How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask sprinkles08 Your Own Question
sprinkles08
sprinkles08, ASE Certified Technician
Category: Chrysler
Satisfied Customers: 21829
Experience:  ASE Master & Advanced level certified, Chrysler Master Certified, Trans and Hybrid Specialist
9825021
Type Your Chrysler Question Here...
sprinkles08 is online now
A new question is answered every 9 seconds

Chrysler PT Cruiser: repaired 2007 pt cruiser engine. checked

Customer Question

repaired 2007 pt cruiser engine. checked all sensors. timing checked. no power to automatic sensor relay in fuel box. will not crank or start
Submitted: 9 months ago.
Category: Chrysler
Customer: replied 9 months ago.
(Posted by JustAnswer at customer's request) Hello. I would like to request the following Expert Service(s) from you: Live Phone Call. Let me know if you need more information, or send me the service offer(s) so we can proceed.
Customer: replied 9 months ago.
It has been a while. not response
Expert:  sprinkles08 replied 9 months ago.
Hello and welcome to JustAnswer!If there is no power to the fuse that powers the ASD relay, fuse 18 in the TIPM, and the positive cable to the TIPM is intact and it's connection is good, then there is an internal failure in the TIPM and it will need to be replaced.
Customer: replied 8 months ago.
There is power to fuse 18
Customer: replied 8 months ago.
No power to fuses 23 26 25
Customer: replied 8 months ago.
No power to fuse 32
Expert:  sprinkles08 replied 8 months ago.
How are you checking for power at these fuses?
Customer: replied 8 months ago.
With ohm meter
Expert:  sprinkles08 replied 8 months ago.
Under what conditions are you checking though? The ASD circuit won't be powered if the key is simply turned on and then you go out and check.
Customer: replied 8 months ago.
Can you tell me how to check?
Expert:  sprinkles08 replied 8 months ago.
Unplug an injector and set up a test light to monitor power on the dark green/orange wire. Does it have power for one second when the key is first turned on?
Customer: replied 8 months ago.
No power
Customer: replied 8 months ago.
There is no power
Expert:  sprinkles08 replied 8 months ago.
Does the relay click when the key is turned on?Are there two power feeds at the relay?
Customer: replied 8 months ago.
No relay click
Customer: replied 8 months ago.
No power to injector
Expert:  sprinkles08 replied 8 months ago.
Are there two power feeds at the ASD relay?
Customer: replied 8 months ago.
Yes.
Expert:  sprinkles08 replied 8 months ago.
If you jump pin 30 to 87 does it power theininjectors?
Customer: replied 8 months ago.
Did you mean 37 and 30
Customer: replied 8 months ago.
No power to injectors
Expert:  sprinkles08 replied 8 months ago.
You jumped the terminals that engage relay pins 30 and 87 and there was no power at the injectors?
Customer: replied 8 months ago.
I do not know where 87 is. I jumped 30 and 37
Expert:  sprinkles08 replied 8 months ago.
There isn't a pin 37. Relay terminals are 30, 85, 86,87 and 87a.
Customer: replied 8 months ago.
I was referring to numbers on fuel box cover. Not sure where those numbers are.
Expert:  sprinkles08 replied 8 months ago.
Im not sure what you're referring to as a fuel box. You're testing at the ASD relay on the cowl.
Customer: replied 8 months ago.
I found it
Expert:  sprinkles08 replied 8 months ago.
Ok.
Customer: replied 8 months ago.
Nothing happened. No power. There are 2 relays with same markings.
Customer: replied 8 months ago.
One relay ha power. The other doesn't
Expert:  sprinkles08 replied 8 months ago.
Look at the wires leaving the relays and determine which one has the same wire you see at the injectors. This is the relay you're testing at.