How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask HondaPlatinum Your Own Question

HondaPlatinum
HondaPlatinum, A Technician
Category: Honda
Satisfied Customers: 25346
Experience:  13 year honda platinum level
3827149
Type Your Honda Question Here...
HondaPlatinum is online now
A new question is answered every 9 seconds

how do u bleed the abs module on a crv 2003

Resolved Question:

how do u bleed the abs module on a crv 2003
Submitted: 4 years ago.
Category: Honda
Expert:  HondaPlatinum replied 4 years ago.
Theres is a special bleeder for this from Honda since its under alot of pressure but you can use a rubber hose tightley on the bleeder valve
-with modulator bleed valve open and a pipe to safely channel fluid to a container
-bridge the pump motor relay female terminals 1 & 2, until clear bubble free air is seen
-ensure fluid is topped up continuously so as not to run pump dry
-individually bleed each wheel in sequence: RHR, LHF, LHR, RHF.
-top resevoir to back up to maximum
Customer: replied 4 years ago.
wich reservoir master cylinder or abs resevoir
if abs where is the reservoir
Expert:  HondaPlatinum replied 4 years ago.
Its off abs modulator below the reservoire let me see if I can post a picture.
Customer: replied 4 years ago.
thanks
Expert:  HondaPlatinum replied 4 years ago.
Having trouble locating the picture but it should be right next to the abs resevoire.
Customer: replied 4 years ago.
i was browsing while waiting , the information a found is that my abs module is a teves mark 20 and that u need a dbrIII scan tool in order to lauch the abs module into a bleeding sequence in order to remove air trap in it.
Expert:  HondaPlatinum replied 4 years ago.
Yes that is true the procedure is for the old style abs what was the actual problem you were having .
Customer: replied 4 years ago.
i change my brake pad and rotor and to make a nice job i bleeded all my brake fluid and i believe i let the master cylinder tank go too low and air got into the system. i kept on bleeding a amount of 1 quart of oil. my car brake just fine on a very short brake pedal stroke. but if a keep applying pressure on the brake pedal the pedal will go slowly to the floor. whith the engine not running i can not get the pedal to further then 1 inch. that why i think that air is trap into the abs unit since is not working when the engine is off
Expert:  HondaPlatinum replied 4 years ago.
Ok that is doubtful have you bleed each wheel several times?
Customer: replied 4 years ago.
yes
Expert:  HondaPlatinum replied 4 years ago.
Ok I would bleed the lines at the master and all the other wheels again its doubtful air got into the abs system good chance thge master cylinder is airbound.
HondaPlatinum, A Technician
Category: Honda
Satisfied Customers: 25346
Experience: 13 year honda platinum level
HondaPlatinum and other Honda Specialists are ready to help you

JustAnswer in the News:

 
 
 
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
 
 
 

What Customers are Saying:

 
 
 
  • Thank you very much for saving my daughter and her family a lot of money on her Honda. You are definitely on my list for future help. Thanks, again. Fred USA
< Last | Next >
  • Thank you very much for saving my daughter and her family a lot of money on her Honda. You are definitely on my list for future help. Thanks, again. Fred USA
  • I just heard from my mechanic. You were right...a $45.00 job. THANK YOU!! Your response was received in less than 10 minutes!! Linda B. USA
  • Your answers were clear and the diagrams were perfect. Dealer wanted $87 for an hour of labor and even I did it in 15 minutes. Ed USA
  • HONDA PLATINUM was great. I really appreciate his help. I was ready to trade my new Honda until he told me to wait until I got 3,000 miles on it and my gas mileage would get much better. Summer USA
  • I took the Power Steering O-Ring service bulletin linked from JustAnswer to my Acura dealer, and not only did they no-charge the o-ring, they also replaced the power steering pump at no cost. Gary R Stevenson Ranch, CA
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
  • This expert is wonderful. They truly know what they are talking about, and they actually care about you. They really helped put my nerves at ease. Thank you so much!!!! Alex Los Angeles, CA
 
 
 

Meet The Experts:

 
 
 
  • Kyle N.

    Honda Master Tech

    Satisfied Customers:

    3627
    Honda Dealer Tech, ASE Master Auto Tech
< Last | Next >
  • http://ww2.justanswer.com/uploads/hondatech/2010-05-03_025935_resized_work_pic.jpg Kyle N.'s Avatar

    Kyle N.

    Honda Master Tech

    Satisfied Customers:

    3627
    Honda Dealer Tech, ASE Master Auto Tech
  • http://ww2.justanswer.com/uploads/hondacb77/2008-10-27_165606_me3.jpg John G.'s Avatar

    John G.

    Honda Technician

    Satisfied Customers:

    2643
    Dealership tech since 1982. ASE and Honda Master Technician.
  • http://ww2.justanswer.com/uploads/MU/muddyford/2012-6-13_1204_1.64x64.png Chris (aka-Moose)'s Avatar

    Chris (aka-Moose)

    Technician

    Satisfied Customers:

    204
    16 years of experience
  • http://ww2.justanswer.com/uploads/FO/fordguy4u/2011-12-17_222940_HPIM1257.64x64.JPG Ron's Avatar

    Ron

    ASE Certified Technician

    Satisfied Customers:

    175
    ASE Certified Tech 34 years.
  • http://ww2.justanswer.com/uploads/EU/eurotec/2012-6-11_13153_mpjaphoto.64x64.JPG Marty's Avatar

    Marty

    Bosch Master Tech

    Satisfied Customers:

    113
    Bosch Certified Master Technician
  • http://ww2.justanswer.com/uploads/AM/amedee/2013-10-24_23656_Amedee1.64x64.jpg Amedee's Avatar

    Amedee

    ASE Master Technician

    Satisfied Customers:

    1112
    ASE Master Technician advanced level specialist. Wisconsin certified emissions state inspector
  • http://ww2.justanswer.com/uploads/TH/thebesthonda/2011-1-15_04510_Photo022009005.64x64.jpg thebesthonda's Avatar

    thebesthonda

    ASE MasterTechnician

    Satisfied Customers:

    2299
    26 years experience