How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Jerry Your Own Question
Jerry
Jerry, Master Mechanic
Category: GM
Satisfied Customers: 17218
Experience:  ASE Master tech, 30 years experience GM certified
2947720
Type Your GM Question Here...
Jerry is online now
A new question is answered every 9 seconds

Gmc: secondary air injection system malfuction code..p0410

Resolved Question:

the computer stores that secondary air injection system malfuction code p0410 01 jimmy gmc 4.3 liter
Submitted: 7 years ago.
Category: GM
Expert:  Jerry replied 7 years ago.

Hello and welcome to Just answer.com, Super mechanic here. About your vehicle.

 

There has been a service bulletin for that type of concern. Here is what it states.

 

 

Bulletin No.: 04-06-04-015A

Date: November 28, 2006

TECHNICAL

Subject:
LN2, L43 or L35 Engine SES/MIL Light Illuminated, AIR Pump Ingesting Water and DTC P0410 Set (Replace AIR Pump and Inlet Hose Assembly)

 

Models:
1999-2003 Chevrolet Blazer, S10
1999-2001 GMC Jimmy
1999-2003 GMC Sonoma
1999-2001 Oldsmobile Bravada

 

with Vortec 2.2L I4 or 4.3L V6 Engine (VINs 4, 5, W - RPOs LN2, L43, L35)

Supercede:

This bulletin is being revised to remove a part number and change the two AIR pump part numbers in the Parts Information. Please discard Corporate Bulletin Number 04-06-04-015 (Section 06 - Engine/Propulsion System).

Condition

Some customers may comment on the SES/MIL light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.

Cause

Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.

Correction

Replace the AIR pump and install a new inlet hose and solenoid tube assembly using the following procedure:

Raise the vehicle on a hoist.

Remove the shield covering the AIR pump.

Remove the hose and vacuum lines from the pump and solenoid.

Remove the AIR pump inlet hose. Do not re-use the hose.

Disconnect the electrical connectors from the pump and solenoid.

Remove the pump mounting bolts and pump.

Transfer the isolators from the old pump to the new pump.

Install the new AIR pump and bolts to the vehicle.

Tighten

Tighten the bolts to 17 N.m (12.5 lb ft).

Route the new hose assembly up between the engine and fender. The hose should come up near the area between the battery and the coolant bottle.

Connect the new inlet hose to the pump inlet.

Connect the old outlet hose to the pump outlet.

Connect the electrical connector to the pump.

Connect the electrical connector for the solenoid to the connector on the new hose assembly.

Connect the hose with the white nipple to the vacuum source hose.

Connect the remaining hose to the shut off valve.

Install the shield covering the AIR pump.

Lower the vehicle.

Remove the coolant reservoir nut nearest the battery.

Route the new hose assembly between the battery and the coolant reservoir with the solenoid on top.

Install the solenoid bracket onto the coolant reservoir stud and reinstall the nut back into the vehicle.

Use a wire tie to keep the new hose assembly away from the engine. On four cylinder engines, tie to the AIR outlet hose. On six cylinder engines, tie to an available hole in the radiator fan shroud.

 

 

 

 

graphic

Jerry and 3 other GM Specialists are ready to help you