How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Shawn Your Own Question
Shawn
Shawn, ASE Certified Technician
Category: Dodge
Satisfied Customers: 655
Experience:  PA Certified Inspection emissions, ASE Brakes Suspension, Lead diagnostic Tech.20 years exp
9265294
Type Your Dodge Question Here...
Shawn is online now
A new question is answered every 9 seconds

What are the torque specifictions for a 2008 5.

This answer was rated:

what are the torque specifictions for a 2008 5.7 hemi when installing a cam
Customer

Here are the complete torque specs for the 5.7 Hemi


5.7L - SERVICE INFORMATION

 


TORQUE

TORQUE CHART 5.7L ENGINE
DESCRIPTION N.m Ft. In.
Lbs. Lbs.
Block Pipe Plugs 20 - 177
(1/4 NPT)
(3/8 NPT) 27 - 240
Camshaft Sprocket-Bolt 122 90 -
Camshaft Tensioner Plate-Bolts 28 - 250
Coil to Cylinder Head Cover-Bolts 7 - 62
Timing Chain Case Cover-Bolts 28 - 250
Lifting Stud 55 40 -
Connecting Rod Cap-Bolts 21 15 -
plus 90° plus 90°
Turn Turn
Main Bearing Cap-Bolts 27 - -
M-12 plus 90°
Turn
Crossbolts 28 - -
M-8
Cylinder Head-Bolts
M-12 Bolts
Step 1 34 25 -
Step 2 54 40 -
Step 3 Turn 90° Turn 90°-
M-8 Bolts - - -
Step 1 20 15 -
Step 2 34 25 -
Cylinder Head Cover-Bolts 8 - 70
Exhaust Manifold to Cylinder Head 25 - 220
Flexplate to Crankshaft-Bolts 95 70 -
Flywheel to Crankshaft-Bolts 75 55 -
Front Insulator-Thru bolt/nut 95 70 -
Front Insulator to Support Bracket
-Stud Nut (4WD) 41 30 -
-Through Bolt/Nut (4WD) 102 75 -
Front Insulator to Block-Bolts 95 70 -
(2WD)
Generator-Mounting Bolt 55 40 -
Intake Manifold-Bolts Refer to Procedure
Lifter Guide Holder 12 - 106
Oil Pan Bolts 12 - 105
Oil Dipstick Tube 12 - 105
Oil Pan-Drain Plug 34 25 - Oil Pump-Attaching Bolts 28 - 250
Oil Pump Pickup Tube - Bolt and Nut 28 - 250
Rear Seal Retainer Attaching Bolts 15 - 132
Rear Insulator to Bracket- 68 50 -
Through-Bolt (2WD)
Rear Insulator to Crossmember 41 30 -
Support Bracket-Nut (2WD)
Rear Insulator to Crossmember- 68 50 -
Nuts (4WD)
Rear Insulator to Transmission- 68 50 -
Bolts (4WD)
Rear Insulator Bracket-Bolts 68 50 -
(4WD Automatic)
Rear Support Bracket to 41 30 -
Crossmember Flange-Nuts
Rear Support Plate to Transfer 41 30 -
Case-Bolts
Rocker Arm-Bolts 22 - 195
Spark Plugs - - -
Thermostat Housing-Bolts 28 - 250
Throttle Body-Bolts 12 - 105
Transfer Case to Insulator 204 105 -
Mounting Plate-Nuts
Transmission Support Bracket- 68 50 -
Bolts (2WD)
Vibration Damper-Bolt 176 129 -
Water Pump to Timing Chain 28 - 250
Case Cover-Bolts



5.7L - SERVICE INFORMATION -


INSTALLATION

1.Install intake manifold seals.
2.Position intake manifold and IAFM.
3.Install intake manifold retaining bolts, and tighten in sequence
from the middle bolts towards the outside in a crisscross
pattern. Torque fasteners to 12 N.m (105 in. lbs.).
4.Connect electrical connectors for the following components:
Manifold Absolute Pressure (MAP) Sensor
Intake Air Temperature (IAT) Sensor
Throttle Position (TPS) Sensor
Coolant Temperature (CTS) Sensor
Idle Air Control (IAC) Motor
5.Install generator.
6.Install A/C compressor.
7.Connect Brake booster hose and Positive crankcase ventilation
(PCV) hose.
8.Install resonator assembly and air inlet hose.
9.Connect negative cable to battery.


 

 

 

 

 

Shawn

Shawn and 3 other Dodge Specialists are ready to help you