How JustAnswer Works:
  • Ask an Expert
    Experts are full of valuable knowledge and are ready to help with any question. Credentials confirmed by a Fortune 500 verification firm.
  • Get a Professional Answer
    Via email, text message, or notification as you wait on our site.
    Ask follow up questions if you need to.
  • 100% Satisfaction Guarantee
    Rate the answer you receive.
Ask Tim's Auto Repair Your Own Question
Tim's Auto Repair
Tim's Auto Repair, mechanic
Category: Chevy
Satisfied Customers: 15486
Experience:  Have owned a repair shop for 25 yrs.
14541291
Type Your Chevy Question Here...
Tim's Auto Repair is online now
A new question is answered every 9 seconds

heater core replacement on a g20 1990?

This answer was rated:

heater core replacement on a g20 1990?

hi

this may help you

thanks

 

1990-95 MODELS

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.


To install:

  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

 

Customer: replied 6 years ago.
would you have any picture diagrams to help me out on the way to refix things together...

sorry i have few pictures for this model

thanks

 

- G20 VAN -

 

1990-95 MODELS

  1. please ACCEPT my answer so I can get credit for my work.i don't receive commission unless you do ..I'm not always going to be giving you good news,so please don't let this stand in the way of you accepting my answer.it does not cost you more money.we will still be able to communicate.. Bonuses and positive feedback are appreciated!if you are not satisfied with my answer,please do not leave bad feed back,i will gladly opt out and let another expert handle the question.PLEASE ASK IF YOU NEED MORE HELP
  2. FIG : Fig. 2: Sectional views of the auxiliary heater plumbing components - 1987-95 models

    image

Tim's Auto Repair and 3 other Chevy Specialists are ready to help you

Related Chevy Questions