How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask sprinkles08 Your Own Question
sprinkles08
sprinkles08, ASE Certified Technician
Category: UK Car
Satisfied Customers: 22525
Experience:  ASE Master and Advanced level certified. Factory trained with 15 years dealership experience
9825021
Type Your UK Car Question Here...
sprinkles08 is online now
A new question is answered every 9 seconds

Chrysler Pacifica: hiI have replaced camshaft

Customer Question

hi
I have replaced camshaft for pacifa 3.5 2004 . and I put second hads from crysler 300 3.5 l. looks the same fly wheel as well looks the same , but I don't have spark , can I get wiring for pacifika pcm?
Submitted: 2 years ago.
Category: UK Car
Expert:  sprinkles08 replied 2 years ago.
Hello and welcome to JustAnswer!
You may have quite a few things going on. You could have a wiring issue, lack of cam or crank signal, an ASD circuit issue, or the problem may be cam timing related. Incorrect cam timing or mismatched components will prevent spark.
What year car did the engine come from?
Customer: replied 2 years ago.
Cam shaft I took from 300 Chrysler 3.5
Expert:  sprinkles08 replied 2 years ago.
What year was the car that the engine came from?
Customer: replied 2 years ago.
2005
Customer: replied 2 years ago.
I did not conect alternator is that issue?
Customer: replied 2 years ago.
And I took pcm and put in to other Pacifica. Pcm works starts just for 2 sec becouse mobilizer , but works
Customer: replied 2 years ago.
Do yuo think alternator issue or camshaft, becouse before replacment car was runing
Expert:  sprinkles08 replied 2 years ago.
It's not the alternator or cam.
Does your powertrain control module have four connectors or two?
Customer: replied 2 years ago.
4
Expert:  sprinkles08 replied 2 years ago.
If you reconnect everything, clear fault codes, crank the starter for ten solid seconds and read codes does anything set?
Customer: replied 2 years ago.
One minute
Customer: replied 2 years ago.
P0123. P0108
Customer: replied 2 years ago.
That I have
After reset and cranking
Expert:  sprinkles08 replied 2 years ago.
Do you have injector pulse?
Customer: replied 2 years ago.
No
Customer: replied 2 years ago.
I go look for camshaft. Timing
Customer: replied 2 years ago.
On gear box fly wheel must be holes ?
Customer: replied 2 years ago.
Timing looks good and no codes whats wrong
Customer: replied 2 years ago.
When I check 5v suplay , ingnition on looks good , but when I check signal it shows to 5 v . Must bee this way or not?
Expert:  sprinkles08 replied 2 years ago.
Your'e seeing 5v on a sensor signal wire? What sensor?
Customer: replied 2 years ago.
On bouth crank and cam On signal when ingnition on , but when start to crank drops to 0.6 v
Customer: replied 2 years ago.
Just I thoutgh signal must bee 0.0 v when ignition is on not 4.96v
Expert:  sprinkles08 replied 2 years ago.
You'll have 5v on the signal wires if the sensors are unplugged and key is on.
Do you have an actual scan tool?
Customer: replied 2 years ago.
Just I thoutgh signal must bee 0.0 v when ignition is on not 4.96v.
Customer: replied 2 years ago.
Do yuo have pcm schema for Pacifica
Customer: replied 2 years ago.
yes do have . and look cam shaft and timing is good . signals 0.6 v . wiring 0.3 resistance
what alse?
asd what that mean can get wiring for pacifica?
Expert:  sprinkles08 replied 2 years ago.
What is cam/crank difference while cranking?
Customer: replied 2 years ago.
difference what do yo mean?
Customer: replied 2 years ago.
signal diference V?
Expert:  sprinkles08 replied 2 years ago.
Cam/crank sync degrees.
Customer: replied 2 years ago.
Signal I have cam 0.6v but crank 2.0-2.6 v signal
Customer: replied 2 years ago.
How to check crank sencor ?
Expert:  sprinkles08 replied 2 years ago.
Use the scan tool to monitor cam/crank sync degrees while cranking the engine. What does it show?
Customer: replied 2 years ago.
I don't have that tool can I buy
Expert:  sprinkles08 replied 2 years ago.
You said you had a scan tool. What is the brand and model of what you're using?
Customer: replied 2 years ago.
Obd 2 can I talk tomorrow ?
Expert:  sprinkles08 replied 2 years ago.
Yes.