How JustAnswer Works:

  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.

Ask ricardo hohl Your Own Question

ricardo hohl
ricardo hohl, Instructor
Category: Chrysler
Satisfied Customers: 4067
Experience:  ase master/factory certified/and automotive instructor
Type Your Chrysler Question Here...
ricardo hohl is online now
A new question is answered every 9 seconds

Time a mitsubishi 2.4 engine with a sohc and time the balance shaft?

Customer Question

how do i time a mitsubishi 2.4 engine with a sohc and time the balance shaft?
Submitted: 4 years ago.
Category: Chrysler
Expert:  ricardo hohl replied 4 years ago.
this is the removel . next i will send you instalation.
Notes
Fig. 31 Timing Belt Replacement (part 1 Of 2)

Fig. 31 Timing Belt Replacement (part 2 Of 2)

TIMING BELT REMOVAL
Remove timing belt in numbered sequence shown in Fig. 30 parts 1 and 2 , noting following:
  1. Remove engine mount bracket as outlined under Engine Mount, Replace.

Fig. 15 Timing Mark Alignment

  1. Turn crankshaft clockwise and align timing marks to position No. 1 cylinder on its compression stroke at TDC, Fig. 15 .
  2. Remove auto tensioner.
  3. Mark belt rotating direction on belt.
  4. Tie camshaft sprocket and timing belt with a cord so that position of camshaft sprocket will not move with respect to timing belt.
  5. Using spanner wrench tool Nos. MB990767 and MD998719, or equivalents, remove camshaft sprocket nut and sprocket.
  6. Remove oil pump sprocket as follows:

Fig. 31 Silent Shaft Lock

  1. Remove plug on side of engine block, Fig. 31 .
  2. Insert a Phillips screwdriver into hole to block left silent shaft. If screwdriver will only go in 0.79-0.98 inch as it strikes against counterbalance shaft, turn sprocket once, realign timing mark and check that screwdriver goes in2.36 inches or more . Screwdriver should not be taken out until timing belt is installed.
  3. Remove oil pump sprocket nut then sprocket.
    1. Mark rotational direction on timing belt B prior to removal.

 

Customer: replied 4 years ago.

 

why do i need to remove the oil pump sprocket? how do i put this all back together?

 

Customer/p>
Expert:  ricardo hohl replied 4 years ago.
here is instalation.
Installation
Notes
Fig. 31 Timing Belt Replacement (part 1 Of 2)

Fig. 31 Timing Belt Replacement (part 2 Of 2)

TIMING BELT INSTALLATION
Install timing belt in numbered sequence shown in Fig. 30 parts 1 and 2, noting following:

Fig. 32 Support Bracket Bolt

  1. Apply sealant to engine support bracket bolt shown in Fig. 32 .

Fig. 33 Crankshaft Sprocket B Installation

  1. Install crankshaft sprocket B as shown in Fig. 33 .
  2. Install right silent shaft sprocket spacer with chamfered edge pointed toward oil seal.
  3. Ensure crankshaft sprocket B and silent shaft sprocket timing marks are aligned then install timing belt B.
  4. Adjust timing belt B tension as follows:
    1. Temporarily install timing belt B tensioner to that center of tensioner is to left and above installation bolt.
    2. Place tension on timing belt B so tension side of belt is tight then tighten tensioner bolt.

Fig. 34 Timing Belt B Tension Inspection

    1. At point marked "A and ensure belt is within .20-.28 inch when depressed for correct tension, Fig. 34 .

Fig. 35 Crankshaft Flange & Sprocket Installation

  1. Install crankshaft flange and pulley as shown in Fig. 35 .
  2. Install auto tensioner as follows:
    1. Keeping auto tensioner level clamp it in a soft jawed vise. If plug at bottom of tensioner protrudes, surround it with a washer to prevent plug from being in direct contact with vise.

Fig. 36 Tensioner Set Hole Alignment

    1. Push in rod slowly with vise until set holes are aligned, Fig. 36 .
    2. Insert a wire 0.055 inch in diameter into set holes and release tensioner from vise.
    3. Install tensioner, keeping wire installed in set holes.
  1. Install tensioner pulley onto tensioner arm. Position pinhole in tensioner pulley shaft to left of center bolt, then tighten center bolt finger tight.

Fig. 31 Silent Shaft Lock

  1. Ensure timing marks are aligned and remove plug on side of engine block, Fig. 31 . Insert a Phillips screwdriver into hole to block left silent shaft.
  2. If screwdriver cannot be inserted 2.4 inch or more turn oil pump sprocket one turn and realign timing marks. Ensure screwdriver can be inserted 2.4 inches or more . Screwdriver should not be removed until installation of timing belt is complete.
  3. Install timing belt as follows:
    1. Install timing belt around tensioner pulley and crankshaft sprocket and secure timing belt onto tensioner pulley with your left hand.
    2. Pulling timing belt with your right hand, install it around oil pump sprocket.
    3. Install belt around idler pulley.
    4. Install belt around camshaft sprocket.

Fig. 37 Timing Belt Tension Pulley Position

    1. Gently raise tensioner pulley so that belt does not sag then temporarily tighten center bolt, Fig. 37 .
  1. Adjust timing belt tension as follows:
    1. >Remove screwdriver and install plug in side of cylinder block.
    2. Turn crankshaft 90.0degrees counterclockwise .
    3. Turn crankshaft back to position No. 1 cylinder at TDC.

Fig. 38 Timing Belt Tension Adjustment

    1. Loosen tensioner pulley center bolt, then attach socket wrench tool No. MD998752, or equivalent, and a torque wrench and apply a torque of 1.88-2.03 ft. lbs. , Fig. 38 .
    2. Holding tensioner pulley with special tool, tighten center bolt to specification.

Fig. 39 Setscrew Tool Installation

    1. Install setscrew tool No. MD998738, or equivalent, into engine left support bracket until its end makes contact with tensioner arm, Fig. 39 .
    2. Turn setscrew tool to increase pressure on tensioner arm then remove wire from tensioner set holes.
    3. Rotate crankshaft two complete turns clockwise and allow to sit for 15 minutes.
    4. After 15 minutes , measure auto tensioner rod protrusion, and verify that it is within 0.15-0.18 inch specification. If not as specified, repeat steps a through h.
    5. Install rubber plug to timing belt rear cover.

Fig. 40 Timing Belt Cove Installation

  1. Install timing belt cover screws into proper location as shown in Fig. 40 .

 

ricardo hohl, Instructor
Category: Chrysler
Satisfied Customers: 4067
Experience: ase master/factory certified/and automotive instructor
ricardo hohl and 7 other Chrysler Specialists are ready to help you
Customer: replied 4 years ago.

thank you for your help. I can now finish this job.

 

thanks Ricardo

Expert:  ricardo hohl replied 4 years ago.
no problem . just make sure you copy this pictures to your files before they get deleted from the system.
Expert:  ricardo hohl replied 4 years ago.
ok.

JustAnswer in the News:

 
 
 
Ask-a-doc Web sites: If you've got a quick question, you can try to get an answer from sites that say they have various specialists on hand to give quick answers... Justanswer.com.
JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance.
Web sites like justanswer.com/legal
...leave nothing to chance.
Traffic on JustAnswer rose 14 percent...and had nearly 400,000 page views in 30 days...inquiries related to stress, high blood pressure, drinking and heart pain jumped 33 percent.
Tory Johnson, GMA Workplace Contributor, discusses work-from-home jobs, such as JustAnswer in which verified Experts answer people’s questions.
I will tell you that...the things you have to go through to be an Expert are quite rigorous.
 
 
 

What Customers are Saying:

 
 
 
  • I was skeptical at first but thought I'd give it a try. I was pleasantly surprised. Your site actually is a quality service that I would recommend to others in a heartbeat. Stan Sayre, PA
< Last | Next >
  • I was skeptical at first but thought I'd give it a try. I was pleasantly surprised. Your site actually is a quality service that I would recommend to others in a heartbeat. Stan Sayre, PA
  • I AM VERY GLAD THAT I TOOK A CHANCE ON YOUR PROBLEM SOLVING SKILLS. I WAS SUCCESSFUL IN REPLACING THE FUEL PUMP. MY TRUCK RUNS LIKE A CLOCK. IT RUNS LIKE THE DAY I BOUGHT IT. NO LUNGING FORWARD, THE TURBO REACTS THE SECOND I STOMP ON THE GAS, AND IT HAS A LOT MORE POWER AND EVEN SOUNDS BETTER TO ME. IT SAVED ABOUT $500.00 BY DOING THE WORK MYSELF. I GIVE YOU ALL THE CREDIT FOR YOUR DIAGNOSING THE PROBLEM, JUST FROM THE SYMPTONS I GAVE YOU OVER THE e MAIL. I WILL USE YOUR WEB SITE AGAIN AND REFER MY FRIENDS. THANKS SO MUCH FOR THE HELP. TOM WHITTAKER USA
  • Just a quick line to tell you how pleased I am to have my brakes working properly after all this time. Your answer was what I needed. I would certainly recommend you highly. God bless! Rev. Jerry Baysinger Holts Summit, Mo
  • I recently asked a question about my 2005 dodge ram, and I just wanted to let my Expert know that he hit the nail squarely on the head with his answer. I wanted to thank him again. Greg Pittsburgh, PA
  • Just a quick line to tell you how pleased I am to have my brakes working properly after all this time. Your answer was what I needed. I would certainly recommend you highly. God bless! Jerry Holts Summit, MO
  • Thank you so much for your answer. My initial estimate was $325; I got it done for $100 - part and labor. Lynn B. Ormond Beach, FL
  • Wonderful service, prompt, efficient, and accurate. Couldn't have asked for more. I cannot thank you enough for your help. Mary C. Freshfield, Liverpool, UK
 
 
 

Meet The Experts:

 
 
 
  • Don 'Mo Lurch'

    Aftermarket & Factory Electronics

    Satisfied Customers:

    384
    Chrysler Warnty, Heavy Line Mech, Mobile Electronics. Sales, Installation & Repair for 30 years
< Last | Next >
  • http://ww2.justanswer.com/uploads/MO/molurch/2012-6-6_214526_500.64x64.png Don 'Mo Lurch''s Avatar

    Don 'Mo Lurch'

    Aftermarket & Factory Electronics

    Satisfied Customers:

    384
    Chrysler Warnty, Heavy Line Mech, Mobile Electronics. Sales, Installation & Repair for 30 years
  • http://ww2.justanswer.com/uploads/2P/2paulm/2012-4-4_183431_justabswer.64x64.jpg Paul M ASE Master's Avatar

    Paul M ASE Master

    ASE Master Tech

    Satisfied Customers:

    117
    ASE Master Tech 20+ Years
  • http://ww2.justanswer.com/uploads/MU/muddyford/2012-6-13_1204_1.64x64.png Chris (aka - Moose)'s Avatar

    Chris (aka - Moose)

    Technician

    Satisfied Customers:

    93
    16 years of experience
  • http://ww2.justanswer.com/uploads/IV/ivestoy2/2011-7-21_44030_ivan.64x64.jpg Ivan's Avatar

    Ivan

    ASE Certified Master Technician

    Satisfied Customers:

    55
    ASE Master Tech w/ 20+ years in the field. Self employed for 9 years. Member of AUTOLAB radio show.
  • http://ww2.justanswer.com/uploads/AC/acuramstr/2012-6-6_181032_me.64x64.jpg AUTOMSTR's Avatar

    AUTOMSTR

    ASE Certified Technician

    Satisfied Customers:

    0
    ASE Master Tech, L1, CA Smog ,30 YRS EXP
  • http://ww2.justanswer.com/uploads/AM/amedee/2013-10-24_23656_Amedee1.64x64.jpg Amedee's Avatar

    Amedee

    Chrysler Technician

    Satisfied Customers:

    787
    ASE Master Technician advanced level specialist
  • http://ww2.justanswer.com/uploads/SU/supermechanic/2013-8-23_03546_500.64x64.jpg Jerry's Avatar

    Jerry

    Master Mechanic

    Satisfied Customers:

    432
    ASE Master tech. 30+ years mechanic, shop forman, service manager