How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Wrenchtech Your Own Question
Wrenchtech
Wrenchtech, ASE Certified Technician
Category: Ford
Satisfied Customers: 1403
Experience:  40 years experience with ASE certification as Master Technician with L1--Repair Shop Owner
7136321
Type Your Ford Question Here...
Wrenchtech is online now
A new question is answered every 9 seconds

Engine bolt torque specification for a 2002 ford focus sohc?

This answer was rated:

what is the engine bolt torque specification for a 2002 ford focus sohc?
Are you asking for the head bolt torque?
Customer: replied 8 years ago.
Head bolt and connecting rod bolt torque
This should give you everything you need.



Intake manifold nuts Stage 1: 10 ft. lbs.
Stage 2: +90 degrees
Intake manifold bracket nuts and bolts 89 inch lbs.
Front engine accessory drive bracket bolts 35 ft. lbs.
Front engine accessory drive bracket nuts 35 ft. lbs.
A/C compressor bolts 18 ft. lbs.
Upper generator bolts 35 ft. lbs.
Lower generator bolt 35 ft. lbs.
EGR valve to intake manifold 18 ft. lbs.
EGR valve to EGR manifold tube 18 ft. lbs.
EGR manifold tube to exhaust manifold 53 inch lbs.
Flexible exhaust pipe 35 ft. lbs.
Exhaust manifold nuts
20 ft. lbs.
Catalytic converter to exhaust manifold bolts 30 ft. lbs.
Oil control plug, iB5 transmission 26 ft. lbs.
Thermostat housing 10 ft. lbs.
Starter motor to transaxle 26 ft. lbs.
Lower transaxle flange bolts 35 ft. lbs.
Upper transaxle flange bolts 35 ft. lbs.
Left-hand transaxle flange bolts 35 ft. lbs.
Engine roll restrictor to transaxle 35 ft. lbs.
Engine roll restrictor to subframe 35 ft. lbs.
Rear engine mounting to body 35 ft. lbs.
Rear engine mounting (nut on transmission mounting bracket) 98 ft. lbs.
Front engine mounting to engine 59 ft. lbs.
Front engine mounting to body 35 ft. lbs.
Wheel nuts 94 ft. lbs.
Suspension strut to body 35 ft. lbs.
Lower suspension arm ball joint to spindle carrier 35 ft. lbs.
Power steering pump 17 ft. lbs.
Power steering pump pulley 35 ft. lbs.
Cylinder head bolts
Tighten all bolts in a single sequence
Note: Always install new cylinder head bolts.
50 Nm
Back the bolts off 1/2 turn.
Tighten the bolts in sequence shown to 50 Nm
see note
Note: Rotate all the bolts in a single sequence an additional 180 degrees in two steps of 90 degrees each.
Timing belt tensioner 18 ft. lbs.
Spark plugs 11 ft. lbs.
Oil level indicator tube 89 inch lbs.
Valve cover bolts 80 inch lbs.
Ignition coil (El) bracket to cylinder head 89 inch lbs.
Rocker arms 18 ft. lbs.
Camshaft thrust plate bolts 89 inch lbs.
Camshaft pulley bolt 77 ft. lbs.
Camshaft position sensor (CMP) 18 ft. lbs.
Oil pressure switch 10 ft. lbs.
Oil pump 10 ft. lbs.
Oil pump tube 89 inch lbs.
Coolant pump 18 ft. lbs.
Oil intake pipe to oil pump 89 inch lbs.
Main bearing bolts 73 ft. lbs.
Rear crankshaft oil seal retainer 18 ft. lbs.
Big end (rod) bearing cap nuts (stage 1) 28 ft. lbs.
Intermediate shaft bracket 35 ft. lbs.
Oil pan to crankcase 18 ft. lbs.
Oil pan baffle 18 ft. lbs.
Upper timing belt cover 35 ft. lbs.
Lower timing belt cover 89 inch lbs.
Engine oil drain plug 18 ft. lbs.
Knock sensor 15 ft. lbs.
Flywheel 60 ft. lbs.
Crankshaft position sensor 53 inch lbs.
Crankshaft pulley 89 ft. lbs.
Battery tray 18 ft. lbs.

Wrenchtech and other Ford Specialists are ready to help you