satisfied customers
pt cruiser: check engine..car started sputtering..accelerate..autozone
My girlfriend has a 07 pt cruiser and the check engine came on. The car started sputtering when you accelerate so I took it to autozone. And they checked the codes and it called for camshaft position … read more
Eric
Eric
Retired
N/A
14,436 satisfied customers
2002 Chrysler Sebring: pcm..cam sensor..the crank sensor..timing chain
I have a 2002 Chrysler Sebring 2.7 v-6. The#6,#3,and #5 coil packs are not receiving a signal from the pcm. I have changed the cam sensor, the crank sensor and and cleaned the grounds. No broken wires… read more
Dodgerench
Dodgerench
Driveability Tech
Vocational, Technical or Trade Scho
409 satisfied customers
dodge: my shop..running well..compression is 170 psi across the board.
this question is for a chrysler \ dodge dealer employeed tech with min 10 year experience only, thank you all others ! IN my shop I have a 2000 chryler concorde with 190.000 miles, it has a 2.7 litre … read more
Dodgerench
Dodgerench
Driveability Tech
Vocational, Technical or Trade Scho
409 satisfied customers
Rebuilt engine..car,new sensers camshaft and crankshaft.engine..rough
just had rebuilt engine put in car,new sensers camshaft and crankshaft.engine light on with camshaft and crankshaft codes .car has rough starts ups and when driving .when at a stop car tends to rumble… read more
Robert R
Robert R
Auto Technician
Vocational, Technical or Trade Scho
879 satisfied customers
2002 Pt Cruiser touring: 000 miles..heated..compression..engine swap
Hi I have a 2002 Pt Cruiser touring with 120,000 miles on it. My friend over heated the engine to the point of no compression. I did an engine swap on it. everything thing went smoothly. now the new e… read more
jeepmopar76
jeepmopar76
Master tech
Vocational, Technical or Trade Sc
4 satisfied customers
2001 Chrysler Sebring: rebuilt..crank..bearing..the Cam Sensor & it
I purchased a 2001 Chrysler Sebring 2.7 with a bad motor I rebuilt the engine new crank & bearing, new rings. Car would not start so i unplugged the Cam Sensor & it started. It cranks for 5 to 10 seco… read more
sprinkles08
sprinkles08
Technician
High School or GED
11 satisfied customers
Pt cruiser turbo: all factory sensors cam..crank..alignment
hello keep getting code p0344 for 03 pt cruiser turbo pretty much change all factory sensors cam and crank and cam magnet, checked timing alignment 3 times its ok updated pc. problem started after rep… read more
sprinkles08
sprinkles08
Technician
High School or GED
11 satisfied customers
limited: used engine in a 02 chry..rev..rod knocking in it..ran fine
i put a used engine in a 02 chry. 300 & now i have a running prblem with it starting & when it reaches 2000 rpm it starts to run funny like it has a rev limiter the other motor ran just fine besides i… read more
brownjeff
brownjeff
Associate Degree
13,873 satisfied customers
2004 Chrysler Sebring: the cam and crank position sensors..injectors
Had a rebuildt 2.7 put in my 2004 Chrysler Sebring and the mechanic thinks that the cam and crank position sensors are not working correctly because something is maybe different mechanically with the … read more
BOBBYSS
BOBBYSS
TECHNICIAN/ADVISOR
Associate Degree
8,343 satisfied customers
2005 PT Cruiser: the Check Engine light came..pulling..Timing Belt
After replacing the Camshaft Position Sensor on a 2005 PT Cruiser 2.4 non turbo with 63k miles, the car drove fine for one trip and the Check Engine light came back on. My wife described the car bucki… read more
DODGETECH2875
DODGETECH2875
Vocational, Technical or Trade Scho
1,004 satisfied customers
2001 sebring: wont start unless..cam sensor is..engine wont..rpms
2001 sebring wont start unless cam sensor is unplugged and takes about 10 secs before it will start. The engine wont go above 2900 rpms.… read more
sprinkles08
sprinkles08
Technician
High School or GED
11 satisfied customers
2001 chrysler sebring: crank..up runs fine except at 2900 rpm..rev
2001 chysler sebring 2.7 convertable check eng light on cam sensor code put new cam sensor in will not start put old sensor back in still has long long crank untill it fires up runs fine except at 290… read more
Rmldaytona
Rmldaytona
ASE certified technician
College
1,050 satisfied customers
restarted..turn on key switch..3 time and engine light..checked twice
have a 1994 chyrsler engine just shut off had to turn the key off and then back on car restarted ok. Just did the turn on key switch the 3 time and engine light sent this code 12255 checked twice what… read more
sprinkles08
sprinkles08
Technician
High School or GED
11 satisfied customers
Dodge magnum: I have a 2004 dodge 4.7 magnum 1500 truck..engines
I have a 2004 dodge 4.7 magnum 1500 truck with a 4.7 dodge magnum motor (2002) I have put into it. Both engines running when i pulled them. Now i get no fire at sparkplug. Tried new crankshaft sensor … read more
Dodgerench
Dodgerench
Driveability Tech
Vocational, Technical or Trade Scho
409 satisfied customers
2000 Concorde: rebuilt..knocking..bent crankshaft due..faulty material
Have a 2000 Concorde 2.7- Engine was rebuilt about 3 years ago. Started faint knocking, mechanic found bent crankshaft due to faulty material in previous rebuild. Replaced totally free of charge. Now … read more
jeepmopar76
jeepmopar76
Master tech
Vocational, Technical or Trade Sc
4 satisfied customers
2001 Intrepid: 97,000 miles..crank sensor..runs good..engine lite
2001 Intrepid, 2.7 engine, 97,000 miles...Dies and act like a skip just before dieing.....Code P1391......Have changed crank sensor twice and runs good at times and ck. engine lite....Would not start … read more
Dodgerench
Dodgerench
Driveability Tech
Vocational, Technical or Trade Scho
409 satisfied customers
97 chrysler cirrus lx: accelerating..pulled 3 plug wires..Timing belt
97 chrysler cirrus lx 2.5 v6 24 valve. Engine starts & runs with a minor miss, smooths out some after warming up, main problem is when accelerating quickly it falls on its face,missing like you just p… read more
b5demon
b5demon
Automotive Technician
Vocational, Technical or Trade Scho
1,522 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x