How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask Scott Your Own Question

Scott
Scott, MIT Graduate
Category: Homework
Satisfied Customers: 3040
Experience:  MIT Graduate (Math, Programming, Science, and Music)
3546829
Type Your Homework Question Here...
Scott is online now
A new question is answered every 9 seconds

I am looking for the answers to this test that was posted 2

Customer Question

I am looking for the answers to this test that was posted 2 years ago. exam number 006036RR electrical blue print read
JA: The Tutor can help you get an A on your homework or ace your next test. Tell me more about what you need help with so we can help you best.
Customer: exam number 006036RR penn foster test. electrical blue print read
JA: Is there anything else the Tutor should be aware of?
Customer: no
Submitted: 3 months ago.
Category: Homework
Customer: replied 3 months ago.
1.How many receptacles are connected to circuit 24 from panel
RPB in the manufacturing facility? Use the series of plates
supplied with this study unit.
A. 1 C. 4
B. 3 D. 8
2. What is the meaning of the symbol S3?
A. Three single-pole switches
B. One three-way switch
C. A triple-pole switch
D. A single switch mounted at 3-0��
3. For the manufacturing facility, what conductors connect panel
PP2 to the main power supply?Use the series of plates supplied
with this study unit.
A. 8 conductors #500,000 circular mil size and 2-#1/0 size
ground conductors
B. 4-#4/0 size conductors and 1-#4 size ground conductor
C. 8 conductors #500,000 circular mil size and 1-#1/0 size
ground conductor
D. 3 conductors #600,000 circular mil size and 1-#2 size
ground conductor
What circuit provides power for the water heater located in the mechanical room of the
manufacturing facility?
A. RPB-30 C. LPB-25
B. RPB-32 D. RPB-21
5. What is the meaning of the symbol shown in Figure A1?
A. Five wires for circuit #7
B. Seven wires for circuit #5
C. Circuits #5 and #7 connected together
D. Circuits #5 and #7 home run to panel
6. In Figure 2A of your study unit, what is the distance between the two conductors
identified as phases B and A where they exit Bay 2?
A. 2-0�� C. 3-6��
B. 2-6�� D. 12-0��
7. In Figure 12 of your study unit, the contact SA1 in the electric furnace control closes
A. immediately when the thermostat calls for heat.
B. when the load limit switch (LS1) operates.
C. when the heater coil sequencer (HTRSEQ1) operates.
D. whenever the 24-V transformer is energized.
8. What voltage is supplied to the panel RPB in the manufacturing facility? Use the series
of plates supplied with this study unit.
A. 480/277 V C. 240/120 V
B. 208/120 V D. 230 V
9. What is the voltage supplied to the light fixtures in the communication room of the
manufacturing facility? Use the series of plates supplied with this study unit.
A. 120 V C. 277 V
B. 208 V D. 480 V
10. In the manufacturing facility, what does transformer T1 do? Use the series of plates
supplied with this study unit.
A. Provides panel LPB with voltage stepped down from 480 V to 230 V
B. Provides panel DPB with voltage stepped up from 480 V to 120 V
C. Provides panel DPB with voltage stepped down from 480 V to 208/120 V
D. Provides panel LPB with voltage stepped down from 480 V to 208/120 V
FIGURE A1—Use this figure
to answer Question 5.
11. Which one of the following light fixtures is one of the types installed in the men’s
locker areas? Use the series of plates supplied with this study unit.
A. Lithonia 2SP-G-3-32-A12-277-GEBIO
B. Lithonia LGF2/18DTT-TRW-T73-277-GEB-TR
C. Lithonia 2SP-G-2-32-A12-277-GEBIO
D. Lithonia 2SP-G-2U31-A12-277-GEBIO
12. Which statement is true for the process-control relay ladder diagram shown in
Figure A2?
A. The pressure switch, temperature switch, and push button must be closed for the
motor to start.
B. Only the temperature switch has to close for the motor to start.
C. With the pressure switch closed and the push button released, the motor will start.
D. With the temperature switch closed, the motor will start once the push button is
pressed.
13. To read and understand electrical blueprints, what do you need to know?
A. The meaning of electric symbols
B. How buildings are constructed
C. The fundamentals of electrical engineering
D. How to sketch a plan view
14. How many two-pole 30-A breakers are installed in panel PP1? Use the series of plates
supplied with this study unit.
A. Two C. Eight
B. Four D. Nine
15. In the motor control circuit of Figure 11 in your study unit, the operation of any one of
the overload relays has which of the following effects?
A. The motor only runs on two phases.
B. The auxiliary contact M closes.
C. The motor operates normally.
D. The motor stops.
16. What is the meaning of the symbol shown in Figure A3?
A. Motor control
B. Light fixture
C. Solenoid
D. Fire alarm system
17. What does the symbol shown in Figure A4 stand for?
A. A duplex receptacle
B. A ground fault receptacle
C. A light fixture
D. Floor-mounted receptacle
18. How many phase conductors are installed between the
switch and the light fixture shown in Figure A5?
A. Two C. Four
B. Three D. Five
19. The third-angle projection of a structure shows
A. the front view only. C. top, front, and side views.
B. either a front, top, or side view. D. the top view only.
20. How many light circuits are shown in the basement area of the manufacturing facility?
Use the series of plates supplied with this study unit.
A. Two C. Four
B. Three D. Five
Customer: replied 3 months ago.
See attached pictures corresponding with questions
Expert:  akch2002 replied 3 months ago.

I will reply these questions. Kindly inform when these are due. Also inform list of all the questions along with fig. etc.

Customer: replied 3 months ago.
Due 9/9/16- I did list questions above and attached figures as well.
Expert:  akch2002 replied 3 months ago.

q1,2 and 3 are missing.

what about series of plates as mentioned in q10.

Customer: replied 3 months ago.
See below for 1-3 and see attached figures1.How many receptacles are connected to circuit 24 from panel
RPB in the manufacturing facility? Use the series of plates
supplied with this study unit.
A. 1 C. 4
B. 3 D. 8
2. What is the meaning of the symbol S3?
A. Three single-pole switches
B. One three-way switch
C. A triple-pole switch
D. A single switch mounted at 3-0��
3. For the manufacturing facility, what conductors connect panel
PP2 to the main power supply?Use the series of plates supplied
with this study unit.
A. 8 conductors #500,000 circular mil size and 2-#1/0 size
ground conductors
B. 4-#4/0 size conductors and 1-#4 size ground conductor
C. 8 conductors #500,000 circular mil size and 1-#1/0 size
ground conductor
D. 3 conductors #600,000 circular mil size and 1-#2 size
ground conductor
Expert:  akch2002 replied 3 months ago.

Thanks.I have got the questions and will work tomorrow on these questions.

Expert:  akch2002 replied 3 months ago.

Sorry; I will prefer to opt out as I am not sure about some of the questions.