How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Sean Your Own Question
Sean
Sean, HVAC Technician
Category: HVAC
Satisfied Customers: 184
Experience:  Owner HVAC company
64612473
Type Your HVAC Question Here...
Sean is online now
A new question is answered every 9 seconds

I have a m1 blue and m2 red and I need to plug it into

Customer Question

I have a m1 blue and m2 red and I need to plug it into universal board and the slots that are available are hum, Ind, cont, and eac
Submitted: 7 months ago.
Category: HVAC
Expert:  BillyHvac replied 7 months ago.

Hello,

My name is ***** ***** I will do my best to assist you. I am looking over your question now and will respond shortly.

Expert:  BillyHvac replied 7 months ago.

M1 and M2 are unused blower wires. They just need a dummy terminal to put on. It can M1 and M2...it could be terminals labeled PARK...

Do you have park terminals? or what board do you have?

Customer: replied 7 months ago.
No park terminal I have a hum, cont, Ind, and eac. I have a universal arcoaire board made by Honeywell
Customer: replied 7 months ago.
Posted by JustAnswer at customer's request) Hello. I would like to request the following Expert Service(s) from you: Live Phone Call. Let me know if you need more information, or send me the service offer(s) so we can proceed.
Customer: replied 7 months ago.
I still need more information on this please ASAP
Expert:  BillyHvac replied 7 months ago.

hum = humidifier

cont = continuous fan

IND = inducer

EAC = electric air cleaner

Give me model number of the board and I can tell you where they go...but these are extra wires and can just be taped off and not put on board at all.

Expert:  BillyHvac replied 7 months ago.

M1

M2

M2

Park

Unused

all of those are dummy terminals just for a place to put unused wires.

Customer: replied 7 months ago.
The model number is *****
Expert:  BillyHvac replied 7 months ago.

What is number of board you used?

Expert:  BillyHvac replied 7 months ago.

Honeywell st9120?

Customer: replied 7 months ago.
No it's st9160
Customer: replied 7 months ago.
I'm using a st9120u
Expert:  BillyHvac replied 7 months ago.

ok...so you should have terminals labeled "unused motor wires"

see here

Customer: replied 7 months ago.
I'm using a st9120u board
Expert:  BillyHvac replied 7 months ago.

Yes...see previous response with this link HERE

Customer: replied 7 months ago.
I need to know where m1 blue and m2 red go on st9120u board
Customer: replied 7 months ago.
The old board is a st9160b1084
Expert:  BillyHvac replied 7 months ago.

I just showed you.

Dont you have the unused terminals I showed in picture?

Customer: replied 7 months ago.
No this one doesn't have the unusual terminals
Expert:  BillyHvac replied 7 months ago.

Is this your board shown here

Customer: replied 7 months ago.
M1 and m2 off old board converts to what on a st9120u board.
Expert:  BillyHvac replied 7 months ago.

They go to terminals "unused"..just like the manual says..click the blue word below

CLICK HERE

If you still do not understand I want you to take a pic of your board..or write down for me every terminal available

Customer: replied 7 months ago.
I need to know where m1 and m2 off a st9160b1084 goes on a st9120u board
Expert:  BillyHvac replied 7 months ago.

Are you getting my replies?

I sent 2 pictures direct from the st9120u manual.

Just tell me ALL the terminals you have open on the board...

BUT you dont even need them...M1 and M2 are leftover wires...They only plug onto terminals for somewhere to keep them.

You can leave M1 and M2 totally unhooked from board and taped off and it is the same thing...these wires are not used.

Customer: replied 7 months ago.
Now with the new board hooked up the fan now works but the burner's are not trying to fire
Expert:  BillyHvac replied 7 months ago.

did you cross the wires to new terminals as described in the chart I sent?

Customer: replied 7 months ago.
Which wires
Customer: replied 7 months ago.
Can you please send me one now I really need my furnace I have lil one's
Customer: replied 7 months ago.
What does it mean when the green light is flashing on the board and it's still not firing up but the blower kicks in?
Expert:  Sean replied 7 months ago.

Are you still needing assistance?

Customer: replied 7 months ago.
please
Customer: replied 7 months ago.
It's not calling for fire
Customer: replied 7 months ago.
Posted by JustAnswer at customer's request) Hello. I would like to request the following Expert Service(s) from you: Live Phone Call. Let me know if you need more information, or send me the service offer(s) so we can proceed.
Customer: replied 7 months ago.
My board isn't sending a signal to call for fire
Customer: replied 7 months ago.
Can I get some help here please
Expert:  Sean replied 7 months ago.
I opted out last night because I was available, I can help for aittle bit now if your on?