How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Alex Olsen Your Own Question
Alex Olsen
Alex Olsen,
Category: Medium and Heavy Trucks
Satisfied Customers: 93
Experience:  Lead technican at Astleford international trucks
96118949
Type Your Medium and Heavy Trucks Question Here...
Alex Olsen is online now
A new question is answered every 9 seconds

How does this work? 95 international 4700 1htscabm15h598032,

Customer Question

How does this work?
JA: What is the complete model and serial number of your machine?
Customer: 95 international 4700 1htscabm15h598032
JA: Are you fixing this yourself? What have you tried so far?
Customer: myself I have two codes coming up and a no start issue
JA: Anything else you want the equipment mechanic to know before I connect you?
Customer: no
Submitted: 1 month ago.
Category: Medium and Heavy Trucks
Customer: replied 1 month ago.
the codes are 29 and 224
Expert:  Alex Olsen replied 1 month ago.

hi im alex, do yo have a scanner you are getting the codes or are they blink codes?

Customer: replied 1 month ago.
cannot get flash codes but did get scanner codes of 29 and 244 they are active and I cannot clear them truck will not start
Expert:  Alex Olsen replied 1 month ago.

ok thanks, ***** ***** recheck the last 8 digits of your VIN comes up invalid when i try and pull it up

Customer: replied 1 month ago.
sh598033 or 32 vin sticker messed up
Expert:  Alex Olsen replied 1 month ago.

ok thanks

Expert:  Alex Olsen replied 1 month ago.

244 is a engine data line code, will it crank and not start or not even crank

Customer: replied 1 month ago.
crank and no start. ether will make it run but will no stay running
Expert:  Alex Olsen replied 1 month ago.

do you show oil pressure on the gauge when cranking

Customer: replied 1 month ago.
just replaced oil pump due to lack of psi originally had codes to back it up too
Expert:  Alex Olsen replied 1 month ago.

you replaced the HP pump or base engine oil pump?

Customer: replied 1 month ago.
hpop
Expert:  Alex Olsen replied 1 month ago.

does your scanner read data? what are you getiting for ICP if it does?

Customer: replied 1 month ago.
cannot read icp scanner very limited
Expert:  Alex Olsen replied 1 month ago.

ok this will be tough then

Expert:  Alex Olsen replied 1 month ago.

does it sound like the injectors are cycling when you crank?

Customer: replied 1 month ago.
no and I need to do injector buzz test
Expert:  Alex Olsen replied 1 month ago.

ok , does the glowplug relay cycle?

Customer: replied 1 month ago.
Expert:  Alex Olsen replied 1 month ago.

ok we know the ecm has power then, does it smoke at all?

Customer: replied 1 month ago.
not like it should be
Expert:  Alex Olsen replied 1 month ago.

ok i would check engine fuel pressure at the filter housing

Customer: replied 1 month ago.
did even applied air pressure to system
Expert:  Alex Olsen replied 1 month ago.

ok so you have good fuel pressure, if you crank on it for a minuet or so do you get any other engine codes

Customer: replied 1 month ago.
190
Expert:  Alex Olsen replied 1 month ago.

what code did you have before that you replaced the HP pump 333?

Customer: replied 1 month ago.
something close to that
Expert:  Alex Olsen replied 1 month ago.

ok well based on what you have told me the fuel pressure is good and you have no ICP codes so we have to assume that you are buliding ICP since we cant read it, looks like this is a tow truck those usually have high idle time which is terrible for the injectors so i would say injectors need to be buzz tested and more than likely they are warn out

Expert:  Alex Olsen replied 1 month ago.

any idea how many miles are on the injectors?

Customer: replied 1 month ago.
same id imagine given the customer. I'm thinkin wiring and modules just cannot prove it
Expert:  Alex Olsen replied 1 month ago.

no its tough to sell injectors to customers when you have no real hard proof, but a buzz test is a good induction if you cant hear the injectors

Expert:  Alex Olsen replied 1 month ago.

very limited with a scanner as well which makes it tough

Expert:  Alex Olsen replied 1 month ago.

i am an independent contractor i receive no compensation until you rate me, all follow up questions after rating will be free of charge. Thanks

Expert:  Alex Olsen replied 1 month ago.

Please rate my service when you get a chance, i will continue to help after you rate me, i have helped customers up to 25days after first contact so rate with confidence, thank you

Expert:  Alex Olsen replied 1 month ago.

Please rate my service when you get a chance, i will continue to help after you rate me, i have helped customers up to 25days after first contact so rate with confidence, thank you

Related Medium and Heavy Trucks Questions