How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask john Your Own Question

john
john, The Car Guy
Category: Toyota
Satisfied Customers: 12953
Experience:  ase tech over 15 years in the field
6149662
Type Your Toyota Question Here...
john is online now
A new question is answered every 9 seconds

1999 TOYOTA CAMRY 2.2 L ( 4 CLY. ) INSTRUCTIONS ON REMOVAL

Customer Question

1999 TOYOTA CAMRY 2.2 L ( 4 CLY. )
INSTRUCTIONS ON REMOVAL AND REINSTALL OF TRANSMISSION, PLEASE . THANK YOU !
Submitted: 4 years ago.
Category: Toyota
Expert:  john replied 4 years ago.
graphicgraphic
REMOVAL
  1. REMOVE BATTERY
  2. REMOVE AIR CLEANER ASSEMBLY
  3. DISCONNECT THROTTLE CABLE



  1. w/ CRUISE CONTROL: REMOVE CRUISE CONTROL ACTUATOR
    1. Disconnect the connector.
    2. Remove the 3 bolts and disconnect cruise control actuator with the bracket.



  1. DISCONNECT OIL COOLER HOSE
  2. DISCONNECT VEHICLE SPEED SENSOR CONNECTOR
  3. DISCONNECT PARK/NEUTRAL POSITION SWITCH CONNECTOR
  4. DISCONNECT SHIFT SOLENOID VALVE NO.1 AND NO.2 CONNECTOR
  5. DISCONNECT SHIFT SOLENOID VALVE SL CONNECTOR



  1. REMOVE 2 FRONT SIDE ENGINE MOUNTING BOLTS Torque: TMC made: 80 Nm (820 kgf-cm, 59 ft. lbs.) TMMK made:

Green color bolt: 66 Nm (670 kgf-cm, 48 ft. lbs.)
Silver color bolt: 44 Nm (450 kgf-cm, 32 ft. lbs.)

  1. DISCONNECT 2 GROUND CABLES



  1. REMOVE STARTER
    1. Disconnect the connector and remove the nut.
    2. Remove the 2 bolts, shift cable clamp and starter. Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.)
  1. REMOVE 3 TRANSAXLE-TO-ENGINE BOLTS Torque: 66 Nm (670 kgf-cm, 48 ft. lbs.)



  1. REMOVE EXHAUST MANIFOLD STAY Remove the 2 bolts and exhaust manifold stay. Torque: 42 Nm (430 kgf-cm, 31 ft. lbs.)
  2. REMOVE TRANSAXLE-TO-ENGINE BOLT Torque: 66 Nm (670 kgf-cm, 48 ft. lbs.)
  3. REMOVE ENGINE HOOD
    1. Disconnect the washer pipe.
    2. Remove the 4 bolts and engine hood. Torque: 14 Nm (145 kgf-cm, 10 ft. lbs.)
  1. RAISE AND SUPPORT VEHICLE SECURELY
  2. REMOVE FRONT WHEELS Torque: 103 Nm (1,050 kgf-cm, 76 ft. lbs.)
  3. REMOVE ENGINE UNDER COVER AND CENTER ENGINE UNDER COVER



  1. DISCONNECT SHIFT CONTROL CABLE
    1. Remove the nut and disconnect the shift control cable from the park/neutral position switch. Torque: 15 Nm (150 kgf-cm, 11 ft. lbs.)
    2. Remove the clip and disconnect the shift control cable from the bracket.



  1. REMOVE DIFFERENTIAL FLUID DRAIN PLUG AND GASKET HINT: At the time of installation, please refer to the following item. Replace the used gasket with a new gasket.
  2. DRAIN DIFFERENTIAL FLUID
  3. REMOVE LH AND RH FENDER APRON SEALS
  4. REMOVE LH AND RH DRIVE SHAFTS



  1. REMOVE EXHAUST FRONT PIPE
    1. Remove the 2 nuts and exhaust front pipe clamp. Torque: 33 Nm (330 kgf-cm, 24 ft. lbs.)
    2. Remove the 2 bolts and exhaust pipe No. 1 support bracket. Torque: 33 Nm (330 kgf-cm, 24 ft. lbs.)
    3. Remove the 3 nuts. Torque: 62 Nm (630 kgf-cm, 46 ft. lbs.) HINT: At the time of installation, please refer to the following item. Replace the used nuts with new ones.
    4. Remove the 2 bolts, nuts and front exhaust pipe. Torque: 56 Nm (570 kgf-cm, 41 ft. lbs.) HINT: At the time of installation, please refer to the following item. Replace the used nuts with new ones.
    5. Remove the 2 gaskets. HINT: At the time of installation, please refer to the following item. Replace the used gaskets with new ones.



  1. REMOVE FRONT SIDE ENGINE MOUNTING INSULATOR BOLT Torque: TMC made: 80 Nm (820 kgf-cm, 59 ft. lbs.) TMMK made:

Green color bolt: 66 Nm (670 kgf-cm, 48 ft. lbs.)
Silver color bolt: 44 Nm (450 kgf-cm, 32 ft. lbs.)



  1. REMOVE REAR SIDE ENGINE MOUNTING NUT
    1. Remove the 2 grommets.
    2. Remove the 3 nuts. Torque: 66 Nm (670 kgf-cm, 48 ft. lbs.)



  1. REMOVE LEFT SIDE TRANSAXLE MOUNTING NUT
    1. Remove the 2 grommets.
    2. Remove the 2 nuts. Torque: 80 Nm (820 kgf-cm, 59 ft. lbs.)



  1. REMOVE STEERING GEAR HOUSING
    1. Remove the 4 bolts, LH and RH stabilizer bar brackets and bushings. Torque:119 Nm (195 kgf-cm, 14 ft. lbs.)
    2. Remove the front stabilizer bar.
    3. Remove the 2 steering gear housing mounting bolts and nuts. Torque: 181 Nm (1,850 kgf-cm, 134 ft. lbs.)



  1. TIE STEERING GEAR HOUSING TO REAR ENGINE MOUNTING BRACKET BY CORD OR EQUIVALENT
  2. ATTACH ENGINE SLING DEVICE TO ENGINE HANGERS CAUTION: Do not attempt to hang the engine by hooking the chain to any other part.
  3. REMOVE FRONT FRAME ASSEMBLY



  1. Remove the 2 bolts and steering return pipe mounting brackets. Torque: 10 Nm (100 kgf-cm, 7 ft. lbs.)



  1. Remove the screws and turn over the front side of the LH and RH fender liners.



  1. Remove the screws and turn over the rear side of LH and RH fender liners.




  1. Remove the 6 bolts and 4 nuts. Torque: 19 mm head bolt: 181 Nm (1,850 kgf-cm, 134 ft. lbs.) 14 mm head bolt: 32 Nm (330 kgf-cm, 24 ft. lbs.) Nut: 36 Nm (370 kgf-cm, 27 ft. lbs.)
  2. Remove the front frame assembly.
    1. SUPPORT TRANSAXLE WITH A TRANSMISSION JACK



    1. REMOVE FRONT SIDE STIFFENER PLATE TMMK made: Remove the nut, 2 bolts and stiffener plate. Torque: 42 Nm (430 kgf-cm, 31 ft. lbs.) TMC made: Remove the 3 bolts and stiffener plate. Torque: 42 Nm (430 kgf-cm, 31 ft. lbs.)
    2. REMOVE REAR END PLATE
      1. Remove the 2 bolts and No. 1 exhaust pipe support bracket. Torque: 19 Nm (195 kgf-cm, 14 ft. lbs.)
      2. Remove the 2 bolts and rear end plate with oil pan insulator. Torque: 25 Nm (250 kgf-cm, 18 ft. lbs.)



    1. REMOVE TORQUE CONVERTER CLUTCH MOUNTING BOLT Turn the crankshaft to gain access to each bolt, remove the 6 bolts with holding the crankshaft pulley set bolt by a wrench. Torque: 27 Nm (280 kgf-cm, 20 ft. lbs.) HINT: At the time of installation, please refer to the following item. First the install black colored bolt and then the 5 other bolts.
    2. REMOVE REAR SIDE STIFFENER PLATE
      1. Remove the 2 bolts and manifold stay. Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.)
      2. Remove the 4 bolts and stiffener plate. Torque: 39 Nm (400 kgf-cm, 29 ft. lbs.)
    1. REMOVE TRANSAXLE ASSEMBLY Separate the transaxle and engine, and lower the transaxle.

INSTALLATION



  1. CHECK TORQUE CONVERTER CLUTCH INSTALLATION Using a scale and a straight edge, measure to the distance from the installed surface to the transaxle housing. Correct distance: 13.0 mm (0.512 inch) or more
  2. TRANSAXLE INSTALLATION Installation is in the reverse order of removal. HINT: After installation, check and inspect items as follows.
    • Fluid level
    • Front wheel alignment
    • Road test of the vehicle
    • Engine hood

 



 

JustAnswer in the News:

 
 
 
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
 
 
 

What Customers are Saying:

 
 
 
  • THANK YOU, THANK YOU, THANK YOU!! I've got my baby back. Tomorrow I will get a tank of high octane, remove the top, go for a long long ride and enjoy my car. THANK YOU! Jughead USA
< Last | Next >
  • THANK YOU, THANK YOU, THANK YOU!! I've got my baby back. Tomorrow I will get a tank of high octane, remove the top, go for a long long ride and enjoy my car. THANK YOU! Jughead USA
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
  • This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!! Alex Los Angeles, CA
  • Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. GP Hesperia, CA
  • I couldn't be more satisfied! This is the site I will always come to when I need a second opinion. Justin Kernersville, NC
  • Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around. Esther Woodstock, NY
  • Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know. Robin Elkton, Maryland
 
 
 

Meet The Experts:

 
 
 
  • Chris (aka-Moose)

    Auto Technician

    Satisfied Customers:

    278
    16 years of experience
< Last | Next >
  • http://ww2.justanswer.com/uploads/MU/muddyford/2012-6-13_1204_1.64x64.png Chris (aka-Moose)'s Avatar

    Chris (aka-Moose)

    Auto Technician

    Satisfied Customers:

    278
    16 years of experience
  • http://ww2.justanswer.com/uploads/EU/eurotec/2012-6-11_13153_mpjaphoto.64x64.JPG Marty's Avatar

    Marty

    ASE Certified Technician

    Satisfied Customers:

    167
    ASE & Bosch Master Tech. 30 years experience.
  • http://ww2.justanswer.com/uploads/AM/amedee/2013-10-24_23656_Amedee1.64x64.jpg Amedee's Avatar

    Amedee

    Toyota Technician

    Satisfied Customers:

    1132
    ASE Master Technician advanced level specialist. Wisconsin certified emissions state inspector
  • http://ww2.justanswer.com/uploads/CA/caprio23/2014-4-30_201741_20121205122939.64x64.jpg Anthony's Avatar

    Anthony

    ASE Certified Technician

    Satisfied Customers:

    373
    ASE Master Automobile Technician with over 20 years exp. in this field.
  • http://ww2.justanswer.com/uploads/CR/crzydrvr00/2013-11-3_12123_246347.64x64.jpg Richard's Avatar

    Richard

    ASE Certified Technician

    Satisfied Customers:

    9
    Toyota tech. ASE Certified Technician
  • http://ww2.justanswer.com/uploads/SK/skyvisions/2012-6-9_23736_JACropped3.64x64.jpg Skyvisions's Avatar

    Skyvisions

    ASE Certified Technician

    Satisfied Customers:

    11403
    Toyota Master Diagnostic
  • http://ww2.justanswer.com/uploads/genchigenbutsu/2009-05-09_003043_cimg16431.jpg Genchi Genbutsu's Avatar

    Genchi Genbutsu

    Toyota Master Technician

    Satisfied Customers:

    3425
    Toyota Certified Master Diagnostic Technician, ASE Master Technician with L1 Advanced Engine
 
 
 

Related Toyota Questions