JustAnswer > Chrysler
Ask A Question|Register|Login|Help
JustAnswer

Chrysler

Ask a Chrysler Question, Get an Answer ASAP!

Have your own Chrysler question?

25 Chrysler Mechanics are Online Now
characters left:
Not a Chrysler Question?

Related Chrysler Topics:

  • Arm
    • ,
  • Egr
    • ,
  • Iat
    • ,
  • Iac
    • ,
  • Pcv
    • ,
  • Tps
    • ,
  • Clip
    • ,
  • Cuts
    • ,
  • Free
    • ,
  • Fuel
Bookmark and Share

Question

I need to know how to replace the water outlet flange on a 1999 Chrysler concorde 2.7l

Submitted: 122 days and 2 hours ago via Mitchell1DIY.
Category: Chrysler
Value: $13
Status: CLOSED
+
Read More
Posted by brownjeff 122 days and 1 hours ago.

Answer

Here is the information on the outlet:

 

  1. Drain cooling system.
  2. Remove upper intake manifold.
  3. Remove screws attaching heater tube to outlet connector.
  4. Disengage tube from outlet connector-only enough for connector removal.

graphic
View Full Image

 

  1. Remove bolts attaching water outlet connector.
  2. Remove outlet connector.

INSTALLATION

  1. Clean sealing surfaces. Inspect gasket for tears and cuts. Replace as necessary.
  2. Install outlet connector and tighten bolts to 12 Nm (105 inch lbs.) .
  3. Inspect and replace heater supply tube O-ring as necessary.
  4. Lubricate O-ring and insert heater tube assembly into outlet connector. Tighten screws to 3 Nm (30 inch lbs.) .
  5. Install upper intake manifold.
  6. Fill cooling system.

122 days and 1 hours ago.

Reply

it tells me to remove the upper intake manifold. how difficult is that and how do I do it?

Accepted Answer

  1. Disconnect negative cable from battery remote jumper terminal.
  2. Remove air inlet resonator and inlet tube.
  3. Remove throttle cable and speed control cable from throttle arm and bracket.
  4. Remove throttle cable bracket.
  5. Disconnect electrical connectors from the following components:
    • Manifold Absolute Pressure (MAP) Sensor
    • Intake Air Temperature (IAT) Sensor
    • Throttle Position Sensor (TPS) Sensor
    • Idle Air Control (IAC) Motor
  1. Disconnect Vapor Purge hose, Brake Booster hose, Speed Control Servo, Positive Crankcase Ventilation (PCV) hose.
  2. Remove EGR tube.
  3. Loosen upper fastener at throttle body support bracket.

graphic
View Full Image

 

 

Fig. 35

  1. Remove upper fasteners from support brackets at right and left side of upper manifold (Fig. 35).
  2. Remove engine name cover from manifold by applying upward pressure to release retaining clip.
  3. Remove manifold attaching bolts.
  4. Remove upper manifold.

INSTALLATION

  1. Clean and inspect sealing surfaces. Gaskets can be reused, if free of cuts or tears. NOTE: Make sure fuel injectors and wiring harnesses are in correct position to not interfere with upper manifold installation
  2. Position upper manifold onto lower manifold.

graphic
View Full Image

 

Fig. 36

  1. Install manifold attaching bolts and tighten in sequence shown in (Fig. 36) to 12 Nm (105 inch lbs.) .
  2. Install fasteners to right and left side support brackets to manifold. Tighten lower fastener to 6 Nm (50 inch lbs.) . Then tighten upper fastener to 12 Nm (105 inch lbs.) .
  3. Install engine name cover to manifold.
  4. Tighten upper fastener at throttle body support bracket.
  5. Install EGR tube to manifold.
  6. Connect speed control servo hose, PCV hose, and vapor purge hoses.
  7. Connect electrical connectors to the following components:
    • Manifold Absolute Pressure (MAP) Sensor
    • Intake Air Temperature (IAT) Sensor
    • Throttle Position Sensor (TPS) Sensor
    • Idle Air Control (IAC) Motor
  1. Install throttle cable bracket.
  2. Install throttle and speed control cables to bracket and throttle arm.
  3. Connect negative cable to battery remote jumper terminal.

 

 

Picture
Expert: brownjeff
Pos. Feedback: 98.9 %
Accepts: 1001
Answered: 11/19/2009

ASE Certified Technician

17 years experience, ASE certified, dealership certified, Service Manager for 15 years,

+
Read More

Related Chrysler Questions

  • while putting in an aftermarket radio,i disconnected the yel...
  • I own a 94 plymouth voyager se and I want modify it with 200...
  • 2 in 1 questions motor sounds like a small airplane--a hard
  • 1995 cirrus 2.5l just replaced timing belt , water pump , ce...
  • How to remove upper dash pad to replace heater core on 2001
  • replaced belt surpentine & tensioner on my 2003 Town & Count...
  • I recently had my 2003 Town and counrty limited inspected.
  • i have a doge caravan 2004 just had the valve replaced that



Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.
Question List | Become an Expert | Terms of Service | Security & Privacy | About Us
© 2003-2010 JustAnswer Corp.