How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Chris Your Own Question
Chris
Chris, Technician
Category: Chrysler
Satisfied Customers: 13021
Experience:  30 years certified Chrysler technician, smog license Certified Master Technician
12365498
Type Your Chrysler Question Here...
Chris is online now
A new question is answered every 9 seconds

Chrysler Sebring LX how do i remove the power window motor,

Resolved Question:

how do i remove the power window motor, drivers side 2004 sebring
Submitted: 6 years ago.
Category: Chrysler
Expert:  Chris replied 6 years ago.

Hello and welcome to just answer. Here is the procedure for you. I hope this helps, and let me know if you need more assistance with this.

 

Chris

 

Roll door glass down.
Disengage two clips attaching speaker grille to door trim panel. They are at the front of the grille, one near the top, and the other one at the bottom.
Remove three large washer-headed screws surrounding the speaker (Lower Door Trim Panel Removal).
Remove access cover at front of door trim panel. Remove by prying at its rear edge (Mirror Bezel and Door Trim Access Cover).
Remove red courtesy reflector from lower tail or door. Disengage by prying at screwdriver notch at bottom of reflector.
Remove flag trim panel from door by prying off at two attachment clips points (Mirror Bezel and Door Trim Access Cover).
Remove seven screws attaching door trim panel to door: (Lower Door Trim Panel Removal) and (Mirror Bezel and Door Trim Access Cover).
One screw is located at lower rear screw pocket.
Three screws located along the bottom of door.
One screw located inside handle opening.
One screw located at the upper front.
One screw in the pull cup.
Disengage two hidden clips attaching at the rear of the trim panel, by prying off at two attachment clip points.
Lift trim panel upward and away from door, disengage trim panel from upper retainer channel.
Disengage clip attaching latch linkage to back door handle.
Disconnect electrical connectors as necessary, including lower foot light, If equipped.
Remove door trim panel from door.

 

1 - SCREWS AT SPEAKER LOCATION
2 - BOTTOM OF DOOR TRIM PANEL

 

1 - FLAG TRIM PANEL
2 - DOOR TRIM ACCESS COVER
3 - INSIDE REMOTE HANDLE
4 - POWER DOOR LOCK SWITCH

 

  • Remove glass from regulator roller channel. Secure glass in the up position in the door frame.
  • Disconnect power window motor wire connector.
  • Loosen screw attaching regulator scissor channel to door panel.
  • Remove screw and bolt heads from keyhole slots in door panel.
  • Loosen bolts attaching regulator to door panel.
  • Remove regulator from door panel (FRONT DOOR REGULATOR).
  • Slide regulator rearward and rotate forward end of roller channel through access hole in door panel.
  •  

    1 - MOUNTING SLOTS
    2 - REGULATOR
    3 - MOUNTING BOLTS
    4 - ELECTRICAL CONNECTOR
    5 - REGULATOR
    6 - INNER DOOR
    7 - MOUNTING SLOTS

     

     

    REMOVAL MOTOR

    1. Disconnect and isolate the battery negative cable.
    2. Remove the window regulator. (Refer to 23 - BODY/DOOR - FRONT/WINDOW REGULATOR - REMOVAL).

      WARNING: FAILURE TO CLAMP THE SECTOR GEAR TO THE MOUNTING PLATE WHEN REMOVING THE MOTOR CAN RESULT IN INJURY.

    3. Secure the sector and mounting plate with a C clamp or similar clamping tool. This will prevent a sudden and forceful movement of the regulator when the motor is removed.
    4. Remove the motor from the regulator.
    Chris and 5 other Chrysler Specialists are ready to help you