How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask BigBob Your Own Question

BigBob
BigBob, Shop manager/Service Manager
Category: Toyota
Satisfied Customers: 4837
Experience:  Shop Manager with 25 years experience
13327319
Type Your Toyota Question Here...
BigBob is online now
A new question is answered every 9 seconds

94 toyota pickup: intake manifold..valve cover, head, and oil pan..rod

Resolved Question:

I am rebuliding a 22RE in a 94 toyota pickup. I need torque specs and tightning sequence (if aplicable) for the: intake manifold, exhaust manifold, valve cover, head, and oil pan. I need torque and clearence specs for the rod and main bearings.
Submitted: 4 years ago.
Category: Toyota
Expert:  BigBob replied 4 years ago.
Greetings,

1. Place the rocker arm assembly over the dowels on the cylinder head.
2 Install and tighten the head bolts gradually in 3 passes in the sequence shown.
3 Torque the bolts on the final pass.
Torque:58 ft.lbs. (800 kgf.cm, 78 Nm)



graphic

Intake


Install the 8 bolts, and 2 nuts. Torque the bolts and nuts.
Torque:14 ft.lbs. (195 kgf.cm,19 Nm )


graphic


graphic
graphic
graphic

See if this is everything if not let me know,

Bob
Customer: replied 4 years ago.
What is the clearence for the main and conecting rod bearings on the crank shaft? (for use with plastigauge)
Expert:  BigBob replied 4 years ago.
MEASURE crankshaft THRUST CLEARANCE
Using a dial gauge, measure the crankshaft thrust clearance while prying the crankshaft back and forth with a screwdriver.
Standard clearance: 0.02 - 0.22mm (0.0008 - 0.0087 in.)
Maximum clearance: 0.3mm (0.012 in.)
If the clearance is greater than maximum, replace the thrust washers as a set and/or crankshaft.
Thrust washer thickness:
Standard: 2.690 - 2.740 mm (0.1059 - 0.1079 in.)
0/S 1.25
2.753 - 2.803 mm (0.1084 - 0.1104 in.)
0/S 2.50
2.815 - 2.865 mm (0.1108 - 0.1128 in.)



MEASURE CONNECTING ROD THRUST
CLEARANCE
Using a dial gauge, measure the thrust clearance.
Standard clearance: 0.16-0.26mm (0.063 - 0.0102 in.)
Maximum clearance: 0.3mm (0.012 in.)
If clearance is greater than maximum, replace the connecting rod and/or crankshaft


Remove the rod cap.
(i) Measure the Plastigage at its widest point.
Standard clearance:
0.025 - 0.055 mm (0.0010 - 0.0022 in.)
Maximum clearance: 0.10mm (0.0039 in.)
If the clearance is greater than maximum, replace the bearings and/or grind the crank pins.
Undersized bearing: U/S 0.25
.

BigBob, Shop manager/Service Manager
Category: Toyota
Satisfied Customers: 4837
Experience: Shop Manager with 25 years experience
BigBob and 5 other Toyota Specialists are ready to help you

JustAnswer in the News:

 
 
 
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
 
 
 

What Customers are Saying:

 
 
 
  • THANK YOU, THANK YOU, THANK YOU!! I've got my baby back. Tomorrow I will get a tank of high octane, remove the top, go for a long long ride and enjoy my car. THANK YOU! Jughead USA
< Last | Next >
  • THANK YOU, THANK YOU, THANK YOU!! I've got my baby back. Tomorrow I will get a tank of high octane, remove the top, go for a long long ride and enjoy my car. THANK YOU! Jughead USA
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
  • This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!! Alex Los Angeles, CA
  • Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. GP Hesperia, CA
  • I couldn't be more satisfied! This is the site I will always come to when I need a second opinion. Justin Kernersville, NC
  • Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around. Esther Woodstock, NY
  • Thank you so much for taking your time and knowledge to support my concerns. Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know. Robin Elkton, Maryland
 
 
 

Meet The Experts:

 
 
 
  • Chris (aka-Moose)

    Auto Technician

    Satisfied Customers:

    278
    16 years of experience
< Last | Next >
  • http://ww2.justanswer.com/uploads/MU/muddyford/2012-6-13_1204_1.64x64.png Chris (aka-Moose)'s Avatar

    Chris (aka-Moose)

    Auto Technician

    Satisfied Customers:

    278
    16 years of experience
  • http://ww2.justanswer.com/uploads/EU/eurotec/2012-6-11_13153_mpjaphoto.64x64.JPG Marty's Avatar

    Marty

    ASE Certified Technician

    Satisfied Customers:

    167
    ASE & Bosch Master Tech. 30 years experience.
  • http://ww2.justanswer.com/uploads/AM/amedee/2013-10-24_23656_Amedee1.64x64.jpg Amedee's Avatar

    Amedee

    Toyota Technician

    Satisfied Customers:

    1132
    ASE Master Technician advanced level specialist. Wisconsin certified emissions state inspector
  • http://ww2.justanswer.com/uploads/CA/caprio23/2014-4-30_201741_20121205122939.64x64.jpg Anthony's Avatar

    Anthony

    ASE Certified Technician

    Satisfied Customers:

    373
    ASE Master Automobile Technician with over 20 years exp. in this field.
  • http://ww2.justanswer.com/uploads/CR/crzydrvr00/2013-11-3_12123_246347.64x64.jpg Richard's Avatar

    Richard

    ASE Certified Technician

    Satisfied Customers:

    9
    Toyota tech. ASE Certified Technician
  • http://ww2.justanswer.com/uploads/SK/skyvisions/2012-6-9_23736_JACropped3.64x64.jpg Skyvisions's Avatar

    Skyvisions

    ASE Certified Technician

    Satisfied Customers:

    11403
    Toyota Master Diagnostic
  • http://ww2.justanswer.com/uploads/genchigenbutsu/2009-05-09_003043_cimg16431.jpg Genchi Genbutsu's Avatar

    Genchi Genbutsu

    Toyota Master Technician

    Satisfied Customers:

    3425
    Toyota Certified Master Diagnostic Technician, ASE Master Technician with L1 Advanced Engine
 
 
 
Chat Now With A Toyota Mechanic
BigBob
BigBob
Toyota Mechanic
4837 Satisfied Customers
Shop Manager with 25 years experience