How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site. Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Tyler Z. Your Own Question
Tyler Z.
Tyler Z., Appliance Doc
Category: Appliance
Satisfied Customers: 82038
Experience:  9+ years being an appliance technician with factory training.
Type Your Appliance Question Here...
Tyler Z. is online now
A new question is answered every 9 seconds

My Maytag bravos x washer's lid lock indicator light blinks

Customer Question

My Maytag bravos x washer's lid lock indicator light blinks after the sensor cycle and won't complete cycle.
Submitted: 2 years ago.
Category: Appliance
Expert:  Tyler Z. replied 2 years ago.
The lid lock light flashing just means there is an error detected. So I just want to start by saying if I was in your house, I'd go through diagnostics and see what error code you're getting, but I've tried to explain how to do this to many people and for some reason they just can't get the sequence to work. So by far, the most likely thing that will cause this issue is your actuator failing or possibly your drain pump being clogged up. Both the drain pump and the actuator motor are located below the tub and if you're wondering, the actuator is the part that switches the shifter next to the motor. You'll want to first check the drain pump so unplug the washer and tip the unit backwards a bit so you can get underneath. Follow the drain hose to locate the drain pump under the tub and you'll want to remove as much water out of the tub as you can because whatever is left inside will come pouring out once you remove the drain pump. Have a wet vac or lots of towels ready to soak up the water that comes out. Check for a blockage and remove anything inside the pump that you find. Put everything back together and try the washer again. If you still get the same problem, onto the actuator we go.To access the actuator you need to unplug the washer, tip the washer backwards, and remove the 2 screws going into the plastic cover near the back left corner. That will allow you to access the motor and the actuator to the right of the motor. Remove the screws going into the actuator and replace the actuator. Below is a link to the part you'd need to order for your model. CLICK HERE for part as well as a video at the bottom of the link that shows you how to replace the partNow, if you wanted to give it a shot and see if you can pull up an error code, here is the sequence you'll need to go through to display the error code.1. Be sure the washer is in standby mode (plugged in with all indicators off). (press and hold the start/cancel button for 3 seconds to turn everything off)2. Perform the following sequence of movement using the cycle selector knob. NOTE: AFTER RESET, sequence “a” through “e” must be completed within 6 seconds.RESET - Rotate cycle selector knob counterclockwise to clear sequence.a. Rotate cycle selector knob clockwise one click and wait 1⁄2 second. b. Rotate cycle selector knob clockwise one click and wait 1⁄2 second.c. Rotate cycle selector knob clockwise one click and wait 1⁄2 second. d. Rotate cycle selector knob counter-clockwise one click and wait 1⁄2 second. e. Rotate cycle selector knob clockwise one click and wait 1⁄2 second. Now you are in diagnostics. Turn the knob until just the "DONE" LED is illuminated. Push START. Now turn the dial one click and now the error code is displayed in the form of LEDs along the progress line. Just note which lights appear and let me know and I can tell you what error you're getting. There will be 2 sets of lights that appear and I need both sets to know what error you're getting.We are on the honor system here. Please remember to rate my service before you leave today. If you need anything else, just let me know. You can continue asking follow-up questions at no additional charge after rating my service if you still need assistance.
Customer: replied 2 years ago.
Thanks for your answer. I checked the pump. Cleaned it out and made sure nothing was in it. When we went to run a load it did the same thing, but locked twice before blinking. Decided to try the diagnosis. Got that started and it goes through multiple steps and seems to stop and be finished at the spin cycle without fully spinning. Says it is done but can not do anything or retrieve codes. Not sure what next.
Expert:  Tyler Z. replied 2 years ago.
I would replace the actuator if you can't pull up an error code to confirm the issue. The actuator is by far the most likely culprit if it can't shift into the transmission into the gear that is intended. That will cause the washer to lock, unlock, and then re-lock before flashing the locked light because it's not sensing the correct position on the actuator when trying to start a cycle.
Customer: replied 2 years ago.
It actually tried to run a load but now the barrel moves a lot and it leaks. Not sure what to do.
Expert:  Tyler Z. replied 2 years ago.
I'm not sure either because that wasn't the same conditions you had before so possibly something got messed up when you removed and re-installed the drain pump. If this isn't a naturally occurring issue you're going to need a technician out there to examine the problem if you can't locate the issue yourself.