How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask scottyfum Your Own Question
scottyfum
scottyfum, Pontiac Technician
Category: Pontiac
Satisfied Customers: 118
Experience:  General Motors factory trained technician with 12 years experience, Grand Master Tech.,ASEP trained
9473634
Type Your Pontiac Question Here...
scottyfum is online now
A new question is answered every 9 seconds

installing wiper motor bracket 2002 grand prix

Resolved Question:

installing wiper motor bracket 2002 grand prix
Submitted: 7 years ago.
Category: Pontiac
Expert:  scottyfum replied 7 years ago.

here you go.

 

Windshield Wiper Transmission Replacement

Removal Procedure

  1. Remove the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement in Body Front End.
  2. Remove the wiper drive system module. Refer to Windshield Wiper System Module Replacement .
    Object Number: 334247  Size: SH
    Click here for detailed picture of above image.
  3. Remove the wiper transmission caps.
  4. Remove the wiper transmission screws.
  5. Remove the wiper transmission from the wiper drive system module tube frame.

Installation Procedure


    Object Number: 334247  Size: SH
    Click here for detailed picture of above image.
  1. position the wiper transmission to the wiper drive system module tube frame.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install wiper transmission screws.

    Tighten
    Tighten the screws to 9 N·m (80 lb in).

  3. Install the wiper transmission caps.
  4. Install the wiper drive system module. Refer to Windshield Wiper System Module Replacement .
  5. Install the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement in Body Front End.
  6. Operate the windshield wipers and inspect for proper operation.
scottyfum and 5 other Pontiac Specialists are ready to help you
Customer: replied 7 years ago.
what about setting the tab so it is in correct timing?
Expert:  scottyfum replied 7 years ago.

Here you go. Take your time and follow the instructions and you will not have a problem.

 

Wiper Motor Crank Arm Replacement

Tools Required

J 39232 Wiper Transmission Separator
J 39529 Wiper Transmission Installer

Removal Procedure

  1. Remove the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement in Body Front End.
  2. Remove the wiper motor water deflector. Refer to Windshield Wiper and Windshield Washer Control Module Water Deflector Replacement .
    Object Number: 306506  Size: SH
    Click here for detailed picture of above image.
  3. Using the J 39232 , disconnect the wiper transmission from the wiper motor crank arm.
    Object Number: 334250  Size: SH
    Click here for detailed picture of above image.
  4. Remove the wiper motor crank arm cover.
  5. Remove the wiper motor crank arm screw.
  6. Remove the wiper motor crank arm from the wiper motor.

Installation Procedure

  1. Before installing the wiper motor crank arm, the wiper motor must be in the inner wipe position of the delay mode.
    Object Number: 512040  Size: SH
    Click here for detailed picture of above image.
  2. Position the wiper motor crank arm onto the wiper motor.
  3. Measure the gap between wiper motor crank arm and the bracket tab. If the gap is not 4-8 mm (0.157-0.314 in), remove the wiper motor crank arm and repeat installation.

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 334250  Size: SH
    Click here for detailed picture of above image.
  4. Install the wiper motor crank arm screw .

    Tighten
    Tighten the screw to 16 N·m (12 lb ft).

  5. Install the wiper motor crank arm cover.
    Object Number: 306515  Size: SH
    Click here for detailed picture of above image.
  6. Using the J 39529 , install the wiper transmission to the wiper motor crank arm.
  7. Install the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement in Body Front End.
  8. Install the wiper motor water deflector. Refer to Windshield Wiper and Windshield Washer Control Module Water Deflector Replacement .
  9. Operate the windshield wipers and inspect for proper operation.
scottyfum and 5 other Pontiac Specialists are ready to help you