How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Mike Your Own Question
Mike
Mike, Consultant
Category: Clock Repair
Satisfied Customers: 2841
Experience:  I've been active in clock repair for 14 years - NAWCC member.
61108514
Type Your Clock Repair Question Here...
Mike is online now
A new question is answered every 9 seconds

I have a Harfen-Gong (GB 4) and need a winding key. Can you help ***** *****g (Clearwat

Customer Question

I have a Harfen-Gong (GB 4) and need a winding key. Can you help
***** *****g (Clearwater, Florida)
Submitted: 1 year ago.
Category: Clock Repair
Expert:  Mike replied 1 year ago.
Hi Douglas, My name is ***** ***** it is my pleasure to assist you. Does your key need a 2 ended key or 1? Thanks Mike
Expert:  Mike replied 1 year ago.
Hi Douglas, If your Gustav Becker doesn't need the double ended key which I don't think it does you can order your key from Clockworks with the information below. You can order a universal key with 6 different size keys or I'll give you a chart to tell the size. Thanks Mike
.
.
If you need further assistance, please don't hesitate to ask.
PLEASE remember if you're satisfied with my answer rate my answer
" OK SERVICE " or higher so I will be compensated by JustAnswer
for helping you.
.
.
Clockworks
PO Box 339
124 Goss Hill
Huntington, MA 01050 USA (###) ###-####
Mon 9-5 Tues-Fri 12-5pm EST
.
.
Clock key sizing chart.
.
Shaft width / Key #
•1.75mm = 000 Key
•2.0mm = 00 Key
•2.25mm = 0 Key
•2.5mm = 1 Key
•2.75mm = 2 Key
•3.0mm = 3 Key
•3.25mm = 4 Key
•3.5mm = 5 Key
•3.75mm = 6 Key
Shaft width / Key #
•4.0mm = 7 Key
•4.25mm = 8 Key
•4.5mm = 9 Key
•4.75mm = 10 Key
•5.00mm = 11 Key
•5.25mm = 12 Key
•5.5mm = 13 Key
•5.75mm = 14 Key
•6.0mm = 15 Key
.
.
To get the key you need, measure the shaft the key is to go on to, then use this chart to get the key size # ***** need. Please do not call asking what key your clock needs, as you will be told it would still have to be measured. Again, you are measuring the shaft that the key goes onto in MM and then using the above chart.
Expert:  Mike replied 1 year ago.
www.clockworks.com › Clock Parts
Expert:  Mike replied 1 year ago.
Hi Douglas, I was wondering if you need further assistance with your clock key? Thanks Mike
Expert:  Mike replied 1 year ago.
Hi Douglas, I was wondering if you need further assistance with your clock key? Thanks Mike
Expert:  Mike replied 1 year ago.
Hi Douglas, I was wondering if you need further assistance with your clock key? Thanks Mike
Expert:  Mike replied 1 year ago.
Hi , I was wondering if you need further assistance with your clock? Thanks Mike
Expert:  Mike replied 1 year ago.
Hi Douglas if the #4 key was to small double check the measurement of the shaft again to make sure the millimeters are correct and order a # ***** or remember you can also order the universal key with 6 different sizes. Thanks Mike
.
.
If you need further assistance, please don't hesitate to ask.
PLEASE remember if you're satisfied with my answer rate my answer
" OK SERVICE " or higher so I will be compensated by JustAnswer
for helping you.

Related Clock Repair Questions