Login|Contact Us
Question and Answer

Heavy Equipment

Ask a Heavy Equipment Question, Get an Answer ASAP!

  • Ask A Question
  • Browse Answers
  • Meet The Experts
  • How JustAnswer Works

What is the safe operating temperature range for a Hino h07c engine

 
wayne's Avatar
  • Answered by:wayne
  • Journeyman
  • Positive Feedback: 96.0 %
  • Accepted Answers: 2941
Verified Expert
in Heavy Equipment

Recent Feedback

Positive
yes this does answer my question. The pistons were in backwards.thank you for...
Positive
It sounds logical but haven' t had time to go through the whole procedure, I...
Positive
Thank you very much Wayne!! Once I gave you the information pertinent to the...
Positive
thank u for an easy to understand answer.
Positive
good work thanks
Positive
Thanks
Positive
Thanks
Positive
quick response and easy to understand thanks
Positive
got me out of a travel emergency Jam! Thanks!

Customer Question

What is the safe operating temperature range for a Hino h07c engine

 

Optional Information:
Year: 1989

Submitted: 1170 days and 21 hours ago.
Category: Heavy Equipment
Value: $18
Status: CLOSED
Picture
Expert:  wayne replied 1170 days and 12 hours ago.

Hi I'm Wayne,
I will help you with this.
A good safe operating temp for the engine is 185- 205 degree.
lower temp, will give you unburned fuel, and lot of smoke, Higher temp., will cause over heat and my cause engine damage.

If this helped you, please hit Accept. if not get back to me. Cool

Customer replied 1170 days and 1 hours ago.

Wayne,
Thanks for your answer. Are your temperatures in Fahrenheit or Celsius?

I have taken temperature readings from a number of places using an electronic laser thermometer (on the surface of the block, head, radiator, sender unit and radiator pipes) at various intervals during aXXXXXand whilst most readings have been 94C (201F) or less I have measured temperature readings as high as 104 Celsius (219F) on the block and sender unit. One measurement of the block after stopping got to 115C (239F).

Is this of concern?

Thanks again, Graham

Accepted Answer

Picture
Expert:  wayne replied 1170 days ago.

HI GramHemsworth,

Mine are in ( F),

If you are runninng 219, that is very high, not boarder line high,I would replace Thermostats, clean/ flush radiator, and blow out A/C condener coil,if you have the this.
This will bring Temp., down.

Thanks, Wayne

Expert TypeJourneyman
Category: Heavy Equipment
Pos. Feedback: 96.0 %
Accepts: 2941
Answered: 1/31/2010

Experience: 34 years experiance as engine rebuild and problems.Thermo-King repair and trouble shooting.

Ask this Expert a Question >
Customer replied 1169 days and 23 hours ago.

Wayne,
Thanks again...I have tried all those suggestions but with no luck...Graham

PS If you have any other suggestions they are more than welcome.

Picture
Expert:  wayne replied 1169 days and 12 hours ago.

Morning Graham,

I did not notice in your last answer, 239 is this normal??, Well yes, the block always gets hotter when engine off, Due to no coolant circulating,.

Did you make sure your fan is kicking in, (fan Clutch), or the belts are good and tight, (belt Driven).
other things that would cause high temp, Fan shroud, broke/missing, Engine timing.

Thanks, WayneCool

Customer replied 1168 days and 23 hours ago.

Wayne,

I have checked the fan and belts and they are all OK.

I have looked closely at the temperature data and I think the radiator isn't reducing the water temperature very much (water coming from the radiator is running only around 7C less than the water going into it). So I think I am off to get the radiator re-cored or replaced.

 

Thanks again for you r help, Graham

Picture
Expert:  wayne replied 1168 days and 12 hours ago.

Thank You, XXXXX

 
Tweet

3 Technicians are Online Right Now

Ask Your Question Now
Heavy Equipment Questions Date Submitted
I JUST GOT A WOODSMAN MX18 WOOD CHIPPER.IT WONT THROW THE CHIPS 4/2/2013
Cat Man: I was wondering if you knew what Heavy Equipment 3/29/2013
Have a 4300 international w/ dt 466. Stopped running. Codes 3/6/2013
What is the valve and injector clearance on a 471 Detroit engine 3/5/2013
RA-CI 3/3/2013
i just purchased a 1970 john derre tractor loader back hoe 3/1/2013
I would like to know the differences in the engine blocks between 2/25/2013
I require a Decal for Eaton 10 speed RTO-610 gear shift pattern 2/15/2013
Hello. I have a Komatsu D-20A Dozer. Late last fall starting 2/4/2013
Have an Eaton Series 40 Steering Control Unit that I am trying 2/1/2013
RSS
Next 10 >
Ask A Technician
Type Your Heavy Equipment Question Here...
characters left:

Top Heavy Equipment Experts

See More Technicians

In The News

Nbc
Washington Post
New York Times
Cnn
Learn More

How It Works

  • Ask an Expert
  • Get a Professional Answer
  • Ask Followup Questions
  • 100% Satisfaction Guarantee
Learn More
close
Find Expert answers related to your question.
Sign up using email
We will never post anything without your permission.
Already have an account? Sign in

Ask a Technician

Get a Professional Answer. 100% Satisfaction Guaranteed.
190 Technicians are Online Now
Type Your Heavy Equipment Question Here...
characters left:
Disclaimer: Information in questions, answers, and other posts on this site ("Posts") comes from individual users, not JustAnswer; JustAnswer is not responsible for Posts. Posts are for general information, are not intended to substitute for informed professional advice (medical, legal, veterinary, financial, etc.), or to establish a professional-client relationship. The site and services are provided "as is" with no warranty or representations by JustAnswer regarding the qualifications of Experts. To see what credentials have been verified by a third-party service, please click on the "Verified" symbol in some Experts' profiles. JustAnswer is not intended or designed for EMERGENCY questions which should be directed immediately by telephone or in-person to qualified professionals.
Truste
Contact Us | Terms of Service | Privacy & Security | About Us
© 2003-2013 JustAnswer LLC