JustAnswer > Chevy
Ask A Question|Register|Login|Help
JustAnswer

Chevrolet

Ask a Chevy Question, Get an Answer ASAP!

Have your own Chevy question?

5 Chevy Mechanics are Online Now
characters left:
Not a Chevy Question?
Bookmark and Share

Question

how to replace a blinker switch in a 95 montecarlo?

Submitted: 403 days and 13 hours ago.
Category: Chevy
Value: $15
Status: AWAITING CUSTOMER ACTION

Answer

Hello,

 

Here are the instructions.

 

1994-96 Vehicles, Except 1994 Lumina

See Figures 3, 4, 5, 6 and 7

Click
View Full Image
Fig. 3: Remove the SIR coil assembly from the shaft
Click
View Full Image
Fig. 4: Remove the shaft lock retaining ring
Click
View Full Image
Fig. 5: Removing the components from the upper shaft
Click
View Full Image
Fig. 6: Remove the housing cover end cap
Click
View Full Image
Fig. 7: Turn signal switch removal

WARNING On vehicles with air bags, disable the SIR system. The vehicles wheels must be in the straight ahead position and the key must be in the LOCK position when removing or installing the steering column. Failure to do so may cause the SIR coil assembly to become uncentered and may result in otherwise unneeded SIR repairs.

  1. Disconnect the negative battery cable.
  2. If equipped, disable the SIR system, as outlined in of this repair guide.
  3. Remove the steering wheel, as outlined earlier in this information.
  4. Remove the SIR coil assembly retaining ring.
  5. Remove the SIR coil assembly. Let the coil hang freely if removal is not needed.
  6. Remove the wave washer.
  7. Remove the shaft lock retaining ring using tool J 23653-SIR to push down the shaft lock. Discard the ring.
  8. Remove the shaft lock, turn signal cancelling cam assembly and upper bearing spring.
  9. Remove the upper bearing inner race seat, then remove the inner race.
  10. Remove the multi-function lever, as follows:
    1. Make sure the lever is in the center or OFF position.
    2. Detach the electrical connection behind the lever.
    3. Pull the lever straight out.
  11. Remove the housing cover end cap. Using fingers, pry up and out at the location shown in the accompanying figure. Tilt the end cap away from the lock housing cover and sleeve assembly then remove.
  12. Unfasten the round washer head screw and the flat head screw.
  13. Remove the pivot and pulse dimmer switch assembly. Let the switch hang freely if removal is not needed.
  14. Using a suitable prytool, carefully pry OFF the hazard warning switch knob.
  15. Place the turn signal in the right turn position (up).
  16. Unfasten the three binding head cross recess screws.
  17. Remove the turn signal switch, as follows:
    1. Detach the turn signal connector from the bulkhead.
    2. Remove the wiring protector.
    3. Gently pull the wire harness through the column and remove the switch.
  18. Installation is the reverse of the removal procedure.
  19. Connect the negative battery cable, then enable the SIR system, as outlined in of this repair guide.

Picture
Expert: Virtual Wrench
Pos. Feedback: 99.6 %
Accepts: 
Answered: 10/15/2008

Master Tech

30 years/Master Tech. Foreign and Domestic

Related Chevy Questions

  • On a 1996 corsica does the rear defrost have a fuse it runs
  • We have a 1995 z28 Camaro, the front calipers are seizing.
  • my 95 tahoe wont engage into fourwheel drive
  • 91 corvett lost all power to dash lights will not turn over,
  • i changed the plug and the wire and the service engine ligh...
  • Yes i have a 1991 Cadillac sedan deville . I have taken the
  • where is the the security alarm located for a 1998 siverado?
  • m 99 monte carlo will not turn over when you turn the switch...



Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.
Question List | Become an Expert | Terms of Service | Security & Privacy | About Us
© 2003-2009 JustAnswer Corp.