JustAnswer > Chevy
Ask A Question|Register|Login|Help
JustAnswer

Chevrolet

Ask a Chevy Question, Get an Answer ASAP!

Have your own Chevy question?

18 Chevy Mechanics are Online Now
characters left:
Not a Chevy Question?

Related Cheverolet Topics:

  • Arm
  • ,
  • Gsi
  • ,
  • Nut
  • ,
  • Map
  • ,
  • Six
  • ,
  • Top
  • ,
  • Two
  • ,
  • Bolt
  • ,
  • Info
  • ,
  • Hood
Bookmark and Share

Question

need to take front fender off to paint

Submitted: 593 days and 6 hours ago.
Category: Chevy
Value: $9
Status: CLOSED
+
Read More

Optional Information

Optional Information:
2007 Chevrolet ZO-6

Already Tried:
we want instructions before we attempt to remove the fender.

Accepted Answer

Hello, and welcome to JA!! here is the instructions for front fender replacement!!

I hope this info was helpfull!!!

Object
View Full Image

Callout

Component Name

Preliminary Procedures

  1. Remove the front headlamp assembly.
  2. Remove the air inlet grille.

1

Fender Bolt (Qty: 10)

 

Tighten
2 N·m (18 lb in)

2

Fender Assembly

Tip
Transfer any brackets or harness that might be attached to the fender assembly.

 

Object
View Full Image


Callout

Component Name

Preliminary Procedures

    Caution: The high intensity discharge system produces high voltage and current. In order to reduce the risk of severe shocks and burns, the battery negative cable must be disconnected any time service work is being performed on or around the high intensity discharge system.

    Caution: The high intensity discharge system produces high voltage and current. To reduce the risk of severe shocks and burns:

    • Never open the high intensity discharge system ballast or the arc tube assembly starter.
    • Never probe between the high intensity discharge system ballast output connector and the arc tube assembly.

     

  1. Open the hood.
  2. Remove the six upper fender flange bolts from the side the headlamp is being serviced from.
  3. Raise and support the vehicle.
  4. Remove the front wheelhouse liner.
  5. Remove the front bumper fascia.
  6. Remove the three lower headlamp nuts from the front wheelhouse panel.
  7. Disconnect the headlamp electrical connectors from the headlamp.
  8. Lower the vehicle.
  9. Lift the front corner of the fender and raise the fender approximately two inches, enough to lift upward on the headlamp and release the studs from the wheelhouse panel in order to remove the headlamp from the vehicle.

1

 

Tighten
10 N·m (89 lb in)

2

Headlamp Nut

Tighten
2 N·m (18 lb in)

3

Headlamp Assembly

 

Front Wheelhouse Liner Replacement (Front Liner)
Object
View Full Image


Callout

Component Name

Preliminary Procedures

  1. Remove the appropriate front wheel and tire assembly.
  2. Remove the appropriate wheelhouse extension.

1

Front Wheelhouse (Front Liner) Liner Plastic Retainer (Qty: 7)

2

Front Wheelhouse (Front Liner) Liner

 

 

Picture
Expert: goodwrench9124
Pos. Feedback: 99.8 %
Accepts: 
Answered: 4/8/2008

ASE Certified Technician

Ase Master Certified, GM Master Certified Tech. Awarded GM Top performer,

Posted by goodwrench9124 592 days and 22 hours ago.

Answer

Air Inlet Grille Panel Replacement
Object
View Full Image


Callout

Component Name

 

1

Cap, Wiper Arm (Qty: 2)

2

Nut, Wiper Arm (Qty: 2)

Tighten
25 N·m (18 lb ft)

3

Wiper Arm, Wiper Arm Assembly

Important: Use the J 39637Wiper Arm Puller to remove the wiper arm from the wiper arm drive spindle.

4

Seal, Hood

5

Screw, Air Inlet Grille Panel (Qty: 2)

Tighten
3 N·m (27 lb in)

6

Panel Assembly, Air Inlet Grille Panel

 

Front Fender Replacement
Object
View Full Image


Callout

Component Name

Preliminary Procedures

  1. Remove the front headlamp assembly.
  2. Remove the air inlet grille.

1

Fender Bolt (Qty: 10)

 

Tighten
2 N·m (18 lb in)

2

Fender Assembly

Tip
Transfer any brackets or harness that might be attached to the fender assembly.

+
Read More

Related Chevy Questions

  • I am experiencing a rubbing noise on my front driver side wh...
  • 1995gmc k1500 heater not working swich only worked on high
  • Does anyone know what is the correct push rod lenght when re...
  • i have a 1994 astro van it will not stay running it starts r...
  • Why is bluetooth an option on a Malibu 1LT when you order it...
  • my car wont start it tries to to over but it doesnt the oil
  • I have a 2007 hd2500 with a diesel motor .The check engine
  • i have a 2000 k2500 with a 5.7 litre vortec. no fire, no sta...



Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.
Question List | Become an Expert | Terms of Service | Security & Privacy | About Us
© 2003-2009 JustAnswer Corp.