Join the 9 million people who found a smarter way to get Expert help

Recent appliance questions

I'm looking into outfitting a keg fridge and was

I'm looking into outfitting a keg fridge and was wondering what route I could go to do this on the economical side. Can I use any fridge and get some sort of kit?On a side note, is there a certain amount of time a keg of beer would stay good for in a fridge?

Read more

Tyler Z.

Appliance Technician

Bachelor's Degree

 
66,828 satisfied customers
Why does my 4 year old Vissani refrigerator shut off and go

Why does my 4 year old Vissani refrigerator shut off and go back on unexpectedly?

Read more

Appliance Guru

Service Technician

Associate Degree

 
22,622 satisfied customers
The icemaker on MN GT1SHTXMT03 Whirlpool refrigerator is

The icemaker on MN GT1SHTXMT03 Whirlpool refrigerator is making clicking sounds when arm is in on or off position. Nothing moves. There is no water in the ice maker. It appears the moving tines are in the horizontal position level with the fixed mechanism.

Read more

Tyler Z.

Appliance Technician

Bachelor's Degree

 
66,828 satisfied customers
I have an over the range microwave oven Model RMV1625SJ01 and

I have an over the range microwave oven Model RMV1625SJ01 and I don't have the template that's used to mount on the cabinet. I need help Please ... Thank you.JA: Sometimes appliance issues that that you think will be really complicated end up being easy to fix. The Appliance Technician I'm going to connect you with knows all the tricks and shortcuts. Tell me a bit more about what's going on so we can help you best.Customer: I need to know how far out from the wall I should drill the holes in the cabinet bottom. Measuring from the back of the microwave to the center of the hole is 8 1/2 inches. I don't want to drill the holes in the wrong spot. I don't have a template which would show me that info ... I would think.JA: Is there anything else important you think the Appliance Technician should know?Customer: Not at this time.JA: OK. Got it. I'm sending you to a secure page on JustAnswer so you can place the $5 fully-refundable deposit now. While you're filling out that form, I'll tell the Appliance Technician about your situation and then connect you two.

Read more

Tyler Z.

Appliance Technician

Bachelor's Degree

 
66,828 satisfied customers
I have a bosch hammer drill model 11240. The motor runs good

I have a bosch hammer drill model 11240. The motor runs good but it will not hammer. Any ideas on what the problem is?

Read more

Kelly

Owner/Technician

High School or GED

 
28,706 satisfied customers
Replacing icemaker panel (4681JA1006K) in LMX25981ST. But

Replacing icemaker panel (4681JA1006K) in LMX25981ST. But new panel is missing 3 screw holes: the top two and the middle one. The two bottom screw holes are there. Do I need to drill out for the other screws or what?

Read more

Kelly

Owner/Technician

High School or GED

 
28,706 satisfied customers
How do you replace the tempered glass on a Samsung Microwave

How do you replace the tempered glass on a Samsung Microwave SMH2117S/XAA-0001?

Read more

Stefan T

Service Technician

 
104 satisfied customers
Water keep filling the clothes washer after it stops. With

Water keep filling the clothes washer after it stops. With the washer lid closed or open but the mixing valve ON, the washing machine continues to fill with HOT (HOT) water even after the cycle is complete and the (wash complete) light comes on. If I shut the hot side off at the mixing valve of course it stops. The cold water side seem to be ok. There is a shut of for both hot and cold before the mix valve.. When I open the lid, everything should stop and it DOES NOT, it continues to fill with HOT water. I can put the water temp valve on any setting, cold, warm, hot and still it fills with HOT water.It's a sears (Kenmore) top loader purchased in 2012. It's a low-water washer according to the Manuel its a model 2130 TOP loader.What's wrong lol. I hate to call sears, going to charge me for two calls because he won;t have the parts with him.

Read more

Tyler Z.

Appliance Technician

Bachelor's Degree

 
66,828 satisfied customers
I have a model DV419AEW/XAA dryer that on the sensor dry cycle

I have a model DV419AEW/XAA dryer that on the sensor dry cycle gets hung up one one minute and keeps going. We have cleaned the vent and the blower housing, replace the sensor plates, replace the user control board and the main control board, and the thermistor as well. Still runs on, on the sensor dry cycle. Timed cycle not so much. What next to look at other than a new dryer?

Read more

Appliance Guru

Service Technician

Associate Degree

 
22,622 satisfied customers
View more appliance questions

How JustAnswer Works

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Pay nothing to your Expert if you're not satisfied.

In The News