How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask sprinkles08 Your Own Question
sprinkles08
sprinkles08, ASE Certified Technician
Category: Chrysler
Satisfied Customers: 21604
Experience:  ASE Master & Advanced level certified, Chrysler Master Certified, Trans and Hybrid Specialist
9825021
Type Your Chrysler Question Here...
sprinkles08 is online now
A new question is answered every 9 seconds

04 Sebring with codes P0032, P0038, P0052,P0058, P0888,

Customer Question

04 Sebring with codes P0032, P0038, P0052,P0058, P0888, P0700, P0499. I would like to know what all these systems have in common. Is there a ground or power splice that I can look at.
Submitted: 1 year ago.
Category: Chrysler
Expert:  sprinkles08 replied 1 year ago.

Hello and welcome to JustAnswer!

You have at least a few different problems going on. The trans codes, leak detection pump code and oxygen sensor codes are separate issues.

Does the trans not shift?

Do you have the VIN?

Where specifically did you find green wiring?

Customer: replied 1 year ago.
The vin is 1c3el56r84n296608 the trans is in limp mode.
The questionable grounds are below the master cyl. And in the left front corner behind the radiator support.
Expert:  sprinkles08 replied 1 year ago.

Do you know for sure if the oxygen sensor codes starting setting all at once?

Customer: replied 1 year ago.
the 02 codes all came at once. The first was the leak pump a while ago. Then the trans last week. Now O2 codes.
Expert:  sprinkles08 replied 1 year ago.

I'm a full time tech and at work this morning, I'll get back to you as quickly as I can!

Customer: replied 1 year ago.
Thanks
Expert:  sprinkles08 replied 1 year ago.

Can you try swapping the EATX relay and see if it then shifts?

Customer: replied 1 year ago.
Sure
Expert:  sprinkles08 replied 1 year ago.

Let me know how it goes!

Customer: replied 1 year ago.
Still in limp mode
Expert:  sprinkles08 replied 1 year ago.

Do you have a test light?

Customer: replied 1 year ago.
im an old tech with no access to schematics.
Expert:  sprinkles08 replied 1 year ago.

Are there two power feeds at the EATX relay with the key on?

Customer: replied 1 year ago.
There is only one power feed to the relay. If you want to give me a couple of steps I may be able to save you some time.
Expert:  sprinkles08 replied 1 year ago.

Does one terminal have ground?

Customer: replied 1 year ago.
With the test light hooked to the positive battery post no terminals of the relay light the light
Expert:  sprinkles08 replied 1 year ago.

Do the fog lamps and cooling fan work?

Customer: replied 1 year ago.
The fog lights work
Expert:  sprinkles08 replied 1 year ago.

Does the cooling fan work?

Customer: replied 1 year ago.
It wont get warm enough for it to come on in the rain we are having.
Expert:  sprinkles08 replied 1 year ago.

You can turn the a/c or defrost on which will run the a/c compressor an in turn the cooling fan.

Customer: replied 1 year ago.
No a/c I dont know if this is a new problem. Its not my car.
Expert:  sprinkles08 replied 1 year ago.

Have you load tested the oxygen sensor heater grounds?

Customer: replied 1 year ago.
All the wires are broken at G103 im fixing them and then ill test.
Expert:  sprinkles08 replied 1 year ago.

Ok.

Customer: replied 1 year ago.
All codes gone after repair to ground G103
Expert:  sprinkles08 replied 1 year ago.

Great!