How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Daniel Wilson Your Own Question
Daniel Wilson
Daniel Wilson,
Category: Medium and Heavy Trucks
Satisfied Customers: 4679
Experience:  Owner at DJ Wilson
65405794
Type Your Medium and Heavy Trucks Question Here...
Daniel Wilson is online now
A new question is answered every 9 seconds

I am ***** ***** and i have a case cx330, that started

Customer Question

hi i am ***** ***** and i have a case cx330, that started running poorly and shows electrical problem, and now will not even try to start
JA: Thanks. Can you give me any more details about your issue?
Customer: machine ran fine in december, been sitting since, started it and it was running rough, so i replaced the fuel filter. today smoked all day kept loosing power and showing electrical problem. shut the machine off and now you turn the key and everything is on, fuel pump running but will not even turn over
JA: OK got it. Last thing — Technicians generally expect a deposit of about $54 to help with your type of question (you only pay if satisfied). Now I'm going to take you to a page to place a secure deposit with JustAnswer. Don't worry, this chat is saved. After that, we will finish helping you.
Submitted: 1 year ago.
Category: Medium and Heavy Trucks
Expert:  cat_engines_only replied 1 year ago.

I am sorry but, I am not familiar with this machine. I will OPT-OUT so other experts can pickup your question.

Expert:  Daniel Wilson replied 1 year ago.

Hi my name is***** the accessories are still on in the cab then check for any fault or warning indicators through the monitor panel and let me know what they are. Test for power on both sides of your fuses with the key on and replace any with power only on one side. Swap relays one at a time with a known good one for test purposes. Check continuity of the safety lever switch on the LH console in both the open and closed position. Also test for power at the starter solenoid S terminal with the key in the crank position. If there is power there and good batteries and connections, replace the faulty solenoid or starter. If there is no power there isolate the circuit between the Key switch and solenoid. Let me know

Customer: replied 1 year ago.
It's showing fault codes
E0276
E0277
E0153
Expert:  Daniel Wilson replied 1 year ago.

E 0153 Intake air temp sensor high

The other two my list skips over but are in the same range with the fuel system codes

E 0261 Fuel temp sensor pump over-heat
E 0264 VP44 fuel temp sensor
E 0278 Lift pump relay
E 0283 ESS/Crankshaft position sensor high
E 0284 ESS/Crankshaft position sensor low
E 0319 EECM
E 0352 Sensor voltage supply
E 0361 VP44 fuel system high current
E 0362 VP44 fuel system value open
E 0363 VP44 fuel system feed back error
E 0364 VP44 fuel system com error
E 0365 VP44 fuel system low

E 0366 VP44 fuel system measurement error
E 0367 VP44 fuel system IAT error
E 0368 VP44 fuel system timing error
E 0369 VP44 fuel system sync error
E 0372 VP44 fuel system idle validation error
E 0373 VP44 fuel system FSO high
E 0374 VP44 fuel system shutoff error
E 0376 VP44 fuel system mismatch error
E 0377 Fuel pump power shutoff relay

Expert:  Daniel Wilson replied 1 year ago.

Double check the codes but this is what is in my list in that range.

Related Medium and Heavy Trucks Questions