Boat

Have Boat Questions? Ask a Boat Repair Expert.

Connect one-on-one with {0} who will answer your question

Related Boat Questions
I have a 1996 Mercury 90 HP 2-Stroke which had a fuel line
I have a 1996 Mercury 90 HP 2-Stroke which had a fuel line issue that caused me to stall out and flood the engine really badly. I was drifting and couldn't the engine started so I was cranking pretty hard on the throttle control. I finally got the engine started by now it is only topping out at about 4K RPM's and I can tell that something isn't opening up properly. I have checked throttle cables, timing, and maximum throttle stop which are all fine. I am almost sure that it's an issue with one of the carburetors at this point that either is out of synch or just not opening properly even though the throttle control and throttle mechanism are going to full. … read more
Noel Schembri
Noel Schembri
Marine mechanic
Diploma
2,745 satisfied customers
2008 Mercury four stroke 115 EFI. This past year it sat for
2008 Mercury four stroke 115 EFI. This past year it sat for 6 mos before use. When I started using it again. It would idle fine but would not go over 8MPH or 2600 RPM's. (Peak performance 28MPH, 5000 … read more
Charles
Charles
Certified Mercury Tech
5,752 satisfied customers
I have a cobra 4.3 with a cobra outdrive. It has a 14 1/2 x
I have a cobra 4.3 with a cobra outdrive. It has a 14 1/2 x 19 prop. I was given a ss prop, 15 1/4 x 19. Can I use this prop and what is the difference. I do a lot of trolling and occasionaly pull the… read more
Jason
Jason
Marine Mechanic
23,333 satisfied customers
Ercruiser certified? I have 2 7.4 454 mags mpi horizon in my
I have 2 7.4 454 mags mpi horizon in my 2000 Sea Ray Sundancer. Numbers are 0L395022 and 0L395002. 780 hours. The port engine will not reach 2600 rpms. I''ve changes plugs, wires, cap, rotor, fuel filter. Pulled plenum looking for vacuum leaks. 135 psi compression. Nothing wrapped around prop shaft. Did find some oil residue around the intake next to MAP sensor. … read more
Jason
Jason
Marine Mechanic
23,333 satisfied customers
I have QSB 380s in a 2008 SeaRay 40DA. What is the highest
Hi I have QSB 380s in a 2008 SeaRay 40DA. What is the highest RPM you would cruise at? I see 22.5 kts at 2600 RPM and was wondering if 2600-2650 is ok to cruise for 3 hours Thanks… read more
Jason
Jason
Marine Mechanic
23,333 satisfied customers
2005 yamaha 225 4 strokes . 290 hrs . launched boat just idling
2005 yamaha 225 4 strokes . 290 hrs . launched boat just idling out of channel starboard motor died . we go anchor starts back up when give it gas then dies again . changed both fuel filter water /fue… read more
Jason
Jason
Marine Mechanic
23,333 satisfied customers
Is there any way to remove the low speed circuit so it would
Is there any way to remove the low speed circuit so it would run on all 4. About 2600 rpm my 125 goes from firing on 2 cyls to all 4. It is on a pontoon and we have a hard time taking a slow ride?… read more
Jeff G.
Jeff G.
Marine Mechanic
Vocational, Technical or Trade Scho
4,730 satisfied customers
i am in the process of buying a 46 ft maxum 2001 with diamond
i am in the process of buying a 46 ft maxum 2001 with diamond series 450C engines, specifically 6cta8.3 m3 1200 hours 3 specific questions 1) At start up the engine fire up fast and immediatly, but th… read more
Jason
Jason
Marine Mechanic
23,333 satisfied customers
My jet ski runs fine for a few seconds, then bogs down a few
My jet ski runs fine for a few seconds, then bogs down a few seconds then repeats over and over. I recently purchased the ski from a marine mechanic. He had just rebuilt both carbs and put in all new … read more
Jeremy R.
Jeremy R.
5,362 satisfied customers
I won a 1991 Donzi F23. The boat was repowerd in 2011 with
I won a 1991 Donzi F23. The boat was repowerd in 2011 with a new engine. The RPM meter reads 3100 at full throttle during normal operation. The RPM reading at full throttle for the originaal engine wa… read more
K. Kergan
K. Kergan
Inboard/Outboard Mechanic
Vocational, Technical or Trade Scho
1,031 satisfied customers
I have a Sealine S41 with Kad 300s on outdrives, DPs. On trying
I have a Sealine S41 with Kad 300s on outdrives, DPs. On trying to start the port engine with the starboard fired up no problem, no ignition switch. Turned off the starboard, and went down to the engi… read more
orcamarine
orcamarine
Proprietor
Vocational, Technical or Trade Scho
7 satisfied customers
i have a trophy walk around 2052 with D1.7L DTI ENGINE its
i have a trophy walk around 2052 with D1.7L DTI ENGINE its running hot and wont pull its top rpm Im thinking it is over propped does any body no the correct prop size and how many Knots i should get o… read more
Jason
Jason
Marine Mechanic
23,333 satisfied customers
I have a Volvo Penta TAMD 74L, 2003 Model. Am researching for
I have a Volvo Penta TAMD 74L, 2003 Model. Am researching for new props to get more speed and need rated horse power (I believe it to be 430) and the governed Rpm.… read more
Jason
Jason
Marine Mechanic
23,333 satisfied customers
I have a 1998 Rinker 232 Captiva boat with a 7.4 liter motor.
I have a 1998 Rinker 232 Captiva boat with a 7.4 liter motor. At full throttle I show 4200 RPM. I have changed props a couple of times and only get about 45mph. Is their something I can change in the … read more
Whitecap36
Whitecap36
Service Manager/Technician
Vocational, Technical or Trade Scho
1,557 satisfied customers
i have 90 model 150 that will not turn but 2600 rpms replaced
i have 90 model 150 that will not turn but 2600 rpms replaced all fuel lines filters and lower fuel pump engine runs up to 3300 sometimes but acts like u pull throttle back and slows to 2500 to 2600… read more
Jeff G.
Jeff G.
Marine Mechanic
Vocational, Technical or Trade Scho
4,730 satisfied customers
My port side BF115 is running wide open at only about 4200
My port side BF115 is running wide open at only about 4200 RPM. Starbord is at about 5000. All compression is good. I suspect maybe a little stretch in throttle cables. Any ideas on how to get them bo… read more
Jeff G.
Jeff G.
Marine Mechanic
Vocational, Technical or Trade Scho
4,730 satisfied customers
I recently paid over 7k to have my Bravo 3 port engine sterndrive
I recently paid over 7k to have my Bravo 3 port engine sterndrive lower unit rebuilt and the coupler on my 7.4 liter MPI engine replaced. I just received the boat back and there are a few issues: 1) P… read more
Jeremy R.
Jeremy R.
5,362 satisfied customers
Ive got a ford 351 v8 in my boat, and am curious as to what
I've got a ford 351 v8 in my boat, and am curious as to what the approximate red line is. Also, at what rpm will the engine cruise best? Thanks… read more
Pappy's Sales and Service
Pappy's Sales and Service
Vocational, Technical or Trade Scho
586 satisfied customers
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help.

Mary C.Freshfield, Liverpool, UK

This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!!

AlexLos Angeles, CA

Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult.

GPHesperia, CA

I couldn't be more satisfied! This is the site I will always come to when I need a second opinion.

JustinKernersville, NC

Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around.

EstherWoodstock, NY

Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know.

RobinElkton, Maryland

He answered my question promptly and gave me accurate, detailed information. If all of your experts are half as good, you have a great thing going here.

DianeDallas, TX

< Previous | Next >

Meet the Experts:

Ted G.

Ted G.

Rigger, Diagnostician

3,161 satisfied customers

40 years boating, Safe boating instruct., Offshore Race promoter, Failure Analysis, Expert Witness

Dominick

Dominick

Marine Mechanic

1,009 satisfied customers

25 Years Experience as Mechanic, 20 Yrs Boat Yard Owner/Mechanic, Factory Certified

John White

John White

Marine Mechanic

306 satisfied customers

11 years experience working on outboards, inboards, sterndrives & pwcs

Jason

Jason

Marine Mechanic

23,333 satisfied customers

Degree in Marine Technology. Gas and diesel marine mechanic.

Tan

Tan

MerCruiser Certified Technician

11,409 satisfied customers

40 yrs. experience with complete engine repairs both inboard/outboard and MerCruiser Certified Technician.

Jeff G.

Jeff G.

Marine Mechanic

4,730 satisfied customers

42 years experience, Certified Master Technician, All Major Outboards, Sterndrives, Hi-Performance

Captain Dave

Captain Dave

Marine Mechanic

2,672 satisfied customers

USCG Licensed Captain, 20+ Years Boating, Fishing, Maintenance and Repair Experience

< Previous | Next >

Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.

Show MoreShow Less

Ask Your Question

x