How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask FIXITMAN Your Own Question
FIXITMAN
FIXITMAN, MasterTechnician
Category: Nissan
Satisfied Customers: 17144
Experience:  ASE Master Certified, AA Degree Auto/Diesel Tech
1627031
Type Your Nissan Question Here...
FIXITMAN is online now
A new question is answered every 9 seconds

I M HAVING ISSUE WITH NISSAN XTERRA 2006 ITS DRAGGING AFTER

Customer Question

I M HAVING ISSUE WITH NISSAN XTERRA 2006
ITS DRAGGING AFTER CHANGING TRANSMISSION OIL, GOT CODE P0057, P0181, SLIP LIGHT ON
Submitted: 9 months ago.
Category: Nissan
Expert:  FIXITMAN replied 9 months ago.

Hello, my name is ***** ***** you for the question. Did this start right after changing the fluid? Was the transmission flushed? What kind of fluid was used?

Customer: replied 9 months ago.
a day after
Customer: replied 9 months ago.
i used Nissan matic J
Expert:  FIXITMAN replied 9 months ago.

Was the transmission pan removed?

Customer: replied 9 months ago.
i did not flush the system
Customer: replied 9 months ago.
i removed the transmission pan
Customer: replied 9 months ago.
i was advicsed to change the fuel pump, which i did
Customer: replied 9 months ago.
also the spark plugs
Customer: replied 9 months ago.
the car keeps on dragging, even while pressing accelerator pedal
Expert:  FIXITMAN replied 9 months ago.

The codes you are getting do not have anything to do with the transmission. The codes are for the fuel pump temperature sensor and the oxygen sensors. Were these replaced?

Customer: replied 9 months ago.
i have ordered for the oxygen sensor, don't know where to locate the fuel temp sensor
Customer: replied 9 months ago.
are my replacing all the oxygen sensons, cos the code states HO2 2/2
Expert:  FIXITMAN replied 9 months ago.

Your code is for the heater circuit on the oxygen sensor. Did you disconnect any of the sensors when servicing the transmission?

Customer: replied 9 months ago.
No
Expert:  FIXITMAN replied 9 months ago.

You can either change the sensors or check the voltage at the sensor for the heater circuits

Customer: replied 9 months ago.
i will change the sensor (1)
Customer: replied 9 months ago.
how do i check the voltage? from the scanner?
Expert:  FIXITMAN replied 9 months ago.

I would start by checking fuse number 54 in the fuse box under the hood.

Customer: replied 9 months ago.
ok
Customer: replied 9 months ago.
any picture
Customer: replied 9 months ago.
maybe you can send me the wiring diagram showing all the fuses
Expert:  FIXITMAN replied 9 months ago.

My data base is not working right now. I will see if I have one when it is back up.

Customer: replied 9 months ago.
thanks
Customer: replied 9 months ago.
there is also P0158 code
Customer: replied 9 months ago.
slip light is still on after cleaning all the wheel sensors
Customer: replied 9 months ago.
hello
Expert:  FIXITMAN replied 9 months ago.

Did this code come up with all of the other codes?

Customer: replied 9 months ago.
Expert:  FIXITMAN replied 9 months ago.

Thank you. I don't have any diagrams available for your vehicle. Did you check the fuses that I mentioned? The fuse box cover should be marked with the numbers.

Customer: replied 9 months ago.
I checked bank 1 sensor 2 (driver side) and discovered the cable on the sensor is damaged. fixed that already. for now i have erased all codes and hoping that it won't come back
Customer: replied 9 months ago.
2 major issues now before i go into other things are
Customer: replied 9 months ago.
though there is changes in the movement but the sharp take off known for xterra is not yet there. acceleration is a bit sluggish. then slip light is still on despite cleaning all the wheel sensors (front & rear)
Customer: replied 9 months ago.
there is no number on the fuse
Customer: replied 9 months ago.
the fuse is for what component
Customer: replied 9 months ago.
i just re-park the car now and i discovered the code P0181 - fuel temp sensor is back
Expert:  FIXITMAN replied 9 months ago.

The fuel sensor may be the part that you need to replace. This is located on the top of the fuel housing. Did your fuel pump come with a new fuel temperature sensor.

Customer: replied 9 months ago.
i m sure, but see attached the pictures of the fuel pump i installed
Customer: replied 9 months ago.
Please i need the picture of the fuel temp sensor
Expert:  FIXITMAN replied 9 months ago.

That fuel pump should have a new sensor in it already.

Customer: replied 9 months ago.
By replacing the fuel pump (complete unit) and the H02 sensor 2/2, the check light is already off?The issue i m still having as i have been reintering (other ones above are just add ons which where detected when i scanned the system) are:1. the vehicle drags after driving for a while as if its moving by force and appears heavy with the steering wheel a bit hard to drive.2. slip light remain on despite cleaning the wheel sensors. I discovered while cleaning the sensors, it was only the passenger wheel sensor that accumulated a lot of dirt (though cleaned now).please advise as enumerated above.Thanks
Expert:  FIXITMAN replied 9 months ago.

The slip light coming on is an indication of the traction control system turning on which will cause a power loss. You need to scan the traction control module to see what codes are coming up when the light comes on. Does your scan tool have this capability or is it just a generic scan tool?

Customer: replied 8 months ago.
good morning,
sorry for my late response. I have been busy lately
I will have the traction system check and revert to you asap
thanks
Expert:  FIXITMAN replied 8 months ago.

Sounds good. Thank you.

Related Nissan Questions