How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Brad Barker Your Own Question
Brad Barker
Brad Barker,
Category: Chrysler
Satisfied Customers: 4
Experience:  Master Kia technician at Kia
96268722
Type Your Chrysler Question Here...
Brad Barker is online now
A new question is answered every 9 seconds

Right front right window once it goes down wont come up I

Customer Question

Hi,right front right window once it goes down wont come up I can hear the motow working but like every 5 mins it will go like an inch then stops working
JA: What year is your MINI?
Customer: 2000
JA: Are you fixing your MINI yourself? What have you tried so far?
Customer: yes can figure ouy how to remove the door panel
JA: Anything else you want the mechanic to know before I connect you?
Customer: cant
Submitted: 4 months ago.
Category: Chrysler
Expert:  Brad Barker replied 4 months ago.

what kind of vehicle are you dealing with?

Customer: replied 4 months ago.
2000 Chrysler town
Expert:  Brad Barker replied 4 months ago.

does the motor stop working when it stops moving up or does it keep trying?

Customer: replied 4 months ago.
stops working
Expert:  Brad Barker replied 4 months ago.

the window regulator is getting slack in the cables and binding the window on the way up and the internal circuit breaker is tripping in the motor. when you let it sit the breaker cools off and it allows the motor to run again. I would recommend replacing the window regulator and motor assembly.

Customer: replied 4 months ago.
ok.i guess ill go to the Chrysler dealer and have them do the job better. thanks
Expert:  Brad Barker replied 4 months ago.
  • EMOVAL AND REPLACEMENT

WINDOW REGULATOR

REMOVAL

  1. Remove the watershield. Refer to Front Door Panel.

Fig. 16

  1. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent (Fig. 16).
  2. Disconnect wire connector from power window motor, if equipped.

Fig. 17

  1. Loosen screws attaching front and rear window guide rails to inner door panel (Fig. 17).
  2. Remove screw heads on guide rails from key hole slots in inner door panel.
  3. Loosen screws attaching regulator to inner door panel.
  4. Remove regulator from inner door panel.

Fig. 18

  1. Extract rear guide rail through inner door panel rear access hole (Fig. 18).
  2. Extract front guide rail through front access hole.

INSTALLATION

  1. Insert front guide rail through front access hole.
  2. Insert rear guide rail through rear access hole.
  3. Place window regulator in position on inner door panel.
  4. Place screw heads on guide rails in position through key hole slots in inner door panel.
  5. Tighten screws to attach front and rear guide rails to inner door panel.
  6. Connect wire connector into power window motor, if equipped.
  7. Install door glass.
  8. Verify door glass alignment and operation.
  9. Install sound shield and door trim panel.

© 2016 ALLDATA LLC. All rights reserved. Terms and Conditions

Expert:  Brad Barker replied 4 months ago.
  • FRONT DOOR TRIM PANEL

REMOVAL

  1. Using a trim stick (C-4755), pry courtesy lamp from door trim.
  2. Disconnect wire connector from courtesy lamp.
  3. If equipped, remove screws attaching door assist handle to inner door panel.
  4. If equipped, remove screw attaching door pull cup to inner door panel.
  5. If equipped, remove screws attaching trim panel to door from below map pocket.
  6. If equipped, remove window crank.
  7. Using a trim stick, remove screw cover from switch panel.
  8. Remove screws attaching switch panel to door trim.

Fig.32 Front Door Switch Panel

  1. Remove power accessary switch from door trim.
  2. Disconnect power switch from wire connector.

Fig.33 Memory Seat/Mirror Switch

  1. If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector.
  2. If equipped, remove screw holding door trim to door panel from behind inside latch release handle.

Fig.34 Front Door Trim Panel

  1. Disengage clips attaching door trim to door frame around perimeter of panel.
  2. Lift trim panel upward to disengage flange from inner belt molding at top of door.
  3. Tilt top of trim panel away from door to gain access to latch linkage.

Fig.35 Inside Door Handle Linkage

  1. Disengage clip attaching linkage rod to inside latch release handle.
  2. Separate linkage rod from latch handle.
  3. Remove front door trim panel from vehicle.

INSTALLATION

  1. Hold top of trim panel away from door to gain access to latch linkage.
  2. Place linkage rod in position on latch handle.
  3. Engage clip to hold linkage rod to inside latch release handle.
  4. Place front door trim panel in position on door.
  5. Install trim panel into inner belt molding at top of door.
  6. Install clips to attach door trim to door frame around perimeter of panel.
  7. If equipped, install screw to attach door trim to door panel behind inside latch release handle.
  8. If equipped, connect power switch into wire connector.
  9. Place power accessary switch in position on door trim.
  10. Connect wire connector into memory seat/mirror switch and install switch into trim panel.
  11. Install screws to attach accessary switch panel to door trim.
  12. Install screw cover into switch panel.
  13. If equipped, install window crank.
  14. If equipped, install screws to attach trim panel to door inside map pocket.
  15. If equipped, install screw to attach door pull cup to inner door panel.
  16. If equipped, install screws to attach door assist handle to inner door panel.
  17. Connect wire connector into courtesy lamp.
  18. Install lamp in door trim.
Expert:  Brad Barker replied 4 months ago.

first one is regulator removal second one should have been first it is procedure to remove door panel

Customer: replied 4 months ago.
ok Thanks a lot.
Expert:  Brad Barker replied 4 months ago.

no problem

Related Chrysler Questions