How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask TIM Your Own Question
TIM
TIM, SERVICE MANAGER
Category: Dodge
Satisfied Customers: 6277
Experience:  DODGE SERVICE MANAGER- 20 + YEARS
6531745
Type Your Dodge Question Here...
TIM is online now
A new question is answered every 9 seconds

Dodge RAM 2500 4x4: Where is the exhaust filter located on

Resolved Question:

Where is the exhaust filter located on my 08 Ram diesel and how do I clean it
Submitted: 5 years ago.
Category: Dodge
Expert:  TIM replied 5 years ago.
TIM : this filter is located in the exhaust pipe-- before caty converter-- in owners manual is procedure for cleaning by driving it
TIM : if you need procedure let me know -- and I will post it for you
TIM :
EVIC Message Center - Message - Catalyst Full

The engine Electronic Control Module (ECM) monitors the soot load in the diesel particulate filter. Under normal operating conditions the diesel particulate filter is self-cleaning, where accumulated soot is converted to ash. Under light load operating conditions, the driver may be notified via the vehicle's Electronic Vehicle Information Center (EVIC) message center "CATALYST FULL: SEE OWNERS MAN" will be displayed on the overhead console of your vehicle if the exhaust particulate filter reaches 80% of its maximum storage capacity. Under conditions of exclusive short duration and low speed driving cycles, your Cummins engine and exhaust aftertreatment system may never reach the conditions required to remove the trapped PM. If this occurs, “Catalyst Full See Owner Manual” will be displayed on the overhead console in your vehicle. If this message is displayed you will hear one chime to assist in alerting you of this condition. Catalyst Stat::::::::::80% Catalyst Stat::::::::::80% will replace the message “Catalyst Full See Owner Manual” after it is displayed for one minute. The engine Powertrain Control Module (PCM) will continue to monitor the amount of particulate matter trapped in the particulate filter. This message indicates the percentage of the particulate filter capacity that has been used. By simply driving your vehicle at highway speeds for as little as 45 minutes you can remedy the condition in the particulate filter system and allow your Cummins engine and exhaust aftertreatment system to remove the trapped PM and restore the system to normal operating condition. Catalyst Stat:::::::::::80%, 90%, 99% Catalyst Stat:::::::::::80%, 90%, 99% If you are unable to drive your vehicle under these conditions for an extended period of time after the initial warning notification, the Engine PCM will continue to monitor the particulate filter and will display the progression of particulate filter usage (80, 90, 99%) on the EVIC message center. CATALYST FULL SERVICE REQD If the particulate filter reaches 99% of its capacity, the overhead console in your vehicle will chime twice and display the message CATALYST FULL SERVICE REQD. At this point the engine PCM will register a fault code, the instrument panel will display a MIL light and the engine PCM will derate the truck, reducing its horsepower and torque output. The PCM derates the engine in order to limit the likelihood of permanent damage to the aftertreatment system. If this condition is not corrected and a dealer service is not performed, extensive exhaust aftertreatment damage can occur. In order to correct this condition it will be necessary to have the truck serviced by your local authorized dealer.
Intervention Regeneration Strategy – EVIC Message Process Flow (Late Build) The Cummins diesel engine meets all EPA Heavy Duty Diesel Engine Emissions Standards, resulting in the lowest emitting diesel engine ever produced. NOTE: Depending on the build date of your vehicle or if the software has been updated, the EVIC may display the following messages. To achieve these emissions standards, your vehicle is equipped with a state-of-the-art engine and exhaust system. The engine and exhaust after-treatment system work together to achieve the EPA Heavy Duty Diesel Engine Emissions Standards. These systems are seamlessly integrated into your vehicle and managed by the Cummins Powertrain Control Module (PCM). The PCM manages engine combustion to allow the exhaust system’s catalyst to trap and burn Particulate Matter (PM) pollutants, with no input or interaction on your part. Additionally, the overhead console in your vehicle has the ability to alert you to additional maintenance required on your truck or engine. Refer to the following messages that may be displayed on your Electronic Vehicle Information Center (EVIC):
Exhaust System — Regeneration Required Now “Exhaust System—Regeneration Required Now” will be displayed on the overhead console of your vehicle if the exhaust particulate filter reaches 80% of its maximum storage capacity. Under conditions of exclusive short duration and low speed driving cycles, your Cummins diesel engine and exhaust aftertreatment system may never reach the conditions required to remove the trapped PM. If this occurs, “Exhaust System — Regeneration Required Now” will be displayed on the overhead console in your vehicle. If this message is displayed, you will hear one chime to assist in alerting you of this condition. By simply driving your vehicle at highway speeds for as little as 45 minutes, you can remedy the condition in the particulate filter system and allow your Cummins diesel engine and exhaust after-treatment system to remove the trapped PM and restore the system to normal operating condition. Exhaust Filter XX% Full Indicates that the Diesel Particulate Filter (DPF) is approaching full. Exhaust System — Regeneration in Process Indicates that the Diesel Particulate Filter (DPF) is selfcleaning. Maintain your current driving condition until regeneration is completed. Exhaust System — Regeneration Completed Indicates that the Diesel Particulate Filter (DPF) selfcleaning is completed. If this message is displayed, you will hear one chime to assist in alerting you of this condition. Service Required — See Dealer Now Regeneration has been disabled due to a system malfunction. At this point the engine PCM will register a fault code, the instrument panel will display a MIL light. IMMEDIATE SERVICE IS REQUIRED. See your authorized dealer as damage to the exhaust system could occur soon with continued operation. Exhaust Filter Full — Power Reduced See Dealer The PCM derates the engine in order to limit the likelihood of permanent damage to the after-treatment system. If this condition is not corrected and a dealer service is not performed, extensive exhaust after-treatment damage can occur. In order to correct this condition it will be necessary to have your vehicle serviced by your local authorized dealer. IMMEDIATE SERVICE IS REQUIRED. See your authorized dealer, as damage to the exhaust system could occur soon with continued operation.
TIM :


Perform Service

The 6.7L Cummins



t

engine utilizes a Closed Crankcase
Ventilation (CCV) system, EGR valve and an EGR cooler.

This system filters and recycles gasses produced in the

crankcase during the normal combustion process. “Perform

Service” will be displayed on the overhead console

of your vehicle if the CCV filter, EGR valve and EGR

cooler are due for required maintenance. The CCV filter is




TIM :
located on the top of the engine valve cover. For additional
information, see your local authorized dealer.

Catalyst Full See Owner Manual


“Catalyst Full See Owner Manual” will be displayed on

the overhead console of your vehicle if the exhaust

particulate filter reaches 80% of its maximum storage

capacity. Under conditions of exclusive short duration

and low speed driving cycles, your Cummins


t



Catalyst Stat::::::::::80%


Catalyst Stat::::::::::80% will replace the message “Catalyst

Full See Owner Manual” after it is displayed for one

minute. The engine Powertrain Control Module (PCM)

will continue to monitor the amount of particulate matter

trapped in the particulate filter. This message indicates

the percentage of the particulate filter capacity that has

been used.

By simply driving your vehicle at highway speeds for as

little as 45 minutes you can remedy the condition in the

particulate filter system and allow your Cummins


t



Catalyst Stat:::::::::::80%, 90%, 99%


Catalyst Stat:::::::::::80%, 90%, 99% If you are unable to

drive your vehicle under these conditions for an extended

period of time after the initial warning notification,

the Engine PCM will continue to monitor the

particulate filter and will display the progression of

particulate filter usage (80, 90, 99%) on the EVIC message

center



engine



and exhaust aftertreatment system to remove the

trapped PM and restore the system to normal operating

condition.


engine



and exhaust aftertreatment system may never reach the

conditions required to remove the trapped PM. If this

occurs, “Catalyst Full See Owner Manual” will be displayed

on the overhead console in your vehicle. If this

message is displayed you will hear one chime to assist in

alerting you of this condition.
Expert:  TIM replied 5 years ago.
IF AL SET -PLEASE CLICK THE ACCEPT BUTTON -- ANY MORE INFO REQUIRED--PLEASE LET ME KNOW
TIM and 4 other Dodge Specialists are ready to help you