How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Chris Your Own Question
Chris, Shop Foreman
Category: Jeep
Satisfied Customers: 12511
Experience:  Jeep Certified Master Tech
Type Your Jeep Question Here...
Chris is online now
A new question is answered every 9 seconds

How do you replace a heater A/C blower motor, where is it located

Resolved Question:

How do you replace a heater A/C blower motor, where is it located and how do you get to it
Submitted: 6 years ago.
Category: Jeep
Expert:  Chris replied 6 years ago.

Hello and welcome to just answer Jeep. The blower motor on your Commander is located at the lower right side of the dash. Here is the information regarding the blower motor for you. Hope this helps, and let me know if you need more assistance with this,





The blower motor (1) is a 12-volt, direct current (DC) motor mounted within a plastic housing with an integral wire lead and connector (2) and squirrel cage-type blower wheel (3) that is secured to the blower motor shaft (4). The blower motor wheel is located in the HVAC air inlet housing which is mounted to the passenger side end of the HVAC housing.

The blower motor can be accessed for service from underneath the instrument panel.












NOTE: LHD model shown. RHD model similar.
1.Disconnect and isolate the negative battery cable.
2.Remove the instrument panel silencer from the passenger side of the instrument panel.
3.Remove the glove box from the instrument panel (Refer to 23 - Body/Instrument Panel/GLOVE BOX, Instrument Panel - Removal) .
4.Disconnect the blower motor wire harness connector (1) from the blower motor power module or resistor (2), depending on how equipped.
5.Remove the three screws (3) that secure the blower motor (4) to the HVAC housing (5).
6.Remove the blower motor from the HVAC housing.





1.Separate the glove box damper rod (1) from the clove box by sliding the rod towards the rear of the vehicle to release it from the bin.

2.Open the glove box and carefully use fingers to press down glove box open stops at the top of the bin, downward to allow the glove box to rotate toward the carpet.
3.Rotate the box down and release the door hinges (2) at the bottom and remove the glove box.

Chris, Shop Foreman
Category: Jeep
Satisfied Customers: 12511
Experience: Jeep Certified Master Tech
Chris and 6 other Jeep Specialists are ready to help you

JustAnswer in the News:

Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.

What Customers are Saying:

  • Thank you so much for your answer. My initial estimate was $325; I got it done for $100 - part and labor. Lynn B. Ormond Beach, FL
< Previous | Next >
  • Thank you so much for your answer. My initial estimate was $325; I got it done for $100 - part and labor. Lynn B. Ormond Beach, FL
  • I was skeptical at first but thought I'd give it a try. I was pleasantly surprised. Your site actually is a quality service that I would recommend to others in a heartbeat. Stan Sayre, PA
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
  • This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!! Alex Los Angeles, CA
  • Thank you for all your help. It is nice to know that this service is here for people like myself, who need answers fast and are not sure who to consult. GP Hesperia, CA
  • I couldn't be more satisfied! This is the site I will always come to when I need a second opinion. Justin Kernersville, NC
  • Just let me say that this encounter has been entirely professional and most helpful. I liked that I could ask additional questions and get answered in a very short turn around. Esther Woodstock, NY

Meet The Experts:

  • Chris


    Shop Foreman

    Satisfied Customers:

    Jeep Certified Master Tech
< Last | Next >
  • Chris's Avatar


    Shop Foreman

    Satisfied Customers:

    Jeep Certified Master Tech
  • Mark's Avatar


    22 Year Factory trained technician

    Satisfied Customers:

    Jeep factory training........25 years in the industry.
  • Dave's Avatar


    Jeep Master Tech

    Satisfied Customers:

    Chrysler Triple Master, ASE master Tech AA degree in Auto.
  • moparfl's Avatar


    ASE Certified Technician

    Satisfied Customers:

    ASE Master Tech Chrysler Dodge Jeep Master Tech
  • Tim Mohr's Avatar

    Tim Mohr


    Satisfied Customers:

  • Ron Z.'s Avatar

    Ron Z.

    - Jeep Tech -

    Satisfied Customers:

    18+yrs experience. State Inspector & Jeep Diagnostics/Repair
  • jeepmopar76's Avatar


    Jeep/Chrysler Triple Master Tech

    Satisfied Customers:

    32yr ASE Master Tech, 9yr Chrysler Master Tech, 19 yr Jeep Dealership service including AMC/Eagle