How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask Kevin K Your Own Question

Kevin K
Kevin K, Owner Kevins Mobile repair Atlanta
Category: Chrysler
Satisfied Customers: 308
Experience:  14 years as a Chrysler tech,ASE cert, Master Chrysler tech
Type Your Chrysler Question Here...
Kevin K is online now
A new question is answered every 9 seconds

where is the shift solenoid pack located in a 2001 chrysler

Resolved Question:

where is the shift solenoid pack located in a 2001 chrysler 300m? and how do you remove and replace? thanks
Submitted: 4 years ago.
Category: Chrysler
Expert:  Kevin K replied 4 years ago.

Welcome to just answers my name is Kevin

The selnoid pack is inside the tranny on top of the valve body.

Here are the instructions for putting it in.

 

REMOVAL

NOTE: If valve body is being reconditioned or replaced, it is necessary to perform the Quick Learn Procedure. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/TRANSMISSION CONTROL MODULE - STANDARD PROCEDURE)

  1. Disconnect the TRS wiring connector. The solenoid wiring connector can remain attached to the case.
  2. Disconnect the shift cable from the shift lever (at the transaxle).
  3. Move the shift lever clockwise as far as it will go. This should be one position past the L position. Then remove the shift lever.
  4. Remove transaxle pan bolts (Transaxle Oil Pan Bolts).
  5. Remove transaxle oil pan (Transaxle Oil Pan). When reinstalling oil pan be sure that pan flange is clean and oil free. Apply a 1/8 inch bead of Mopar Silicone Sealer onto oil pan flange before installing.
  6. Remove oil filter from valve body (Transaxle Oil Filter). It is held in place by two clips.

    CAUTION: The 42LE transaxle oil filter is not interchangeable with the 41TE transaxle filter. Installation of a 41TE oil filter in a 42LE may cause transaxle damage.

  7. Remove valve body bolts-to-case (Valve Body Bolts).
  8. Carefully remove valve body assembly from transaxle (Valve Body From Transaxle).

    CAUTION: The overdrive and underdrive accumulators and springs may fall out when removing the valve body

  9.  

  10. .

    REMOVAL

    NOTE: If the Solenoid/Pressure Switch Assembly is being replaced, the Quick Learn Procedure must be performed. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/TRANSMISSION CONTROL MODULE - STANDARD PROCEDURE)

    1. Raise vehicle on hoist.
    2. Remove valve body assembly from transaxle. (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 42LE/VALVE BODY - REMOVAL)
    3. Remove Solenoid/Pressure Switch Assembly retaining screws from solenoid (Solenoid Retaining).
    4. Remove Solenoid/Pressure Switch Assembly and screen from valve body (Solenoid/Pressure Switch Assembly and Screen)
    5. graphic.
Kevin K, Owner Kevins Mobile repair Atlanta
Category: Chrysler
Satisfied Customers: 308
Experience: 14 years as a Chrysler tech,ASE cert, Master Chrysler tech
Kevin K and other Chrysler Specialists are ready to help you

JustAnswer in the News:

 
 
 
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
 
 
 

What Customers are Saying:

 
 
 
  • I was skeptical at first but thought I'd give it a try. I was pleasantly surprised. Your site actually is a quality service that I would recommend to others in a heartbeat. Stan Sayre, PA
< Last | Next >
  • I was skeptical at first but thought I'd give it a try. I was pleasantly surprised. Your site actually is a quality service that I would recommend to others in a heartbeat. Stan Sayre, PA
  • I AM VERY GLAD THAT I TOOK A CHANCE ON YOUR PROBLEM SOLVING SKILLS. I WAS SUCCESSFUL IN REPLACING THE FUEL PUMP. MY TRUCK RUNS LIKE A CLOCK. IT RUNS LIKE THE DAY I BOUGHT IT. NO LUNGING FORWARD, THE TURBO REACTS THE SECOND I STOMP ON THE GAS, AND IT HAS A LOT MORE POWER AND EVEN SOUNDS BETTER TO ME. IT SAVED ABOUT $500.00 BY DOING THE WORK MYSELF. I GIVE YOU ALL THE CREDIT FOR YOUR DIAGNOSING THE PROBLEM, JUST FROM THE SYMPTONS I GAVE YOU OVER THE e MAIL. I WILL USE YOUR WEB SITE AGAIN AND REFER MY FRIENDS. THANKS SO MUCH FOR THE HELP. TOM WHITTAKER USA
  • Just a quick line to tell you how pleased I am to have my brakes working properly after all this time. Your answer was what I needed. I would certainly recommend you highly. God bless! Rev. Jerry Baysinger Holts Summit, Mo
  • I recently asked a question about my 2005 dodge ram, and I just wanted to let my Expert know that he hit the nail squarely on the head with his answer. I wanted to thank him again. Greg Pittsburgh, PA
  • Just a quick line to tell you how pleased I am to have my brakes working properly after all this time. Your answer was what I needed. I would certainly recommend you highly. God bless! Jerry Holts Summit, MO
  • Thank you so much for your answer. My initial estimate was $325; I got it done for $100 - part and labor. Lynn B. Ormond Beach, FL
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
 
 
 

Meet The Experts:

 
 
 
  • Don 'Mo Lurch'

    Aftermarket & Factory Electronics

    Satisfied Customers:

    384
    Chrysler Warnty, Heavy Line Mech, Mobile Electronics. Sales, Installation & Repair for 30 years
< Last | Next >
  • http://ww2.justanswer.com/uploads/MO/molurch/2012-6-6_214526_500.64x64.png Don 'Mo Lurch''s Avatar

    Don 'Mo Lurch'

    Aftermarket & Factory Electronics

    Satisfied Customers:

    384
    Chrysler Warnty, Heavy Line Mech, Mobile Electronics. Sales, Installation & Repair for 30 years
  • http://ww2.justanswer.com/uploads/2P/2paulm/2012-4-4_183431_justabswer.64x64.jpg Paul M ASE Master's Avatar

    Paul M ASE Master

    ASE Master Tech

    Satisfied Customers:

    117
    ASE Master Tech 20+ Years
  • http://ww2.justanswer.com/uploads/MU/muddyford/2012-6-13_1204_1.64x64.png Chris (aka - Moose)'s Avatar

    Chris (aka - Moose)

    Technician

    Satisfied Customers:

    93
    16 years of experience
  • http://ww2.justanswer.com/uploads/IV/ivestoy2/2011-7-21_44030_ivan.64x64.jpg Ivan's Avatar

    Ivan

    ASE Certified Master Technician

    Satisfied Customers:

    55
    ASE Master Tech w/ 20+ years in the field. Self employed for 9 years. Member of AUTOLAB radio show.
  • http://ww2.justanswer.com/uploads/AC/acuramstr/2012-6-6_181032_me.64x64.jpg AUTOMSTR's Avatar

    AUTOMSTR

    ASE Certified Technician

    Satisfied Customers:

    0
    ASE Master Tech, L1, CA Smog ,30 YRS EXP
  • http://ww2.justanswer.com/uploads/AM/amedee/2013-10-24_23656_Amedee1.64x64.jpg Amedee's Avatar

    Amedee

    Chrysler Technician

    Satisfied Customers:

    787
    ASE Master Technician advanced level specialist
  • http://ww2.justanswer.com/uploads/SU/supermechanic/2013-8-23_03546_500.64x64.jpg Jerry's Avatar

    Jerry

    Master Mechanic

    Satisfied Customers:

    432
    ASE Master tech. 30+ years mechanic, shop forman, service manager